Disable internal pull down for the following GPIO lines.
- GPIOL4 - Reset PCH registers in the rtc.
- GPIOL5 - Reset portition of Intel ME
- GPIOL6 - FM smi active
- GPIOL7 - psu all dc power good.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20250204194115.3899174-10-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
- Mark following GPIO lines as input high:
- GPIOL4 (reset PCH registers)
- GPIOL5 (reset portition of intel ME)
- Mark isolate errors from cpu1 gpio (GPIOO6) as active low output.
- The fan controller reset line should be active high.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20250204194115.3899174-9-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Removing voltage regulators max8952 from device tree. Those are fully
controlled by hardware and firmware should not touch them.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20250204194115.3899174-8-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Rename LEDs with meaningful names for easier identification.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20250204194115.3899174-7-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reduce sgpio speed to improve stability with the current PCB layout.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20250204194115.3899174-6-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add following GPIO line name so that userspace can control them
- Flash write override
- pch-reset
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20250204194115.3899174-5-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
The system1 uses Intel common redundant (crps185) power supplies so move
to correct new crps driver.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20241217173537.192331-5-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add following GPIO line names so that userspace can control them
- PCH related GPIOs
- FPGA related GPIOs
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://patch.msgid.link/20241001191756.234096-4-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Enable serial GPIO0. Set number of GPIO lines to 128 and bus frequency
to 1MHz.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://patch.msgid.link/20241001191756.234096-3-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Bump up i2c8 and i2c15 bus frequency so that PCIe slot and FPGA runs
faster
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://patch.msgid.link/20241001191756.234096-2-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
- Changed temperature sensor monitor chip from tmp423 to tmp432
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20240605160604.2135840-1-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Added a device tree for IBM system1 BMC board, which uses AST2600 SoC.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-3-ninad@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
