This commit fixes a typo introduced in commit
ee368a10d0 ("ARM: dts: am335x-boneblack.dts: unique gpio-line-names").
gpio0_7 is located on the P9 header on the BBB.
This was verified with a BeagleBone Black by toggling the pin and
checking with a multimeter that it corresponds to pin 42 on the P9
header.
Signed-off-by: Albin Törnqvist <albin.tornqvist@codiax.se>
Link: https://lore.kernel.org/r/20250624114839.1465115-2-albin.tornqvist@codiax.se
Fixes: ee368a10d0 ("ARM: dts: am335x-boneblack.dts: unique gpio-line-names")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The wiring of the RS-485 transceiver of UART0 of the PDU-001 board
allows sending or receiving date exclusively. In other words: no
character transmitted will ever be received.
Hence the tx-filter counter in the OMAP serial driver can't work
correctly as it relies on receiving the transmitted characters.
This in turn will prevent reception of data unless we disable the
tx-filter counter.
This patch disables the tx-filter counter by enabling the DTS setting
rs485-rx-during-tx. This might sound like the opposite to be done but
it uses the enabling of rs485-rx-during-tx not for receiving the data
transmitted but for disabling the tx-fiter counter.
Tested-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Felix Brack <fb@ltec.ch>
Link: https://lore.kernel.org/r/20250529135324.182868-1-fb@ltec.ch
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SeeedStudio BeagleBone Green Eco (BBGE) is a clone of the BeagleBone Green
(BBG). It has minor differences from the BBG, such as a different PMIC,
a different Ethernet PHY, and a larger eMMC.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250620-bbg-v5-3-84f9b9a2e3a8@bootlin.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This reverts commit c761028ef5.
The commit being reverted updated the "ranges" property for the sake of
readability. However, this change is no longer appropriate due to the
following reasons:
- On many SoCs, the PCIe parent bus translates CPU addresses to different
values before passing them to the PCIe controller.
- The reverted commit introduced a fake address translation, which violates
the fundamental DTS principle: the device tree should reflect actual
hardware behavior.
Reverting this change prepares for the cleanup of the driver's
cpu_addr_fixup() hook.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250411153454.3258098-1-Frank.Li@nxp.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 'rts-gpio' (without trailing 's') is deprecated in favor of
'rts-gpios'. Kernel supports both variants, so switch the DTS to
preferred one.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250514125158.56285-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Bluetooth is available on the other Panda board versions, too, so move
stuff to common and specify the needed clock properly.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250427052735.88133-3-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Pandaboard needs a 32k clock in the TWL6030 to be enabled
for Wifi to work.
With some luck, it is enabled by some U-Boot fork.
Do not rely on it and properly specify the requirement.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250427052735.88133-2-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This property is irrelevant for the ad5820 DAC,
the driver nor the hardware indicate use of channel cells.
Fixes: d510d12f26 ("ARM: dts: nokia n900: update dts with camera support")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20250213203208.93316-1-david@ixit.cz
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
When moving the model and compatible properties out of the common
Pandaboard files and in to the specific boards, the omap4-panda-a4
file wasn't updated as well and so has lacked a model and compatible
entry ever since.
Fixes: a1a57abaaf ("ARM: dts: omap4-panda: Fix model and SoC family details")
Signed-off-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20250123174901.1182176-2-trini@konsulko.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Bindings expect GPIO hog names to end with 'hog' suffix, so correct it
to fix dtbs_check warning:
omap3-evm.dtb: en_on_board_gpio_61: $nodename:0: 'en_on_board_gpio_61' does not match '^.+-hog(-[0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250115211648.194016-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f ("ARM: dts: gta04: fix excess dma channel usage")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
A bus_dma_limit was added for l3 bus by commit cfb5d65f25
("ARM: dts: dra7: Add bus_dma_limit for L3 bus") to fix an issue
observed only with SATA on DRA7-EVM with 4GB RAM and CONFIG_ARM_LPAE
enabled.
Since kernel 5.13, the SATA issue can be reproduced again following
the SATA node move from L3 bus to L4_cfg in commit 8af15365a3
("ARM: dts: Configure interconnect target module for dra7 sata").
