In the AMD P-States Performance Scale diagram, the labels for "Max Perf"
and "Lowest Perf" were incorrectly used to define the range for
"Desired Perf".The "Desired performance target" should be bounded by the
"Maximum requested performance" and the "Minimum requested performance",
which corresponds to "Max Perf" and "Min Perf", respectively.
Signed-off-by: Shouye Liu <shouyeliu@tencent.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250522070140.17557-1-shouyeliu@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Extend the "scaling_setspeed" sysfs attribute description in the
userspace governor documentation to cover possible differences
between the requested and actual CPU frequency.
Signed-off-by: Shashank Balaji <shashank.mahadasyam@sony.com>
Link: https://patch.msgid.link/20250527-userspace-governor-doc-v2-2-0e22c69920f2@sony.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Highlights:
- alienware-wmi-wmax:
- Add HWMON support
- Add ABI and admin-guide documentation
- Expose GPIO debug methods through debug FS
- Support manual fan control and "custom" thermal profile
- amd/hsmp:
- Add sysfs files to show HSMP telemetry
- Report power readings and limits via hwmon
- amd/isp4: Add AMD ISP platform config for OV05C10
- asus-wmi:
- Refactor Ally suspend/resume to work better with older FW
- hid-asus: check ROG Ally MCU version and warn about old FW versions
- dasharo-acpi: Add driver for Dasharo devices supporting fans and
temperatures monitoring
- dell-ddv:
- Expose the battery health and manufacture date to userspace using
power supply extensions
- Implement the battery matching algorithm
- dell-pc:
- Improve error propagation
- Use faux device
- int3472:
- Add delays to avoid GPIO regulator spikes
- Add handshake pin support
- Make regulator supply name configurable and allow registering more
than 1 GPIO regulator
- Map mt9m114 powerdown pin to powerenable
- intel/pmc: Add separate SSRAM Telemetry driver
- intel-uncore-freq: Add attributes to show agent types and die ID
- ISST:
- Support SST-TF revision 2 (allows more cores per bucket)
- Support SST-PP revision 2 (fabric 1 frequencies)
- Remove unnecessary SST MSRs restore (the package retains MSRs
despite CPU offlining)
- mellanox: Add support for SN2201, SN4280, SN5610, and SN5640
- mellanox: mlxbf-pmc: Support additional PMC blocks
- oxpec:
- Add OneXFly variants
- Add support for charge limit, charge thresholds, and turbo LED
- Distinguish current X1 variants to avoid unwanted matching to new
variants
- Follow hwmon conventions
- Move from hwmon/oxp-sensors to platform/x86 to match the enlarged
scope
- power: supply:
- Add inhibit-charge-awake (needed by oxpec)
- Add additional battery health status values ("blown fuse" and "cell
imbalance") (needed by dell-ddv)
- powerwell-ec: Add driver for Portwell EC supporting GPIO and watchdog
- thinkpad-acpi: Support camera shutter switch hotkey
- tuxedo: Add virtual LampArray for TUXEDO NB04 devices
- tools/power/x86/intel-speed-select:
- Support displaying SST-PP revision 2 fields
- Skip uncore frequency update on newer generations of CPUs
- Miscellaneous cleanups / refactoring / improvements
The following is an automated shortlog grouped by driver:
ABI: testing: sysfs-class-oxp:
- add missing documentation
- add tt_led attribute documentation
Add AMD ISP platform config for OV05C10:
- Add AMD ISP platform config for OV05C10
alienware-wmi-wmax:
- Add a DebugFS interface
- Add HWMON support
- Add support for manual fan control
- Add support for the "custom" thermal profile
- Expose GPIO debug methods
- Fix awcc_hwmon_fans_init() label logic
- Fix uninitialized bitmap in awcc_hwmon_fans_init()
- Improve ID processing
- Improve internal AWCC API
- Improve platform profile probe
- Modify supported_thermal_profiles[]
- Rename thermal related symbols
amd/hsmp: acpi:
- Add sysfs files to display HSMP telemetry
amd/hsmp:
- fix building with CONFIG_HWMON=m
- Report power via hwmon sensors
- Use a single DRIVER_VERSION for all hsmp modules
arm64: huawei-gaokun-ec:
- Remove unneeded semicolon
asus-wmi:
- fix build without CONFIG_SUSPEND
- Refactor Ally suspend/resume
Avoid -Wflex-array-member-not-at-end warning:
- Avoid -Wflex-array-member-not-at-end warning
barco-p50:
- use new GPIO line value setter callbacks
dell-ddv:
- Expose the battery health to userspace
- Expose the battery manufacture date to userspace
- Implement the battery matching algorithm
dell-pc:
- Propagate errors when detecting feature support
- Transition to faux device
- Use non-atomic bitmap operations
docs: ABI:
- Fix "aassociated" to "associated"
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Documentation: ABI:
- Add sysfs platform and debugfs ABI documentation for alienware-wmi
Documentation: admin-guide: laptops:
- Add documentation for alienware-wmi
Documentation: admin-guide: pm:
- Add documentation for agent_types
- Add documentation for die_id
Documentation: wmi: alienware-wmi:
- Add GPIO control documentation
Documentation: wmi:
- Improve and update alienware-wmi documentation
Do not enable by default during compile testing:
- Do not enable by default during compile testing
hid-asus:
- check ROG Ally MCU version and warn
hwmon:
- (oxp-sensors) Add all OneXFly variants
- (oxp-sensors) Distinguish the X1 variants
int0002:
- use new GPIO line value setter callbacks
int3472:
- Add handshake pin support
- Add skl_int3472_register_clock() helper
- Avoid GPIO regulator spikes
- Debug log when remapping pins
- Drop unused gpio field from struct int3472_gpio_regulator
- Export int3472_discrete_parse_crs()
- For mt9m114 sensors map powerdown to powerenable
- Make regulator supply name configurable
- Move common.h to public includes, symbols to INTEL_INT3472
- Prepare for registering more than 1 GPIO regulator
- Remove unused sensor_config struct member
- Rework AVDD second sensor quirk handling
- Stop setting a supply-name for GPIO regulators
- Stop using devm_gpiod_get()
intel/pmc:
- Convert index variables to be unsigned
- Create Intel PMC SSRAM Telemetry driver
- Improve pmc_core_get_lpm_req()
- Move error handling to init function
- Move PMC Core related functions
- Move PMC devid to core.h
- Remove unneeded header file inclusion
- Remove unneeded io operations
- Rename core_ssram to ssram_telemetry
- Use devm for mutex_init
intel: power-domains:
- Add interface to get Linux die ID
intel-uncore-freq:
- Add attributes to show agent types
- Add attributes to show die_id
intel/vsec:
- Change return type of intel_vsec_register
Introduce dasharo-acpi platform driver:
- Introduce dasharo-acpi platform driver
ISST:
- Do Not Restore SST MSRs on CPU Online Operation
- Support SST-PP revision 2
- Support SST-TF revision 2
- Update minor version
mellanox:
- Cosmetic changes to improve code style
- Introduce support of Nvidia smart switch
- Rename field to improve code readability
mlxbf-pmc:
- Support additional PMC blocks
mlx-platform:
- Add support for new Nvidia system
mlxreg-dpu:
- Add initial support for Nvidia DPU
- Fix smatch warnings
nvsw-sn2200:
- Add support for new system flavour
- Fix .items in nvsw_sn2201_busbar_hotplug
oxpec:
- Add a lower bounds check in oxp_psy_ext_set_prop()
- Add charge threshold and behaviour to OneXPlayer
- Add support for the OneXPlayer G1
- Add turbo led support to X1 devices
- Adhere to sysfs-class-hwmon and enable pwm on 2
- Convert defines to using tabs
- Follow reverse xmas convention for tt_toggle
- Make turbo val apply a bitmask
- Move fan speed read to separate function
- Move hwmon/oxp-sensors to platform/x86
- Move pwm_enable read to its own function
- Move pwm value read/write to separate functions
- Rename ec group to tt_toggle
- Rename rval to ret in tt_toggle
portwell-ec:
- Add GPIO and WDT driver for Portwell EC
power: supply:
- add inhibit-charge-awake to charge_behaviour
power: supply: core:
- Add additional health status values
silicom:
- use new GPIO line value setter callbacks
sony-laptop:
- Remove unused sony laptop camera code
thermal/drivers/acerhdf:
- Constify struct thermal_zone_device_ops
thinkpad-acpi:
- Add support for new hotkey for camera shutter switch
tools/power/x86/intel-speed-select:
- Skip uncore frequency update
- Support SST PP revision 2 fields
- v1.23 release
tuxedo:
- Add virtual LampArray for TUXEDO NB04 devices
- Prevent invalid Kconfig state
Use strscpy()/scnprintf() with acpi_device_name/class():
- Use strscpy()/scnprintf() with acpi_device_name/class()
Merges:
- Merge branch 'fixes' into for-next
- Merge branch 'intel-sst' of https://github.com/spandruvada/linux-kernel into for-next
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSCSUwRdwTNL2MhaBlZrE9hU+XOMQUCaDWJ7wAKCRBZrE9hU+XO
MT8JAQDWW6qBoXuqpd6Yx1oOyROc6gJMQAsS9sNc7I60mGooEAEAnTLhOHDGkKb5
av1fz/SmXGl7joeRYkZV9FRzJ/26AAk=
=ytxa
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers updates from Ilpo Järvinen:
"The changes are mostly business as usual. Besides pdx86 changes, there
are a few power supply changes needed for related pdx86 features, move
of oxpec driver from hwmon (oxp-sensors) to pdx86, and one FW version
warning to hid-asus.
