Here is the big set of char, misc, iio, and other smaller driver
subsystems for 6.15-rc1. Lots of stuff in here, including:
- loads of IIO changes and driver updates
- counter driver updates
- w1 driver updates
- faux conversions for some drivers that were abusing the platform bus
interface
- coresight driver updates
- rust miscdevice binding updates based on real-world-use
- other minor driver updates
All of these have been in linux-next with no reported issues for quite a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ+mNdQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylktACfYJix41jCCDbiFjnu7Hz4OIdcrUsAnRyF164M
1n5MhEhsEmvQj7WBwQLE
=AmmW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / IIO driver updates from Greg KH:
"Here is the big set of char, misc, iio, and other smaller driver
subsystems for 6.15-rc1. Lots of stuff in here, including:
- loads of IIO changes and driver updates
- counter driver updates
- w1 driver updates
- faux conversions for some drivers that were abusing the platform
bus interface
- coresight driver updates
- rust miscdevice binding updates based on real-world-use
- other minor driver updates
All of these have been in linux-next with no reported issues for quite
a while"
* tag 'char-misc-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
samples: rust_misc_device: fix markup in top-level docs
Coresight: Fix a NULL vs IS_ERR() bug in probe
misc: lis3lv02d: convert to use faux_device
tlclk: convert to use faux_device
regulator: dummy: convert to use the faux device interface
bus: mhi: host: Fix race between unprepare and queue_buf
coresight: configfs: Constify struct config_item_type
doc: iio: ad7380: describe offload support
iio: ad7380: add support for SPI offload
iio: light: Add check for array bounds in veml6075_read_int_time_ms
iio: adc: ti-ads7924 Drop unnecessary function parameters
staging: iio: ad9834: Use devm_regulator_get_enable()
staging: iio: ad9832: Use devm_regulator_get_enable()
iio: gyro: bmg160_spi: add of_match_table
dt-bindings: iio: adc: Add i.MX94 and i.MX95 support
iio: adc: ad7768-1: remove unnecessary locking
Documentation: ABI: add wideband filter type to sysfs-bus-iio
iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset
iio: adc: ad7768-1: Fix conversion result sign
iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config()
...
Add the sysfs file to set/get the enablement of the lane. For MCMB
configurations, the field "E_LN" in CMB_CR register is the
individual lane enables. MCMB lane N is enabled for trace
generation when M_CMB_CR.E=1 and M_CMB_CR.E_LN[N]=1. For lanes
that are not implemented on a given MCMB configuration, the
corresponding bits of this field read as 0 and ignore writes.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250226064008.2531037-4-quic_jinlmao@quicinc.com
TPDM MCMB subunits supports up to 8 lanes CMB. For MCMB
configurations, the field "XTRIG_LNSEL" in CMB_CR register selects
which lane participates in the output pattern mach cross trigger
mechanism governed by the M_CMB_DXPR and M_CMB_XPMR regisers.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250226064008.2531037-3-quic_jinlmao@quicinc.com
Add the nodes for CMB subunit MSR(mux select register) support.
CMB MSRs(mux select registers) is to separate mux, arbitration,
interleaving,data packing control from stream filtering control.
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1707024641-22460-11-git-send-email-quic_taozha@quicinc.com
CMB_TIER register is CMB subunit timestamp insertion enable register.
Bit 0 is PATT_TSENAB bit. Set this bit to 1 to request a timestamp
following a CMB interface pattern match. Bit 1 is XTRIG_TSENAB bit.
Set this bit to 1 to request a timestamp following a CMB CTI timestamp
request. Bit 2 is TS_ALL bit. Set this bit to 1 to request timestamp
for all packets.
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1707024641-22460-9-git-send-email-quic_taozha@quicinc.com
Timestamps are requested if the monitor’s CMB data set unit input
data matches the value in the Monitor CMB timestamp pattern and mask
registers (M_CMB_TPR and M_CMB_TPMR) when CMB timestamp enabled
via the timestamp insertion enable register bit(CMB_TIER.PATT_TSENAB).
The pattern match trigger output is achieved via setting values into
the CMB trigger pattern and mask registers (CMB_XPR and CMB_XPMR).
After configuring a pattern through these registers, the TPDM subunit
will assert an output trigger every time it receives new input data
that matches the configured pattern value. Values in a given bit
number of the mask register correspond to the same bit number in
the corresponding pattern register.