Fix it by adding an empty dma-ranges property to l4_cfg and
segment@100000 nodes (parent device tree node of SATA controller) to
inherit the 2GB dma ranges limit from l3 bus node.
Note: A similar fix was applied for PCIe controller by commit
90d4d3f4ea ("ARM: dts: dra7: Fix bus_dma_limit for PCIe").
Fixes: 8af15365a3 ("ARM: dts: Configure interconnect target module for dra7 sata").
Link: https://lore.kernel.org/linux-omap/c583e1bb-f56b-4489-8012-ce742e85f233@smile.fr/
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Romain Naour <romain.naour@skf.com>
Link: https://lore.kernel.org/r/20241115102537.1330300-1-romain.naour@smile.fr
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
dtbs_check was moaning about twl6030-power, use the standard property
instead.
Apparently that twl6030 power snippet slipped in without the
corresponding driver. Now it is handled by the standard property.
CC: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
Link: https://lore.kernel.org/r/20240915193527.1071792-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit b9bf561261 ("ARM: dts: am335x-bone-common: Increase MDIO
reset deassert time") already increased the MDIO reset deassert delay
from 6.5 to 13 ms, but this may still cause Ethernet PHY probe failures:
SMSC LAN8710/LAN8720 4a101000.mdio:00: probe with driver SMSC LAN8710/LAN8720 failed with error -5
On BeagleBone Black Rev. C3, ETH_RESETn is controlled by an open-drain
AND gate. It is pulled high by a 10K resistor, and has a 4.7µF
capacitor to ground, giving an RC time constant of 47ms. As it takes
0.7RC to charge the capacitor above the threshold voltage of a CMOS
input (VDD/2), the delay should be at least 33ms. Considering the
typical tolerance of 20% on capacitors, 40ms would be safer. Add an
additional safety margin and settle for 50ms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/9002a58daa1b2983f39815b748ee9d2f8dcc4829.1730366936.git.geert+renesas@glider.be
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Operating stable without reduced chip life at 1Ghz needs several
technologies working: The technologies involve
- SmartReflex
- DVFS
As this cannot directly specified in the OPP table as dependecies in the
devicetree yet, use the turbo flag again to mark this OPP as something
special to have some kind of opt-in.
So revert commit
5f1bf7ae84 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Practical reasoning:
At least the GTA04A5 (DM3730) has become unstable with that OPP enabled.
Furthermore nothing enforces the availability of said technologies,
even in the kernel configuration, so allow users to rather opt-in.
Cc: Stable@vger.kernel.org
Fixes: 5f1bf7ae84 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241018214727.275162-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Define the GPIO expander which controls at least some camera gpios.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-5-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Set them to the state seen in a running system, initialized
by vendor u-boot or kernel. Add line names where they are defined in the
vendor kernel.
gpio15 resets something in the display, otherwise meaning of the
gpios is not known.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-4-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Wire up the regulators where usage is plausible. Do not
wire them if purpose/usage is unclear like 5V for
many things requiring lower voltages.
Tested on vendor kernel that backlight definitively does not react
on blc_[rl] GPIOs.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-3-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
To properly have things running after cold boot, define
GPIO regulators. Naming is based on board file.
In the vendor kernel they are enabled in a function
called bt2ws_dcdc_init() if the system is not booted just
to charge the battery.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-2-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
linux,mtd-name is only applicable for PHYSMAP driver and not for
OneNAND.
Fixes the below dtbs_check warning
"omap3430-sdp.dtb: onenand@2,0: Unevaluated properties are not allowed ('linux,mtd-name' was unexpected)"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240903-gpmc-dtb-v1-3-380952952e34@kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
"gpmc,device-nand" is not used any more and leads to below dtbs_check
warning so drop it.
"nand@0,0: Unevaluated properties are not allowed ('gpmc,device-nand' was unexpected)"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240903-gpmc-dtb-v1-2-380952952e34@kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
linux,mtd-name is only supported by PHYSMAP driver and not applicable
to NAND controller/flash nodes.
