Use the new PWM controller binding which now relies on passing all
clock inputs available on the SoC (instead of passing the "wanted"
clock input for a given board).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241227212514.1376682-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The Broadcom WiFi/BT SDIO nodes are now inherited from the P212 common dtsi
so we can remove them from the VIM1 board dts.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123065504.2669769-4-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
'clock-frequency' is not part of the DT binding and not supported by the
Linux driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221024165549.74574-6-sebastian.reichel@collabora.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Improve gxl-s905x-khadas-vim wifi performance
* change freq from 60Mhz to 100Mhz
100Mhz works well same as in meson-khadas-vim3.dtsi
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210622044334.769791-1-art@khadas.com
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
Signed-off-by: Alexander Dahl <post@lespocky.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201228163217.32520-5-post@lespocky.de
Reorder the VIM/VIM2 includes/bindings to follow the format of other dts
in the Amlogic tree and remove a stray empty line in the VIM2 dts.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201203061605.9603-1-christianshewitt@gmail.com
Enable the rtc node on VIM1/VIM2 boards so users can simply attach a power
cell and use the on-board RTC without modifying the device-tree.
Cold boot with no cell attached is gracefully handled:
VIM2:~ # dmesg | grep rtc
[ 7.716150] rtc-hym8563 1-0051: no valid clock/calendar values available
[ 7.716957] rtc-hym8563 1-0051: registered as rtc0
[ 7.729850] rtc-hym8563 1-0051: no valid clock/calendar values available
[ 7.729877] rtc-hym8563 1-0051: hctosys: unable to read the hardware clock
[ 8.126768] rtc-hym8563 1-0051: no valid clock/calendar values available
Warm boot (and any boot with cell attached) recalls stored values resulting
in consistently faster (re)boot times:
VIM2:~ # dmesg | grep rtc
[ 7.441671] rtc-hym8563 1-0051: registered as rtc0
[ 7.442663] rtc-hym8563 1-0051: setting system clock to 2020-11-16T05:49:59 UTC (1605505799)
Suggested-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201116064147.12062-1-christianshewitt@gmail.com
Add the correcly architectured USB Glue node and adapt all the Amlogic
GXL and GXM board to the new organization.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326134507.4808-11-narmstrong@baylibre.com
Fix DTC warnings:
arch/arm/dts/meson-gxl-s905x-khadas-vim.dtb: Warning (avoid_unnecessary_addr_size):
/gpio-keys-polled: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Fixes: e15d2774b8 ("ARM64: dts: meson-gxl: add support for the Khadas VIM board")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.
Fixes: b409f625a6 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The gpio line names were set in the pinctrl node instead of the gpio node,
at the time it was merged, it worked, but was obviously wrong.
This patch moves the properties to the gpio nodes.
Fixes: 60795933b7 ("ARM64: dts: meson-gxl-khadas-vim: Add GPIO lines names")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables Bluetooth support for the following models:
- Khadas VIM basic (AP6212) using firmware BCM43438A1.hcd
- Khadas VIM pro (AP6255) using firmware BCM4345C0.hcd
The AP6212 module used on the VIM basic has an ID clash with another
device. To get Bluetooth working you either need to apply a kernel
patch to drivers/bluetooth/btbcm.c so 0x2209 loads BCM43438A1 or the
BCM43438A1.hcd firmware must be renamed to BCM43430A1.hcd.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N gpio has been moved so the gpio-line-names of the kvim
must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch describes the GPIO lines usage on the Khadas VIM board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use the specific compatible for AO pwms so the pwms input can
be correctly set
FDIV4 is not present on the pwm A0, so change kadhas vim input
clocks to xtal.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
bcrmf -> brcmf -> wifi
Fixes: e15d2774b8 ("ARM64: dts: meson-gxl: add support for the Khadas VIM board")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM series consists of two boards which are almost
identical:
They are both using the same GXL S905X SoC, 100Mbit/s ethernet
(through the SoC-internal PHY), 2GB DDR3 memory, a micro-SD card slot,
onboard eMMC, Broadcom based SDIO WIFI, 2x USB A and 1x USB Type-C (the
latter with OTG support). The red LED is driven by PWM_AO_B (which
allows dimming), while the blue LED is managed by the firmware.
The differences are:
- the VIM Pro has a 16GB eMMC module, while the VIM only has 8GB
- the VIM Pro uses an AP6255 a/b/g/n/ac WIFI module, while the VIM comes
with an AP6212 b/g/n SDIO WIFI module
(the Vim uses an 8GB eMMC module, while
The boards are based on Amlogic's GXL S905X P212 reference design, which
is why most of the functionality (all MMC controllers and power
sequences, IR remote input, the main UART, ADC and ethernet) is simply
inherited from meson-gxl-s905x-p212.dtsi.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