Highlights:
- alienware-wmi-wmax:
- Add HWMON support
- Add ABI and admin-guide documentation
- Expose GPIO debug methods through debug FS
- Support manual fan control and "custom" thermal profile
- amd/hsmp:
- Add sysfs files to show HSMP telemetry
- Report power readings and limits via hwmon
- amd/isp4: Add AMD ISP platform config for OV05C10
- asus-wmi:
- Refactor Ally suspend/resume to work better with older FW
- hid-asus: check ROG Ally MCU version and warn about old FW versions
- dasharo-acpi:
- Add driver for Dasharo devices supporting fans and temperatures
monitoring
- dell-ddv:
- Expose the battery health and manufacture date to userspace
using power supply extensions
- Implement the battery matching algorithm
- dell-pc:
- Improve error propagation
- Use faux device
- int3472:
- Add delays to avoid GPIO regulator spikes
- Add handshake pin support
- Make regulator supply name configurable and allow registering
more than 1 GPIO regulator
- Map mt9m114 powerdown pin to powerenable
- intel/pmc: Add separate SSRAM Telemetry driver
- intel-uncore-freq: Add attributes to show agent types and die ID
- ISST:
- Support SST-TF revision 2 (allows more cores per bucket)
- Support SST-PP revision 2 (fabric 1 frequencies)
- Remove unnecessary SST MSRs restore (the package retains MSRs
despite CPU offlining)
- mellanox: Add support for SN2201, SN4280, SN5610, and SN5640
- mellanox: mlxbf-pmc: Support additional PMC blocks
- oxpec:
- Add OneXFly variants
- Add support for charge limit, charge thresholds, and turbo LED
- Distinguish current X1 variants to avoid unwanted matching to
new variants
- Follow hwmon conventions
- Move from hwmon/oxp-sensors to platform/x86 to match the
enlarged scope
- power supply:
- Add inhibit-charge-awake (needed by oxpec)
- Add additional battery health status values ("blown fuse" and
"cell imbalance") (needed by dell-ddv)
- powerwell-ec: Add driver for Portwell EC supporting GPIO and watchdog
- thinkpad-acpi: Support camera shutter switch hotkey
- tuxedo: Add virtual LampArray for TUXEDO NB04 devices
- tools/power/x86/intel-speed-select:
- Support displaying SST-PP revision 2 fields
- Skip uncore frequency update on newer generations of CPUs
- Miscellaneous cleanups / refactoring / improvements"
* tag 'platform-drivers-x86-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (112 commits)
thermal/drivers/acerhdf: Constify struct thermal_zone_device_ops
platform/x86/amd/hsmp: fix building with CONFIG_HWMON=m
platform/x86: asus-wmi: fix build without CONFIG_SUSPEND
docs: ABI: Fix "aassociated" to "associated"
platform/x86: Add AMD ISP platform config for OV05C10
Documentation: admin-guide: pm: Add documentation for die_id
platform/x86/intel-uncore-freq: Add attributes to show die_id
platform/x86/intel: power-domains: Add interface to get Linux die ID
Documentation: admin-guide: pm: Add documentation for agent_types
platform/x86/intel-uncore-freq: Add attributes to show agent types
platform/x86/tuxedo: Prevent invalid Kconfig state
platform/x86: dell-ddv: Expose the battery health to userspace
platform/x86: dell-ddv: Expose the battery manufacture date to userspace
platform/x86: dell-ddv: Implement the battery matching algorithm
power: supply: core: Add additional health status values
platform/x86/amd/hsmp: acpi: Add sysfs files to display HSMP telemetry
platform/x86/amd/hsmp: Report power via hwmon sensors
platform/x86/amd/hsmp: Use a single DRIVER_VERSION for all hsmp modules
platform/mellanox: mlxreg-dpu: Fix smatch warnings
platform: mellanox: nvsw-sn2200: Fix .items in nvsw_sn2201_busbar_hotplug
...
- Fix potential division-by-zero error in em_compute_costs() (Yaxiong
Tian).
- Fix typos in energy model documentation and example driver code (Moon
Hee Lee, Atul Kumar Pant).
- Rearrange the energy model management code and add a new function for
adjusting a CPU energy model after adjusting the capacity of the
given CPU to it (Rafael Wysocki).
- Refactor cpufreq_online(), add and use cpufreq policy locking guards,
use __free() in policy reference counting, and clean up core cpufreq
code on top of that (Rafael Wysocki).
- Fix boost handling on CPU suspend/resume and sysfs updates (Viresh
Kumar).
- Fix des_perf clamping with max_perf in amd_pstate_update() (Dhananjay
Ugwekar).
- Add offline, online and suspend callbacks to the amd-pstate driver,
rename and use the existing amd_pstate_epp callbacks in it (Dhananjay
Ugwekar).
- Add support for the "Requested CPU Min frequency" BIOS option to the
amd-pstate driver (Dhananjay Ugwekar).
- Reset amd-pstate driver mode after running selftests (Swapnil
Sapkal).
- Avoid shadowing ret in amd_pstate_ut_check_driver() (Nathan
Chancellor).
- Add helper for governor checks to the schedutil cpufreq governor and
move cpufreq-specific EAS checks to cpufreq (Rafael Wysocki).
- Populate the cpu_capacity sysfs entries from the intel_pstate driver
after registering asym capacity support (Ricardo Neri).
- Add support for enabling Energy-aware scheduling (EAS) to the
intel_pstate driver when operating in the passive mode on a hybrid
platform (Rafael Wysocki).
- Drop redundant cpus_read_lock() from store_local_boost() in the
cpufreq core (Seyediman Seyedarab).
- Replace sscanf() with kstrtouint() in the cpufreq code and use a
symbol instead of a raw number in it (Bowen Yu).
- Add support for autonomous CPU performance state selection to the
CPPC cpufreq driver (Lifeng Zheng).
- OPP: Add dev_pm_opp_set_level() (Praveen Talari).
- Introduce scope-based cleanup headers and mutex locking guards in OPP
core (Viresh Kumar).
- Switch OPP to use kmemdup_array() (Zhang Enpei).
- Optimize bucket assignment when next_timer_ns equals KTIME_MAX in the
menu cpuidle governor (Zhongqiu Han).
- Convert the cpuidle PSCI driver to a faux device one (Sudeep Holla).
- Add C1 demotion on/off sysfs knob to the intel_idle driver (Artem
Bityutskiy).
- Fix typos in two comments in the teo cpuidle governor (Atul Kumar
Pant).
- Fix denying of auto suspend in pm_suspend_timer_fn() (Charan Teja
Kalla).
- Move debug runtime PM attributes to runtime_attrs[] (Rafael Wysocki).
- Add new devm_ functions for enabling runtime PM and runtime PM
reference counting (Bence Csókás).
- Remove size arguments from strscpy() calls in the hibernation core
code (Thorsten Blum).
- Adjust the handling of devices with asynchronous suspend enabled
during system suspend and resume to start resuming them immediately
after resuming their parents and to start suspending such a device
immediately after suspending its first child (Rafael Wysocki).
- Adjust messages printed during tasks freezing to avoid using
pr_cont() (Andrew Sayers, Paul Menzel).
- Clean up unnecessary usage of !! in pm_print_times_init() (Zihuan
Zhang).