Fixes the below dtbs_check warning on many OMAP boards.
"nand@0,0: Unevaluated properties are not allowed ('linux,mtd-name' was unexpected)"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240903-gpmc-dtb-v1-1-380952952e34@kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
New SoC support for Broadcom bcm2712 (Raspberry Pi 5) and Renesas
R9A09G057 (RZ/V2H(P)) and Qualcomm Snapdragon 414 (MSM8929), all three
of these are variants of already supported chips, in particular the last
one is almost identical to MSM8939.
Lots of updates to Mediatek, ASpeed, Rockchips, Amlogic, Qualcomm,
STM32, NXP i.MX, Sophgo, TI K3, Renesas, Microchip at91, NVIDIA Tegra,
and T-HEAD.
The added Qualcomm platform support once again dominates the changes,
with seven phones and three laptops getting added in addition to
many new features on existing machines. The Snapdragon X1E support
specifically keeps improving.
The other new machines are:
- eight new machines using various 64-bit Rockchips SoCs, both
on the consumer/gaming side and developer boards
- three industrial boards with 64-bit i.MX, which is a very
low number for them.
- four more servers using a 32-bit Speed BMC
- three boards using STM32MP1 SoCs
- one new machine each using allwinner, amlogic, broadcom
and renesas chips.
-----BEGIN PGP SIGNATURE-----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=r07W
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"New SoC support for Broadcom bcm2712 (Raspberry Pi 5) and Renesas
R9A09G057 (RZ/V2H(P)) and Qualcomm Snapdragon 414 (MSM8929), all three
of these are variants of already supported chips, in particular the
last one is almost identical to MSM8939.
Lots of updates to Mediatek, ASpeed, Rockchips, Amlogic, Qualcomm,
STM32, NXP i.MX, Sophgo, TI K3, Renesas, Microchip at91, NVIDIA Tegra,
and T-HEAD.
The added Qualcomm platform support once again dominates the changes,
with seven phones and three laptops getting added in addition to many
new features on existing machines. The Snapdragon X1E support
specifically keeps improving.
The other new machines are:
- eight new machines using various 64-bit Rockchips SoCs, both on the
consumer/gaming side and developer boards
- three industrial boards with 64-bit i.MX, which is a very low
number for them.
- four more servers using a 32-bit Speed BMC
- three boards using STM32MP1 SoCs
- one new machine each using allwinner, amlogic, broadcom and renesas
chips"
* tag 'soc-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (672 commits)
arm64: dts: allwinner: h5: NanoPi NEO Plus2: Use regulators for pio
arm64: dts: mediatek: add audio support for mt8365-evk
arm64: dts: mediatek: add afe support for mt8365 SoC
arm64: dts: mediatek: mt8186-corsola: Disable DPI display interface
arm64: dts: mediatek: mt8186: Add svs node
arm64: dts: mediatek: mt8186: Add power domain for DPI
arm64: dts: mediatek: mt8195: Correct clock order for dp_intf*
arm64: dts: mt8183: add dpi node to mt8183
arm64: dts: allwinner: h5: NanoPi Neo Plus2: Fix regulators
arm64: dts: rockchip: add CAN0 and CAN1 interfaces to mecsbc board
arm64: dts: rockchip: add CAN-FD controller nodes to rk3568
arm64: dts: nuvoton: ma35d1: Add uart pinctrl settings
arm64: dts: nuvoton: ma35d1: Add pinctrl and gpio nodes
arm64: dts: nuvoton: Add syscon to the system-management node
ARM: dts: Fix undocumented LM75 compatible nodes
arm64: dts: toshiba: Fix pl011 and pl022 clocks
ARM: dts: stm32: Use SAI to generate bit and frame clock on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Switch bitclock/frame-master to flag on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Sort properties in audio endpoints on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Add MECIO1 and MECT1S board variants
...
"lm75" without any vendor is undocumented. It works with the Linux
kernel since the I2C subsystem will do matches of the compatible string
without a vendor prefix to the i2c_device_id and/or driver name.
