Commit graph

13 commits

Author SHA1 Message Date
Krzysztof Kozlowski
988cca008e ARM: dts: st: stm32: Align wifi node name with bindings
Since commit 3c3606793f ("dt-bindings: wireless: bcm4329-fmac: Use
wireless-controller.yaml schema"), bindings expect 'wifi' as node name:

  stm32h750i-art-pi.dtb: bcrmf@1: $nodename:0: 'bcrmf@1' does not match '^wifi(@.*)?$'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250424084706.105049-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2025-05-14 10:36:14 +02:00
Fabrice Gasnier
2879145733 ARM: dts: stm32: add counter subnodes on stm32mp135f-dk
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-12-20 08:20:25 +01:00
Christophe Roullier
6b44fdef4c ARM: dts: stm32: add support of WLAN/BT on stm32mp135f-dk
Add support of WLAN/BT Murata Type 1DX module:
- usart2 is used for Bluetooth interface
- sdmmc2 is used for WLAN (sdio) interface

Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-10-29 16:41:43 +01:00
Valentin Caron
d6e424f926 ARM: dts: stm32: rtc, add LSCO to WLAN/BT module on stm32mp135f-dk
On stm32mp135f-dk board, WLAN/BT module LPO_IN pin is wired to
RTC OUT2_RMP pin.

Provide a pinctrl configuration to enable LSCO on OUT2_RMP.

Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-10-29 16:41:42 +01:00
Christophe Roullier
e9442f1fa4 ARM: dts: stm32: add ethernet1 for STM32MP135F-DK board
Ethernet1: RMII with crystal
Ethernet2: RMII with no cristal, need "phy-supply" property to work,
today this property was managed by Ethernet glue, but should be present
and managed in PHY node. So I will push second Ethernet in next step.

PHYs used are SMSC (LAN8742A)

Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-07-05 14:45:24 +02:00
Uwe Kleine-König
710d4f79bd ARM: dts: stm32: Document output pins for PWMs on stm32mp135f-dk
To simplify identifying the pins where the PWM output is routed to,
add a comment to each PWM device about the respective pin on the
expansion connector.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-07-05 14:45:24 +02:00
Yannick Fertre
3d058df954 ARM: dts: stm32: add goodix touchscreen on stm32mp135f-dk
Touchscreen reset needs to be configured
via the pinctrl not the driver (a pull-down resistor
has been soldered onto the reset line which forces
the touchscreen to reset state).
Interrupt line must have a pull-down resistor
in order to freeze the i2c address at 0x5D.

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-06-05 10:35:00 +02:00
Alain Volmat
26c7b370eb ARM: dts: stm32: enable camera support on stm32mp135f-dk board
On STM32MP135F-DK board the camera support is made of the
CSI based GC2145 sensor, connected to the ST-MIPID02 CSI to parallel
bridge, connected to the DCMIPP parallel input.

Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-06-05 10:19:07 +02:00
Raphael Gallais-Pou
da5216c68b ARM: dts: stm32: enable display support on stm32mp135f-dk board
Link panel and display controller.
Enable panel, backlight and display controller.

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-04-25 15:00:30 +02:00
Thomas Bourgoin
45734a13fa ARM: dts: stm32: enable crypto accelerator on stm32mp135f-dk
Add the crypto accelerator enable on stm32mp135f-dk board.

Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-02-29 10:14:08 +01:00
Lionel Debieve
d4e12273a7 ARM: dts: stm32: enable CRC on stm32mp135f-dk
Enable Cyclic redundancy check on stm32mp135f-dk.

Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2024-02-29 10:14:07 +01:00
Etienne Carriere
4c757f6b80 ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
Since OP-TEE release tag 3.22.0, OP-TEE SCMI service for STM32MP13x
SoC family exposes PMIC voltage regulators. This change defines
them in the platform DTS file and removes the fixed regulators that
were previously defined to abstract them before OP-TEE firmware was
ready.

Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Pascal Paillet <p.paillet@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2023-08-16 10:58:45 +02:00
Rob Herring
724ba67515 ARM: dts: Move .dts files to vendor sub-directories
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
  been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
  company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
2023-06-21 11:39:50 -06:00
Renamed from arch/arm/boot/dts/stm32mp135f-dk.dts (Browse further)