- Add missing wakeup source attribute relax_count to sysfs and
remove the space character at the end ofi the string produced by
pm_show_wakelocks() (Zijun Hu).
- Add configurable pm_test delay for hibernation (Zihuan Zhang).
- Disable asynchronous suspend in ucsi_ccg_probe() to prevent the
cypd4226 device on Tegra boards from suspending prematurely (Jon
Hunter).
- Unbreak printing PM debug messages during hibernation and clean up
some related code (Rafael Wysocki).
- Add a systemd service to run cpupower and change cpupower binding's
Makefile to use -lcpupower (John B. Wyatt IV, Francesco Poli).
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmg0xS0SHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1AwwH/Rvgza5YBPb9JZqWJT/ZiBw7HcEWHhP1
fNfcVU1gXPZiF0yoPfjfJua6BcLj6lyQ3d/+zWqqAcWfmRSD6HPe8yYz8qALUAqj
RWhDa04aGj6B9bQuOjejatznYlQlkwCRT7zec+75D+dAHVMqR/Vt2LFAetCadgHe
MQibAQmVFXu3RFkBjReTAdGzVoTXkwoZDrzdfA2aFAfMJNtJpOW4atUZvnucuctv
VK3ZratrctCIw7yXEoB1nWSmlY7R5JlslplBfndjmmOnky3YxNr7C6paqwtbTWoF
MiX48qkmLOGeO6gS8s/lVCDQ4oZ+UNFQvXRsM5NGjycBikhHX/dp/w4=
=dIqJ
-----END PGP SIGNATURE-----
Merge tag 'pm-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Once again, the changes are dominated by cpufreq updates, but this
time the majority of them are cpufreq core changes, mostly related to
the introduction of policy locking guards and __free() usage, and
fixes related to boost handling.
Still, there is also a significant update of the intel_pstate driver
making it register an energy model when running on a hybrid platform
which is used for enabling energy-aware scheduling (EAS) if the driver
operates in the passive mode (and schedutil is used as the cpufreq
governor for all CPUs which is the passive mode default).
There are some amd-pstate driver updates too, for a good measure,
including the "Requested CPU Min frequency" BIOS option support and
new online/offline callbacks.
In the cpuidle space, the most significant change is the addition of a
C1 demotion on/off sysfs knob to intel_idle which should help some
users to configure their systems more precisely. There is also the
conversion of the PSCI cpuidle driver to a faux device one and there
are two small updates of cpuidle governors.
Device power management is also modified quite a bit, especially the
handling of devices with asynchronous suspend and resume enabled
during system transitions. They are now going to be handled more
asynchronously during suspend transitions and somewhat less
aggressively during resume transitions.
Apart from the above, the operating performance points (OPP) library
is now going to use mutex locking guards and scope-based cleanup
helpers and there is the usual bunch of assorted fixes and code
cleanups.
Specifics:
- Fix potential division-by-zero error in em_compute_costs() (Yaxiong
Tian)
- Fix typos in energy model documentation and example driver code
(Moon Hee Lee, Atul Kumar Pant)
- Rearrange the energy model management code and add a new function
for adjusting a CPU energy model after adjusting the capacity of
the given CPU to it (Rafael Wysocki)
- Refactor cpufreq_online(), add and use cpufreq policy locking
guards, use __free() in policy reference counting, and clean up
core cpufreq code on top of that (Rafael Wysocki)
- Fix boost handling on CPU suspend/resume and sysfs updates (Viresh
Kumar)
- Fix des_perf clamping with max_perf in amd_pstate_update()
(Dhananjay Ugwekar)
- Add offline, online and suspend callbacks to the amd-pstate driver,
rename and use the existing amd_pstate_epp callbacks in it
(Dhananjay Ugwekar)
- Add support for the "Requested CPU Min frequency" BIOS option to
the amd-pstate driver (Dhananjay Ugwekar)
- Reset amd-pstate driver mode after running selftests (Swapnil
Sapkal)
- Avoid shadowing ret in amd_pstate_ut_check_driver() (Nathan
Chancellor)
- Add helper for governor checks to the schedutil cpufreq governor
and move cpufreq-specific EAS checks to cpufreq (Rafael Wysocki)
- Populate the cpu_capacity sysfs entries from the intel_pstate
driver after registering asym capacity support (Ricardo Neri)
- Add support for enabling Energy-aware scheduling (EAS) to the
intel_pstate driver when operating in the passive mode on a hybrid
platform (Rafael Wysocki)
- Drop redundant cpus_read_lock() from store_local_boost() in the
cpufreq core (Seyediman Seyedarab)
- Replace sscanf() with kstrtouint() in the cpufreq code and use a
symbol instead of a raw number in it (Bowen Yu)
- Add support for autonomous CPU performance state selection to the
CPPC cpufreq driver (Lifeng Zheng)
- OPP: Add dev_pm_opp_set_level() (Praveen Talari)
- Introduce scope-based cleanup headers and mutex locking guards in
OPP core (Viresh Kumar)
- Switch OPP to use kmemdup_array() (Zhang Enpei)
- Optimize bucket assignment when next_timer_ns equals KTIME_MAX in
the menu cpuidle governor (Zhongqiu Han)
- Convert the cpuidle PSCI driver to a faux device one (Sudeep Holla)
- Add C1 demotion on/off sysfs knob to the intel_idle driver (Artem
Bityutskiy)
- Fix typos in two comments in the teo cpuidle governor (Atul Kumar
Pant)
- Fix denying of auto suspend in pm_suspend_timer_fn() (Charan Teja
Kalla)
- Move debug runtime PM attributes to runtime_attrs[] (Rafael
Wysocki)
- Add new devm_ functions for enabling runtime PM and runtime PM
reference counting (Bence Csókás)
- Remove size arguments from strscpy() calls in the hibernation core
code (Thorsten Blum)
- Adjust the handling of devices with asynchronous suspend enabled
during system suspend and resume to start resuming them immediately
after resuming their parents and to start suspending such a device
immediately after suspending its first child (Rafael Wysocki)
- Adjust messages printed during tasks freezing to avoid using
pr_cont() (Andrew Sayers, Paul Menzel)
- Clean up unnecessary usage of !! in pm_print_times_init() (Zihuan
Zhang)
- Add missing wakeup source attribute relax_count to sysfs and remove
the space character at the end ofi the string produced by
pm_show_wakelocks() (Zijun Hu)
- Add configurable pm_test delay for hibernation (Zihuan Zhang)
- Disable asynchronous suspend in ucsi_ccg_probe() to prevent the
cypd4226 device on Tegra boards from suspending prematurely (Jon
Hunter)
- Unbreak printing PM debug messages during hibernation and clean up
some related code (Rafael Wysocki)
- Add a systemd service to run cpupower and change cpupower binding's
Makefile to use -lcpupower (John B. Wyatt IV, Francesco Poli)"
* tag 'pm-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
cpufreq: CPPC: Add support for autonomous selection
cpufreq: Update sscanf() to kstrtouint()
cpufreq: Replace magic number
OPP: switch to use kmemdup_array()
PM: freezer: Rewrite restarting tasks log to remove stray *done.*
PM: runtime: fix denying of auto suspend in pm_suspend_timer_fn()
cpufreq: drop redundant cpus_read_lock() from store_local_boost()
cpupower: do not install files to /etc/default/
cpupower: do not call systemctl at install time
cpupower: do not write DESTDIR to cpupower.service
PM: sleep: Introduce pm_sleep_transition_in_progress()
cpufreq/amd-pstate: Avoid shadowing ret in amd_pstate_ut_check_driver()
cpufreq: intel_pstate: Document hybrid processor support
cpufreq: intel_pstate: EAS: Increase cost for CPUs using L3 cache
cpufreq: intel_pstate: EAS support for hybrid platforms
PM: EM: Introduce em_adjust_cpu_capacity()
PM: EM: Move CPU capacity check to em_adjust_new_capacity()
PM: EM: Documentation: Fix typos in example driver code
cpufreq: Drop policy locking from cpufreq_policy_is_good_for_eas()
PM: sleep: Introduce pm_suspend_in_progress()
...
Merge cpuidle updates for 6.16-rc1:
- Optimize bucket assignment when next_timer_ns equals KTIME_MAX in the
menu cpuidle governor (Zhongqiu Han).
- Convert the cpuidle PSCI driver to a faux device one (Sudeep Holla).
- Add C1 demotion on/off sysfs knob to the intel_idle driver (Artem
Bityutskiy).
- Fix typos in two comments in the teo cpuidle governor (Atul Kumar
Pant).