Mostly replace "lm75" with "national,lm75" as that's the original part
vendor and the compatible which matches what "lm75" matched with. In a
couple of cases the node name or compatible gives a clue to the actual
part and vendor and a more specific compatible can be used. In these
cases, it does change the variant the kernel picks.
"nct75" is an OnSemi part which is compatible with TI TMP75C based on
a comparison of the OnSemi NCT75 datasheet and configuration the Linux
driver uses. Adding an OnSemi compatible would be an ABI change.
"nxp,lm75" is most likely an NXP part. Alexander Stein says the i.MX53
boards are a NXP LM75A as well. NXP makes a LM75A and LM75B. Both are
11-bit resolution and 100ms sample time. The "national,lm75a" is
9-bit, so "national,lm75b" is the closest match for both NXP variants.
While we're here, fix the node names to use the generic name
"temperature-sensor".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com> # am335x-nano.dts
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx53-mba53.dts, imx53-tqma53.dtsi
Link: https://lore.kernel.org/r/20240816164717.1585629-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Negate the values reported for the accelerometer z-axis in order to
match Documentation/devicetree/bindings/iio/mount-matrix.txt.
Fixes: 14a213dcb0 ("ARM: dts: n900: use iio driver for accelerometer")
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-By: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240722113137.3240847-1-absicsz@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Bit clock and frame clock are provided by the mcasp. Change the
simple card settings regarding the clock provider and the mclk-fs for
usage with typical 44.1 kHz and 48 kHz sample rates.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Link: https://lore.kernel.org/r/20240730092353.10209-2-d.haller@phytec.de
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
RTS pin seems to have inverted behavior on am335x, other than expected
with default "rs485-rts-active-high" (instead of low on idle, high on send,
it is the opposite). Transceiver datasheet also suggests a pulldown.
Add includes to pin definitions that are used.
Signed-off-by: Steffen Hemer <s.hemer@phytec.de>
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Link: https://lore.kernel.org/r/20240730092353.10209-1-d.haller@phytec.de
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Prior to commit df16c1c51d ("net: phy: mdio_device: Reset device only
when necessary") MDIO reset deasserts were performed twice during boot.
Now that the second deassert is no longer performed, device probe
failures happen due to the change in timing with the following error
message:
SMSC LAN8710/LAN8720: probe of 4a101000.mdio:00 failed with error -5
Restore the original effective timing, which resolves the probe
failures.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20240531183817.2698445-1-colin.foster@in-advantage.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
DT schema expects panel timings node to follow certain pattern,
dtbs_check warnings:
am335x-pdu001.dtb: display-timings: '240x320p16' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
Linux drivers do not care about node name, so this should not have
effect on Linux.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # For DaVinci
Link: https://lore.kernel.org/r/20240509104813.216655-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On dra76x, most dpll_gmac output clksel clocks are in registers from
CM_CLKSEL_DPLL_GMAC to CM_DIV_H13_DPLL_GMAC. In addition to that, there
are there more clocks in the CTRL_CORE_SMA_SW_0 register.
Let's group the CTRL_CORE_SMA_SW_0 clocks using the clksel binding to
reduce make W=1 dtbs unique_unit_address warnings, and stop using the
custom the ti,bit-shift property in favor of the standard reg property.
Let's also add a comment for the CTRL_CORE_SMA_SW_0 clock that matches the
documentation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the clkcsel binding we can drop the custom ti,bit-shift devicetree
property in favor of the standard reg property and reduce the number of
clocks to update for the make W-1 dtbs warnings.
Let's also add a comment for the clocksel clock that matches the
documentation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the clkcsel binding we can drop the custom ti,bit-shift devicetree
property in favor of the standard reg property and reduce the number of
clocks to update for the make W-1 dtbs warnings.
Let's also add a comment for the clocksel clock that matches the
documentation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the clkcsel binding we can drop the custom ti,bit-shift devicetree
property in favor of the standard reg property and reduce the number of
clocks to update for the make W-1 dtbs warnings.
Let's also add a comment for the clocksel clock that matches the
documentation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