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1707024641-22460-8-git-send-email-quic_taozha@quicinc.com
TPDM CMB subunits support two forms of CMB data set element creation:
continuous and trace-on-change collection mode. Continuous change
creates CMB data set elements on every CMBCLK edge. Trace-on-change
creates CMB data set elements only when a new data set element differs
in value from the previous element in a CMB data set. Set CMB_CR.MODE
to 0 for continuous CMB collection mode. Set CMB_CR.MODE to 1 for
trace-on-change CMB collection mode.
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1707024641-22460-7-git-send-email-quic_taozha@quicinc.com
Add the nodes for DSB subunit MSR(mux select register) support.
The TPDM MSR (mux select register) interface is an optional
interface and associated bank of registers per TPDM subunit.
The intent of mux select registers is to control muxing structures
driving the TPDM’s’ various subunit interfaces.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-14-git-send-email-quic_taozha@quicinc.com
Add nodes to configure the timestamp request based on input
pattern match. Each TPDM that support DSB subunit has maximum of
n(n<7) TPR registers to configure value for timestamp request
based on input pattern match. Eight 32 bit registers providing
DSB interface timestamp request pattern match comparison. And
each TPDM that support DSB subunit has maximum of m(m<7) TPMR
registers to configure pattern mask for timestamp request. Eight
32 bit registers providing DSB interface timestamp request
pattern match mask generation. Add nodes to enable/disable
pattern timestamp and set pattern timestamp type.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-12-git-send-email-quic_taozha@quicinc.com
Add nodes to configure trigger pattern and trigger pattern mask.
Each DSB subunit TPDM has maximum of n(n<7) XPR registers to
configure trigger pattern match output. Eight 32 bit registers
providing DSB interface trigger output pattern match comparison.
And each DSB subunit TPDM has maximum of m(m<7) XPMR registers to
configure trigger pattern mask match output. Eight 32 bit
registers providing DSB interface trigger output pattern match
mask.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-11-git-send-email-quic_taozha@quicinc.com
Add the nodes to set value for DSB edge control and DSB edge
control mask. Each DSB subunit TPDM has maximum of n(n<16) EDCR
resgisters to configure edge control. DSB edge detection control
00: Rising edge detection
01: Falling edge detection
10: Rising and falling edge detection (toggle detection)
And each DSB subunit TPDM has maximum of m(m<8) ECDMR registers to
configure mask. Eight 32 bit registers providing DSB interface
edge detection mask control.
Add the nodes to configure DSB edge control and DSB edge control
mask. Each DSB subunit TPDM maximum of 256 edge detections can be
configured. The index and value sysfs files need to be paired and
written to order. The index sysfs file is to set the index number
of the edge detection which needs to be configured. And the value
sysfs file is to set the control or mask for the edge detection.
DSB edge detection control should be set as the following values.
00: Rising edge detection
01: Falling edge detection
10: Rising and falling edge detection (toggle detection)
And DSB edge mask should be set as 0 or 1.
Each DSB subunit TPDM has maximum of n(n<16) EDCR resgisters to
configure edge control. And each DSB subunit TPDM has maximum of
m(m<8) ECDMR registers to configure mask.
Add the nodes to read a set of the edge control value and mask
of the DSB in TPDM.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-10-git-send-email-quic_taozha@quicinc.com
Add node to set and show programming mode for TPDM DSB subunit.
Once the DSB programming mode is set, it will be written to the
register DSB_CR.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-9-git-send-email-quic_taozha@quicinc.com
The nodes are needed to set or show the trigger timestamp and
trigger type. This change is to add these nodes to achieve these
function.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-8-git-send-email-quic_taozha@quicinc.com
TPDM device need a node to reset the configurations and status of
it. This change provides a node to reset the configurations and
disable the TPDM if it has been enabled.
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/1695882586-10306-7-git-send-email-quic_taozha@quicinc.com
Integration test for tpdm can help to generate the data for
verification of the topology during TPDM software bring up.
Sample:
echo 1 > /sys/bus/coresight/devices/tmc_etf0/enable_sink
echo 1 > /sys/bus/coresight/devices/tpdm0/enable_source
echo 1 > /sys/bus/coresight/devices/tpdm0/integration_test
echo 2 > /sys/bus/coresight/devices/tpdm0/integration_test
cat /dev/tmc_etf0 > /data/etf-tpdm0.bin
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230117145708.16739-6-quic_jinlmao@quicinc.com