* pm-cpuidle:
cpuidle: psci: Avoid initializing faux device if no DT idle states are present
Documentation: ABI: testing: document the new cpuidle sysfs file
Documentation: admin-guide: pm: Document intel_idle C1 demotion
intel_idle: Add C1 demotion on/off sysfs knob
cpuidle: psci: Transition to the faux device interface
cpuidle: menu: Optimize bucket assignment when next_timer_ns equals KTIME_MAX
cpuidle: teo: Fix typos in two comments
Describe the support for hybrid processors in intel_pstate, including
the CAS and EAS support, in the admin-guide documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/1935040.CQOukoFCf9@rjwysocki.net
Change a few words and abbreviations/punctuation.
Change one echo command to include a trailing '`'.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250405001447.4039463-1-rdunlap@infradead.org
- Manage sysfs attributes and boost frequencies efficiently from
cpufreq core to reduce boilerplate code in drivers (Viresh Kumar).
- Minor cleanups to cpufreq drivers (Aaron Kling, Benjamin Schneider,
Dhananjay Ugwekar, Imran Shaik, zuoqian).
- Migrate some cpufreq drivers to using for_each_present_cpu() (Jacky
Bai).
- cpufreq-qcom-hw DT binding fixes (Krzysztof Kozlowski).
- Use str_enable_disable() helper in cpufreq_online() (Lifeng Zheng).
- Optimize the amd-pstate driver to avoid cases where call paths end
up calling the same writes multiple times and needlessly caching
variables through code reorganization, locking overhaul and tracing
adjustments (Mario Limonciello, Dhananjay Ugwekar).
- Make it possible to avoid enabling capacity-aware scheduling (CAS) in
the intel_pstate driver and relocate a check for out-of-band (OOB)
platform handling in it to make it detect OOB before checking HWP
availability (Rafael Wysocki).
- Fix dbs_update() to avoid inadvertent conversions of negative integer
values to unsigned int which causes CPU frequency selection to be
inaccurate in some cases when the "conservative" cpufreq governor is
in use (Jie Zhan).
- Update the handling of the most recent idle intervals in the menu
cpuidle governor to prevent useful information from being discarded
by it in some cases and improve the prediction accuracy (Rafael
Wysocki).
- Make it possible to tell the intel_idle driver to ignore its built-in
table of idle states for the given processor, clean up the handling
of auto-demotion disabling on Baytrail and Cherrytrail chips in it,
and update its MAINTAINERS entry (David Arcari, Artem Bityutskiy,
Rafael Wysocki).
- Make some cpuidle drivers use for_each_present_cpu() instead of
for_each_possible_cpu() during initialization to avoid issues
occurring when nosmp or maxcpus=0 are used (Jacky Bai).
- Clean up the Energy Model handling code somewhat (Rafael Wysocki).
- Use kfree_rcu() to simplify the handling of runtime Energy Model
updates (Li RongQing).
- Add an entry for the Energy Model framework to MAINTAINERS as
properly maintained (Lukasz Luba).
- Address RCU-related sparse warnings in the Energy Model code (Rafael
Wysocki).
- Remove ENERGY_MODEL dependency on SMP and allow it to be selected
when DEVFREQ is set without CPUFREQ so it can be used on a wider
range of systems (Jeson Gao).
- Unify error handling during runtime suspend and runtime resume in the
core to help drivers to implement more consistent runtime PM error
handling (Rafael Wysocki).
- Drop a redundant check from pm_runtime_force_resume() and rearrange
documentation related to __pm_runtime_disable() (Rafael Wysocki).
- Rework the handling of the "smart suspend" driver flag in the PM core
to avoid issues hat may occur when drivers using it depend on some
other drivers and clean up the related PM core code (Rafael Wysocki,
Colin Ian King).
- Fix the handling of devices with the power.direct_complete flag set
if device_suspend() returns an error for at least one device to avoid
situations in which some of them may not be resumed (Rafael Wysocki).
- Use mutex_trylock() in hibernate_compressor_param_set() to avoid a
possible deadlock that may occur if the "compressor" hibernation
module parameter is accessed during the registration of a new
ieee80211 device (Lizhi Xu).
- Suppress sleeping parent warning in device_pm_add() in the case when
new children are added under a device with the power.direct_complete
set after it has been processed by device_resume() (Xu Yang).
- Remove needless return in three void functions related to system
wakeup (Zijun Hu).
- Replace deprecated kmap_atomic() with kmap_local_page() in the
hibernation core code (David Reaver).
- Remove unused helper functions related to system sleep (David Alan
Gilbert).
- Clean up s2idle_enter() so it does not lock and unlock CPU offline
in vain and update comments in it (Ulf Hansson).
- Clean up broken white space in dpm_wait_for_children() (Geert
Uytterhoeven).
- Update the cpupower utility to fix lib version-ing in it and memory
leaks in error legs, remove hard-coded values, and implement CPU
physical core querying (Thomas Renninger, John B. Wyatt IV, Shuah
Khan, Yiwei Lin, Zhongqiu Han).
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmfhhTYSHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO16/gIAKuRiG1fFgUcUSXC1iFu42vrB/1i4wpA
02GICACqM3K6/5jd3ct/WOU28GUgDs+xcmqH7CnMaM6y9nXEWjWarmSfFekAO+0q
TPtQ7xTy0hBCB3he1P2uLKBJBin4Wn47U9/rvs4J7mQd5zDxTINKIiVoHg2lEE+s
HAeSoNRb2sp5IZDm9+/LfhHNYRP1mJ97cbZlymqctGB3xgDL7qMLid/1+gFPHAQS
4/LXj3IgyU8DpA/j5nhtpaAqjN5g2QxIUfQgADRIcESK99Y/7aAMs1/G0WhJKaay
9yx+4/xmkGvVCZQx1DphksFLISEzltY0SFWLsoppPzBTGVEW2GQQsNI=
=LqVy
-----END PGP SIGNATURE-----
Merge tag 'pm-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are dominated by cpufreq updates which in turn are dominated by
updates related to boost support in the core and drivers and
amd-pstate driver optimizations.
Apart from the above, there are some cpuidle updates including a
rework of the most recent idle intervals handling in the venerable
menu governor that leads to significant improvements in some
performance benchmarks, as the governor is now more likely to predict
a shorter idle duration in some cases, and there are updates of the
core device power management code, mostly related to system suspend
and resume, that should help to avoid potential issues arising when
the drivers of devices depending on one another want to use different
optimizations.
There is also a usual collection of assorted fixes and cleanups,
including removal of some unused code.
Specifics:
- Manage sysfs attributes and boost frequencies efficiently from
cpufreq core to reduce boilerplate code in drivers (Viresh Kumar)
- Minor cleanups to cpufreq drivers (Aaron Kling, Benjamin Schneider,
Dhananjay Ugwekar, Imran Shaik, zuoqian)
- Migrate some cpufreq drivers to using for_each_present_cpu() (Jacky
Bai)
- cpufreq-qcom-hw DT binding fixes (Krzysztof Kozlowski)
- Use str_enable_disable() helper in cpufreq_online() (Lifeng Zheng)
- Optimize the amd-pstate driver to avoid cases where call paths end
up calling the same writes multiple times and needlessly caching
variables through code reorganization, locking overhaul and tracing
adjustments (Mario Limonciello, Dhananjay Ugwekar)
- Make it possible to avoid enabling capacity-aware scheduling (CAS)
in the intel_pstate driver and relocate a check for out-of-band
(OOB) platform handling in it to make it detect OOB before checking
HWP availability (Rafael Wysocki)
- Fix dbs_update() to avoid inadvertent conversions of negative
integer values to unsigned int which causes CPU frequency selection
to be inaccurate in some cases when the "conservative" cpufreq
governor is in use (Jie Zhan)
- Update the handling of the most recent idle intervals in the menu
cpuidle governor to prevent useful information from being discarded
by it in some cases and improve the prediction accuracy (Rafael
Wysocki)
- Make it possible to tell the intel_idle driver to ignore its
built-in table of idle states for the given processor, clean up the
handling of auto-demotion disabling on Baytrail and Cherrytrail
chips in it, and update its MAINTAINERS entry (David Arcari, Artem
Bityutskiy, Rafael Wysocki)
- Make some cpuidle drivers use for_each_present_cpu() instead of
for_each_possible_cpu() during initialization to avoid issues
occurring when nosmp or maxcpus=0 are used (Jacky Bai)
- Clean up the Energy Model handling code somewhat (Rafael Wysocki)
- Use kfree_rcu() to simplify the handling of runtime Energy Model
updates (Li RongQing)
- Add an entry for the Energy Model framework to MAINTAINERS as
properly maintained (Lukasz Luba)
- Address RCU-related sparse warnings in the Energy Model code
(Rafael Wysocki)
- Remove ENERGY_MODEL dependency on SMP and allow it to be selected
when DEVFREQ is set without CPUFREQ so it can be used on a wider
range of systems (Jeson Gao)
- Unify error handling during runtime suspend and runtime resume in
the core to help drivers to implement more consistent runtime PM
error handling (Rafael Wysocki)
- Drop a redundant check from pm_runtime_force_resume() and rearrange
documentation related to __pm_runtime_disable() (Rafael Wysocki)
- Rework the handling of the "smart suspend" driver flag in the PM
core to avoid issues hat may occur when drivers using it depend on
some other drivers and clean up the related PM core code (Rafael
Wysocki, Colin Ian King)
- Fix the handling of devices with the power.direct_complete flag set
if device_suspend() returns an error for at least one device to
avoid situations in which some of them may not be resumed (Rafael
Wysocki)
- Use mutex_trylock() in hibernate_compressor_param_set() to avoid a
possible deadlock that may occur if the "compressor" hibernation
module parameter is accessed during the registration of a new
ieee80211 device (Lizhi Xu)
- Suppress sleeping parent warning in device_pm_add() in the case
when new children are added under a device with the
power.direct_complete set after it has been processed by
device_resume() (Xu Yang)
- Remove needless return in three void functions related to system
wakeup (Zijun Hu)
- Replace deprecated kmap_atomic() with kmap_local_page() in the
hibernation core code (David Reaver)
- Remove unused helper functions related to system sleep (David Alan
Gilbert)
- Clean up s2idle_enter() so it does not lock and unlock CPU offline
in vain and update comments in it (Ulf Hansson)
- Clean up broken white space in dpm_wait_for_children() (Geert
Uytterhoeven)
- Update the cpupower utility to fix lib version-ing in it and memory
leaks in error legs, remove hard-coded values, and implement CPU
physical core querying (Thomas Renninger, John B. Wyatt IV, Shuah
Khan, Yiwei Lin, Zhongqiu Han)"
* tag 'pm-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (139 commits)
PM: sleep: Fix bit masking operation
dt-bindings: cpufreq: cpufreq-qcom-hw: Narrow properties on SDX75, SA8775p and SM8650
dt-bindings: cpufreq: cpufreq-qcom-hw: Drop redundant minItems:1
dt-bindings: cpufreq: cpufreq-qcom-hw: Add missing constraint for interrupt-names
dt-bindings: cpufreq: cpufreq-qcom-hw: Add QCS8300 compatible
cpufreq: Init cpufreq only for present CPUs
PM: sleep: Fix handling devices with direct_complete set on errors
cpuidle: Init cpuidle only for present CPUs
PM: clk: Remove unused pm_clk_remove()
PM: sleep: core: Fix indentation in dpm_wait_for_children()
PM: s2idle: Extend comment in s2idle_enter()
PM: s2idle: Drop redundant locks when entering s2idle
PM: sleep: Remove unused pm_generic_ wrappers
cpufreq: tegra186: Share policy per cluster
cpupower: Make lib versioning scheme more obvious and fix version link
PM: EM: Rework the depends on for CONFIG_ENERGY_MODEL
PM: EM: Address RCU-related sparse warnings
cpupower: Implement CPU physical core querying
pm: cpupower: remove hard-coded topology depth values
pm: cpupower: Fix cmd_monitor() error legs to free cpu_topology
...
Merge cpuidle updates for 6.15-rc5, including a menu governor update
that is reported to improve some benchmark results quite significantly:
- Update the handling of the most recent idle intervals in the menu
cpuidle governor to prevent useful information from being discarded
by it in some cases and improve the prediction accuracy (Rafael
Wysocki).
- Make it possible to tell the intel_idle driver to ignore its built-in
table of idle states for the given processor, clean up the handling
of auto-demotion disabling on Baytrail and Cherrytrail chips in it,
and update its MAINTAINERS entry (David Arcari, Artem Bityutskiy,
Rafael Wysocki).
- Make some cpuidle drivers use for_each_present_cpu() instead of
for_each_possible_cpu() during initialization to avoid issues
occurring when nosmp or maxcpus=0 are used (Jacky Bai).
* pm-cpuidle:
cpuidle: Init cpuidle only for present CPUs
cpuidle: intel_idle: Update MAINTAINERS
intel_idle: introduce 'no_native' module parameter
cpuidle: menu: Update documentation after get_typical_interval() changes
cpuidle: menu: Avoid discarding useful information
cpuidle: menu: Eliminate outliers on both ends of the sample set
cpuidle: menu: Tweak threshold use in get_typical_interval()
cpuidle: menu: Use one loop for average and variance computations
cpuidle: menu: Drop a redundant local variable
intel_idle: clean up BYT/CHT auto demotion disable
This work had been triggered by a report that commit 0611a640e6
("eventpoll: prefer kfree_rcu() in __ep_remove()") had caused the
critical-jOPS metric of the SPECjbb 2015 benchmark [1] to drop by around
50% even though it generally reduced kernel overhead. Indeed, it was
found during further investigation that the total interrupt rate while
running the SPECjbb workload had fallen as a result of that commit by
55% and the local timer interrupt rate had fallen by almost 80%.
That turned out to cause the menu cpuidle governor to select the deepest
idle state supplied by the cpuidle driver (intel_idle) much more often
which added significantly more idle state latency to the workload and
that led to the decrease of the critical-jOPS score.
Interestingly enough, this problem was not visible when the teo cpuidle
governor was used instead of menu, so it appeared to be specific to the
latter. CPU wakeup event statistics collected while running the
workload indicated that the menu governor was effectively ignoring non-
timer wakeup information and all of its idle state selection decisions
appeared to be based on timer wakeups only. Thus, it appeared that the
reduction of the local timer interrupt rate caused the governor to
predict a idle duration much more often while running the workload and
the deepest idle state was selected significantly more often as a result
of that.
A subsequent inspection of the get_typical_interval() function in the
menu governor indicated that it might return UINT_MAX too often which
then caused the governor's decisions to be based entirely on information
related to timers.
Generally speaking, UINT_MAX is returned by get_typical_interval() if it
cannot make a prediction based on the most recent idle intervals data
with sufficiently high confidence, but at least in some cases this means
that useful information is not taken into account at all which may lead
to significant idle state selection mistakes. Moreover, this is not
really unlikely to happen.
One issue with get_typical_interval() is that, when it eliminates
outliers from the sample set in an attempt to reduce the standard
deviation (and so improve the prediction confidence), it does that by
dropping high-end samples only, while samples at the low end of the set
are retained. However, the samples at the low end very well may be the
outliers and they should be eliminated from the sample set instead of
the high-end samples. Accordingly, the likelihood of making a
meaningful idle duration prediction can be improved by making it also
eliminate low-end samples if they are farther from the average than
high-end samples.
Another issue is that get_typical_interval() gives up after eliminating
1/4 of the samples if the standard deviation is still not as low as
desired (within 1/6 of the average or within 20 us if the average is
close to 0), but the remaining samples in the set still represent useful
information at that point and discarding them altogether may lead to
suboptimal idle state selection.
For instance, the largest idle duration value in the get_typical_interval()
data set is the maximum idle duration observed recently and it is likely
that the upcoming idle duration will not exceed it. Therefore, in the
absence of a better choice, this value can be used as an upper bound on
the target residency of the idle state to select.
* cpuidle-menu:
cpuidle: menu: Update documentation after get_typical_interval() changes
cpuidle: menu: Avoid discarding useful information
cpuidle: menu: Eliminate outliers on both ends of the sample set
cpuidle: menu: Tweak threshold use in get_typical_interval()
cpuidle: menu: Use one loop for average and variance computations
cpuidle: menu: Drop a redundant local variable
Since commit 18734958e9 ("intel_idle: Use ACPI _CST for processor models
without C-state tables") the intel_idle driver has had the ability to use
the ACPI _CST to populate C-states when the processor model is not
recognized.
However, even when the processor model is recognized (native mode) there
are cases where it is useful to make the driver ignore the per-CPU idle
states in lieu of ACPI C-states (such as specific application performance).
Add a new 'no_native' module parameter to provide this functionality.
Signed-off-by: David Arcari <darcari@redhat.com>
Link: https://patch.msgid.link/20250220151120.1131122-1-darcari@redhat.com
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ rjw: Spell CPU in capitals ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The documentation of the menu cpuidle governor needs to be updated
to match the code behavior after some changes made recently.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/4998484.31r3eYUQgx@rjwysocki.net
[ rjw: More specific subject, two typos fixed in the changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Capacity-aware scheduling (CAS) is enabled by default by intel_pstate on
hybrid systems without SMT, but in some usage scenarios it may be more
attractive to place tasks for maximum CPU performance regardless of the
extra cost in terms of energy, which is the case on such systems when
CAS is not enabled, so introduce a command line option to forbid
intel_pstate to enable CAS.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by:Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/2781262.mvXUDI8C0e@rjwysocki.net
Currently the CPUFreq core exposes two sysfs attributes that can be used
to query current frequency of a given CPU(s): namely cpuinfo_cur_freq
and scaling_cur_freq. Both provide slightly different view on the
subject and they do come with their own drawbacks.
cpuinfo_cur_freq provides higher precision though at a cost of being
rather expensive. Moreover, the information retrieved via this attribute
is somewhat short lived as frequency can change at any point of time
making it difficult to reason from.
scaling_cur_freq, on the other hand, tends to be less accurate but then
the actual level of precision (and source of information) varies between
architectures making it a bit ambiguous.
The new attribute, cpuinfo_avg_freq, is intended to provide more stable,
distinct interface, exposing an average frequency of a given CPU(s), as
reported by the hardware, over a time frame spanning no more than a few
milliseconds. As it requires appropriate hardware support, this
interface is optional.
Note that under the hood, the new attribute relies on the information
provided by arch_freq_get_on_cpu, which, up to this point, has been
feeding data for scaling_cur_freq attribute, being the source of
ambiguity when it comes to interpretation. This has been amended by
restoring the intended behavior for scaling_cur_freq, with a new
dedicated config option to maintain status quo for those, who may need
it.
CC: Jonathan Corbet <corbet@lwn.net>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: Borislav Petkov <bp@alien8.de>
CC: Dave Hansen <dave.hansen@linux.intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Phil Auld <pauld@redhat.com>
CC: x86@kernel.org
CC: linux-doc@vger.kernel.org
Signed-off-by: Beata Michalska <beata.michalska@arm.com>
Reviewed-by: Prasanna Kumar T S M <ptsm@linux.microsoft.com>
Reviewed-by: Sumit Gupta <sumitg@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20250131162439.3843071-3-beata.michalska@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
After commit 38f83090f5 ("cpuidle: menu: Remove iowait influence") and
other previous changes, the description of the menu governor in the
documentation does not match the code any more, so update it as
appropriate.
Fixes: 38f83090f5 ("cpuidle: menu: Remove iowait influence")
Fixes: 5484e31bbb ("cpuidle: menu: Skip tick_nohz_get_sleep_length() call in some cases")
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/12589281.O9o76ZdvQC@rjwysocki.net
commit ad4caad58d ("cpufreq: amd-pstate: Merge
amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
changed the semantics for highest perf and commit 18d9b52271
("cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled")
worked around those semantic changes.
This however is a confusing result and furthermore makes it awkward to
change frequency limits and boost due to the scaling differences. Restore
the boost numerator to highest perf again.
Suggested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Fixes: ad4caad58d ("cpufreq: amd-pstate: Merge amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
Link: https://lore.kernel.org/r/20241209185248.16301-2-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
There were two changes related to transition latency recently.
Namely commit e13aa799c2 ("cpufreq: Change default transition delay
to 2ms") and
commit 37c6dccd68 ("cpufreq: Remove LATENCY_MULTIPLIER").
Both changed the defaults / maximums so let the documentation
reflect that.
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/46853b6e-bad5-4ace-9b23-ff157f234ae3@arm.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Highlights:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software properties
- bunch of small cleanups, fixes, hw-id additions, etc.
The following is an automated git shortlog grouped by driver:
Documentation:
- admin-guide: pm: Add efficiency vs. latency tradeoff to uncore documentation
ISST:
- Simplify isst_misc_reg() and isst_misc_unreg()
MAINTAINERS:
- adjust file entry in INTEL MID PLATFORM
- Add Intel MID section
Merge tag 'hwmon-for-v6.11-rc7' into review-hans:
- Merge tag 'hwmon-for-v6.11-rc7' into review-hans
Merge tag 'platform-drivers-x86-v6.11-3' into review-hans:
- Merge tag 'platform-drivers-x86-v6.11-3' into review-hans
acer-wmi:
- Use backlight power constants
asus-laptop:
- Use backlight power constants
asus-nb-wmi:
- Use backlight power constants
asus-wmi:
- don't fail if platform_profile already registered
- add debug print in more key places
- Use backlight power constants
- add support for vivobook fan profiles
dell-laptop:
- remove duplicate code w/ battery function
- Add knobs to change battery charge settings
dt-bindings:
- platform: Add Surface System Aggregator Module
- serial: Allow embedded-controller as child node
eeepc-laptop:
- Use backlight power constants
eeepc-wmi:
- Use backlight power constants
fujitsu-laptop:
- Use backlight power constants
hid-asus:
- use hid for brightness control on keyboard
ideapad-laptop:
- Make the scope_guard() clear of its scope
- move ACPI helpers from header to source file
- Use backlight power constants
int3472:
- Use str_high_low()
- Use GPIO_LOOKUP() macro
- make common part a separate module
intel-hid:
- Use string_choices API instead of ternary operator
intel/pmc:
- Ignore all LTRs during suspend
- Remove unused param idx from pmc_for_each_mode()
intel_scu_ipc:
- Move intel_scu_ipc.h out of arch/x86/include/asm
intel_scu_wdt:
- Move intel_scu_wdt.h to x86 subfolder
lenovo-ymc:
- Ignore the 0x0 state
lg-laptop:
- Add operation region support
oaktrail:
- Use backlight power constants
panasonic-laptop:
- Add support for programmable buttons
platform/mellanox:
- mlxbf-pmc: fix lockdep warning
platform/olpc:
- Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/surface:
- Add OF support
platform/x86/amd:
- pmf: Add quirk for TUF Gaming A14
platform/x86/amd/pmf:
- Update SMU metrics table for 1AH family series
- Relocate CPU ID macros to the PMF header
- Add support for notifying Smart PC Solution updates
platform/x86/intel-uncore-freq:
- Add efficiency latency control to sysfs interface
- Add support for efficiency latency control
- Do not present separate package-die domain
platform/x86/intel/ifs:
- Fix SBAF title underline length
- Add SBAF test support
- Add SBAF test image loading support
- Refactor MSR usage in IFS test code
platform/x86/intel/pmc:
- Show live substate requirements
platform/x86/intel/pmt:
- Use PMT callbacks
platform/x86/intel/vsec:
- Add PMT read callbacks
platform/x86/intel/vsec.h:
- Move to include/linux
samsung-laptop:
- Use backlight power constants
serial-multi-instantiate:
- Don't require both I2C and SPI
thinkpad_acpi:
- Fix uninitialized symbol 's' warning
- Add Thinkpad Edge E531 fan support
touchscreen_dmi:
- add nanote-next quirk
trace:
- platform/x86/intel/ifs: Add SBAF trace support
wmi:
- Call both legacy and WMI driver notify handlers
- Merge get_event_data() with wmi_get_notify_data()
- Remove wmi_get_event_data()
- Pass event data directly to legacy notify handlers
x86-android-tablets:
- Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
- Fix spelling in the comments
x86/platform/geode:
- switch GPIO buttons and LEDs to software properties
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmbq2tYUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9xKYAgAoXZt1MjBDA1mP813i4bj8CYQHWO+
YnugVhEccucxgC6sBGzQeRLBNuG/VaBN6tyJ1pKYMpWV5gSthq1Iop+DZbno2ciM
QAnSSzioHB/dhYBXuKmZatkMsKLjLjtfcexUed9DfwKapqFl3XQMb6cEYasM37hH
197K4yAFF3oqQImlACwQDxN1q3eCG6bdIbEAByZW7yH644IC5zH8/CiFjTCwUx/F
aFIHQlLLzt1kjhD8AbRHhRcsGbzG2ejHsC3yrQddEJSOkInDO8baR0aDyhBTUFPE
lztuekFfaJ1Xcyoc/Zf4pi3ab1Djt+Htck3CHLO/xcl0YYMlM5vcs1QlhQ==
=sAk7
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers updates from Hans de Goede:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software
properties
- bunch of small cleanups, fixes, hw-id additions, etc.
* tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
MAINTAINERS: adjust file entry in INTEL MID PLATFORM
platform/x86: x86-android-tablets: Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
platform/mellanox: mlxbf-pmc: fix lockdep warning
platform/x86/amd: pmf: Add quirk for TUF Gaming A14
platform/x86: touchscreen_dmi: add nanote-next quirk
platform/x86: asus-wmi: don't fail if platform_profile already registered
platform/x86: asus-wmi: add debug print in more key places
platform/x86: intel_scu_wdt: Move intel_scu_wdt.h to x86 subfolder
platform/x86: intel_scu_ipc: Move intel_scu_ipc.h out of arch/x86/include/asm
MAINTAINERS: Add Intel MID section
platform/x86: panasonic-laptop: Add support for programmable buttons
platform/olpc: Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/x86: intel/pmc: Ignore all LTRs during suspend
platform/x86: wmi: Call both legacy and WMI driver notify handlers
platform/x86: wmi: Merge get_event_data() with wmi_get_notify_data()
platform/x86: wmi: Remove wmi_get_event_data()
platform/x86: wmi: Pass event data directly to legacy notify handlers
platform/x86: thinkpad_acpi: Fix uninitialized symbol 's' warning
platform/x86: x86-android-tablets: Fix spelling in the comments
platform/x86: ideapad-laptop: Make the scope_guard() clear of its scope
...
`amd_pstate_prefcore_ranking` reflects the dynamic rankings of a CPU
core based on platform conditions. Explicitly include it in the
documentation.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Explain that the sysfs file represents both preferred core being
enabled by the user and supported by the hardware.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
The special case in amd_pstate_highest_perf_set() is the value used
for calculating the boost numerator. Merge this into
amd_get_boost_ratio_numerator() and then use that to calculate boost
ratio.
This allows dropping more special casing of the highest perf value.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Added documentation about the functionality of efficiency vs. latency tradeoff
control in intel Xeon processors, and how this is configured via sysfs.
Signed-off-by: Tero Kristo <tero.kristo@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240828153657.1296410-2-tero.kristo@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a description of the scaling_available_frequencies attribute in
sysfs to the documentation.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20240701171040.369030-1-rgallaispou@gmail.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Updates the documentation in `amd-pstate.rst` to include information about
the per CPU boost control feature. Users can now enable or disable the
Core Performance Boost (CPB) feature on individual CPUs using the `boost`
sysfs attribute.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240626042733.3747-5-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
the guided mode is also supported, so the operation mode should include
that mode as well.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/a61d825ef71f6aacc8f1624fe9fb982b8446b5a7.1718811234.git.perry.yuan@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Title under line too short
Signed-off-by: Meng Li <li.meng@amd.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce amd-pstate preferred core.
check preferred core state set by the kernel parameter:
$ cat /sys/devices/system/cpu/amd-pstate/prefcore
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Meng Li <li.meng@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix two typos in the admin-guide:
- a missing e in "reference_perf" in cppc_sysfs.rst.
- the amd_pstate sysfs path uses a dash instead of an underscore.
Signed-off-by: Erwan Velu <e.velu@criteo.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit bf5835bcdb ("intel_idle: Disable IBRS during long idle")
disables IBRS when the cstate is 6 or lower. However, there are
some use cases where a customer may want to use max_cstate=1 to
lower latency. Such use cases will suffer from the performance
degradation caused by the enabling of IBRS in the sibling idle thread.
Add a "ibrs_off" module parameter to force disable IBRS and the
CPUIDLE_FLAG_IRQ_ENABLE flag if set.
In the case of a Skylake server with max_cstate=1, this new ibrs_off
option will likely increase the IRQ response latency as IRQ will now
be disabled.
When running SPECjbb2015 with cstates set to C1 on a Skylake system.
First test when the kernel is booted with: "intel_idle.ibrs_off":
max-jOPS = 117828, critical-jOPS = 66047
Then retest when the kernel is booted without the "intel_idle.ibrs_off"
added:
max-jOPS = 116408, critical-jOPS = 58958
That means booting with "intel_idle.ibrs_off" improves performance by:
max-jOPS: +1.2%, which could be considered noise range.
critical-jOPS: +12%, which is definitely a solid improvement.
The admin-guide/pm/intel_idle.rst file is updated to add a description
about the new "ibrs_off" module parameter.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20230727184600.26768-5-longman@redhat.com
An SoC can contain multiple power domains with individual or collection
of mesh partitions. This partition is called fabric cluster.
Certain type of meshes will need to run at the same frequency, they will
be placed in the same fabric cluster. Benefit of fabric cluster is that
it offers a scalable mechanism to deal with partitioned fabrics in a SoC.
The current sysfs interface supports control at package and die level.
This interface is not enough to support more granular control at
fabric cluster level.
SoCs with the support of TPMI (Topology Aware Register and PM Capsule
Interface), can have multiple power domains. Each power domain can
contain one or more fabric clusters.
To support such granular controls, enhance uncore common to optionally
create new directories to provide controls at fabric cluster level. It
is also important to have flexibility to change granularity for future
version of SoCs. If the directory name contains scope like:
"package_*_die_*_power_domain_*_cluster_*", then this is not expandable.
The cpufreq policies also have different scopes. There the scope of the
policy (affected_cpus) specified by attributes inside each policy.
So, follow the same model for uncore frequency scaling sysfs as:
"sys/devices/system/cpu/cpufreq/policy*"
Allow client drivers to optionally support granular control for each
fabric cluster. Here, the directory name will be "uncore" suffixed with
an unique instance number. For example: uncore00, uncore01 etc.
Attributes in the directory identify package id, power domain and
fabric cluster id. This interface is expandable even if some new level
of granularity is introduced. A new sysfs attribute can identify new
level.
For compatibility with the existing sysfs and provide easy way to set
limits for each fabric cluster in the package/die, the existing control
at package/die levels are still provided. For majority of users, this is
an easy approach.
For example: On a single package/die system, with three power domains
and one fabric cluster per power domain:
$tree -L 2 /sys/devices/system/cpu/intel_uncore_frequency/
/sys/devices/system/cpu/intel_uncore_frequency/
├── package_00_die_00
│ ├── current_freq_khz
│ ├── initial_max_freq_khz
│ ├── initial_min_freq_khz
│ ├── max_freq_khz
│ └── min_freq_khz
├── uncore00
│ ├── current_freq_khz
│ ├── domain_id
│ ├── fabric_cluster_id
│ ├── initial_max_freq_khz
│ ├── initial_min_freq_khz
│ ├── max_freq_khz
│ ├── min_freq_khz
│ └── package_id
├── uncore01
│ ├── current_freq_khz
│ ├── domain_id
│ ├── fabric_cluster_id
│ ├── initial_max_freq_khz
│ ├── initial_min_freq_khz
│ ├── max_freq_khz
│ ├── min_freq_khz
│ └── package_id
└── uncore02
├── current_freq_khz
├── domain_id
├── fabric_cluster_id
├── initial_max_freq_khz
├── initial_min_freq_khz
├── max_freq_khz
├── min_freq_khz
└── package_id
The attribute for cluster id is "fabric_cluster_id" instead of just
"cluster_id" is to avoid confusion with usage of term clusters in
other part of the Linux kernel.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>
Link: https://lore.kernel.org/r/20230418171340.681662-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
changes include:
- Some significant additions to the memory-management documentation
- Some improvements to navigation in the HTML-rendered docs
- More Spanish and Chinese translations
...and the usual set of typo fixes and such.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmPzkQUPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YC0QH/09u10xV3N+RuveNE/tArVxKcQi7JZd/xugQ
toSXygh64WY10lzwi7Ms1bHZzpPYB0fOrqTGNqNQuhrVTjQzaZB0BBJqm8lwt2w/
S/Z5wj+IicJTmQ7+0C2Hc/dcK5SCPfY3CgwqOUVdr3dEm1oU+4QaBy31fuIJJ0Hx
NdbXBco8BZqJX9P67jwp9vbrFrSGBjPI0U4HNHVjrWlcBy8JT0aAnf0fyWFy3orA
T86EzmEw8drA1mXsHa5pmVwuHDx2X+D+eRurG9llCBrlIG9EDSmnalY4BeGqR4LS
oDrEH6M91I5+9iWoJ0rBheD8rPclXO2HpjXLApXzTjrORgEYZsM=
=MCdX
-----END PGP SIGNATURE-----
Merge tag 'docs-6.3' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It has been a moderately calm cycle for documentation; the significant
changes include:
- Some significant additions to the memory-management documentation
- Some improvements to navigation in the HTML-rendered docs
- More Spanish and Chinese translations
... and the usual set of typo fixes and such"
* tag 'docs-6.3' of git://git.lwn.net/linux: (68 commits)
Documentation/watchdog/hpwdt: Fix Format
Documentation/watchdog/hpwdt: Fix Reference
Documentation: core-api: padata: correct spelling
docs/mm: Physical Memory: correct spelling in reference to CONFIG_PAGE_EXTENSION
docs: Use HTML comments for the kernel-toc SPDX line
docs: Add more information to the HTML sidebar
Documentation: KVM: Update AMD memory encryption link
printk: Document that CONFIG_BOOT_PRINTK_DELAY required for boot_delay=
Documentation: userspace-api: correct spelling
Documentation: sparc: correct spelling
Documentation: driver-api: correct spelling
Documentation: admin-guide: correct spelling
docs: add workload-tracing document to admin-guide
docs/admin-guide/mm: remove useless markup
docs/mm: remove useless markup
docs/mm: Physical Memory: remove useless markup
docs/sp_SP: Add process magic-number translation
docs: ftrace: always use canonical ftrace path
Doc/damon: fix the data path error
dma-buf: Add "dma-buf" to title of documentation
...
kernel test robot reported htmldocs warning:
Documentation/admin-guide/pm/amd-pstate.rst:343: WARNING: duplicate label admin-guide/pm/amd-pstate:user space interface in ``sysfs``, other instance in Documentation/admin-guide/pm/amd-pstate.rst
The documentation contains two sections with the same "User Space Interface
in ``sysfs``" title. The first one deals with per-policy sysfs and the
second one is about general attributes (currently only global attributes
are documented).
Disambiguate title text of both sections to fix the warning.
Link: https://lore.kernel.org/linux-doc/202302151041.0SWs1RHK-lkp@intel.com/
Fixes: b9e6a2d47b ("Documentation: amd-pstate: introduce new global sysfs attributes")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The amd-pstate driver supports switching working modes at runtime.
Users can view and change modes by interacting with the "status" sysfs
attribute.
1) check driver mode:
$ cat /sys/devices/system/cpu/amd-pstate/status
2) switch mode:
`# echo "passive" | sudo tee /sys/devices/system/cpu/amd-pstate/status`
or
`# echo "active" | sudo tee /sys/devices/system/cpu/amd-pstate/status`
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The amd-pstate driver has two operation modes supported:
* CPPC Autonomous (active) mode
* CPPC non-autonomous (passive) mode.
active mode and passive mode can be chosen by different kernel parameters.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The amd-pstate driver supports a feature called energy performance
preference (EPP). Add information to the documentation to explain
how users can interact with the sysfs files for this feature.
1) See all EPP profiles
$ sudo cat /sys/devices/system/cpu/cpu0/cpufreq/energy_performance_available_preferences
default performance balance_performance balance_power power
2) Check current EPP profile
$ sudo cat /sys/devices/system/cpu/cpu0/cpufreq/energy_performance_preference
performance
3) Set new EPP profile
$ sudo bash -c "echo power > /sys/devices/system/cpu/cpu0/cpufreq/energy_performance_preference"
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wyes Karny <wyes.karny@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The canonical location for the tracefs filesystem is at /sys/kernel/tracing.
But, from Documentation/trace/ftrace.rst:
Before 4.1, all ftrace tracing control files were within the debugfs
file system, which is typically located at /sys/kernel/debug/tracing.
For backward compatibility, when mounting the debugfs file system,
the tracefs file system will be automatically mounted at:
/sys/kernel/debug/tracing
Many parts of Documentation still reference this older debugfs path, so
let's update them to avoid confusion.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20230125213251.2013791-1-zwisler@google.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This Kselftest update for Linux 6.2-rc1 consists of several fixes
and enhancements to existing tests and a few new tests:
- adds new amd-pstate and fixes and enhances existing ones
- adds new watchdog tests and enhances existing ones to improve coverage
- fixes to ftrace, splice_read, rtc, and efivars tests
- fixes to handle egrep obsolescence in the latest grep release
- miscellaneous spelling and SPDX fixes
-----BEGIN PGP SIGNATURE-----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=4cDX
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-next-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest updates from Shuah Khan:
"Several fixes and enhancements to existing tests and a few new tests:
- add new amd-pstate tests and fix and enhance existing ones
- add new watchdog tests and enhance existing ones to improve
coverage
- fixes to ftrace, splice_read, rtc, and efivars tests
- fixes to handle egrep obsolescence in the latest grep release
- miscellaneous spelling and SPDX fixes"
* tag 'linux-kselftest-next-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (24 commits)
selftests/ftrace: Use long for synthetic event probe test
selftests/tpm2: Split async tests call to separate shell script runner
selftests: splice_read: Fix sysfs read cases
selftests: ftrace: Use "grep -E" instead of "egrep"
selftests: gpio: Use "grep -E" instead of "egrep"
selftests: kselftest_deps: Use "grep -E" instead of "egrep"
selftests/efivarfs: Add checking of the test return value
cpufreq: amd-pstate: fix spdxcheck warnings for amd-pstate-ut.c
selftests: rtc: skip when RTC is not present
selftests/ftrace: event_triggers: wait longer for test_event_enable
selftests/vDSO: Add riscv getcpu & gettimeofday test
Documentation: amd-pstate: Add tbench and gitsource test introduction
selftests: amd-pstate: Trigger gitsource benchmark and test cpus
selftests: amd-pstate: Trigger tbench benchmark and test cpus
selftests: amd-pstate: Split basic.sh into run.sh and basic.sh.
selftests: amd-pstate: Rename amd-pstate-ut.sh to basic.sh.
selftests/ftrace: Convert tracer tests to use 'requires' to specify program dependency
selftests/ftrace: Add check for ping command for trigger tests
selftests/watchdog: Fix spelling mistake "Temeprature" -> "Temperature"
selftests/watchdog: add test for WDIOC_GETTEMP
...
Introduce the `amd_pstate` driver new working mode with
`amd_pstate=passive` added to kernel command line.
If there is no passive mode enabled by user, amd_pstate driver will be
disabled by default for now.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce tbench and gitsource test cases design and implementation.
Monitor cpus changes about performance and power consumption etc.
Signed-off-by: Meng Li <li.meng@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Introduce the AMD P-State unit test module design and implementation.
It also talks about kselftest and how to use.
Signed-off-by: Meng Li <li.meng@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
- Respect idle=nomwait when supplied on the kernel cmdline
- Two small cleanups
-----BEGIN PGP SIGNATURE-----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=jkpj
-----END PGP SIGNATURE-----
Merge tag 'x86_cpu_for_v6.0_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpu updates from Borislav Petkov:
- Remove the vendor check when selecting MWAIT as the default idle
state
- Respect idle=nomwait when supplied on the kernel cmdline
- Two small cleanups
* tag 'x86_cpu_for_v6.0_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Use MSR_IA32_MISC_ENABLE constants
x86: Fix comment for X86_FEATURE_ZEN
x86: Remove vendor checks from prefer_mwait_c1_over_halt
x86: Handle idle=nomwait cmdline properly for x86_idle
When kernel is booted with idle=nomwait do not use MWAIT as the
default idle state.
If the user boots the kernel with idle=nomwait, it is a clear
direction to not use mwait as the default idle state.
However, the current code does not take this into consideration
while selecting the default idle state on x86.
Fix it by checking for the idle=nomwait boot option in
prefer_mwait_c1_over_halt().
Also update the documentation around idle=nomwait appropriately.
[ dhansen: tweak commit message ]
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lkml.kernel.org/r/fdc2dc2d0a1bc21c2f53d989ea2d2ee3ccbc0dbe.1654538381.git-series.wyes.karny@amd.com
Update documentation for using the tool to support performance level
change via OOB (Out of Band) interface.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge additional power management documentation udates for 5.18-rc1:
- Add Intel uncore frequency scaling documentation file to its
MAINTAINERS entry (Srinivas Pandruvada).
- Clean up the AMD P-state driver documentation (Jan Engelhardt).
* pm-docs:
Documentation: amd-pstate: grammar and sentence structure updates
MAINTAINERS: Add additional file to uncore frequency control
