The CAN controller on PolarFire SoC has an AHB peripheral clock _and_ a
CAN bus clock. The bus clock was omitted when the binding was written,
but is required for operation. Make up for lost time and add to the DT.
Fixes: 38a71fc048 ("riscv: dts: microchip: add mpfs's CAN controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one
we support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel phones,
and is grouped with Samsung Exynos here since it is based on the same
SoC design, sharing most of its IP blocks with that series.
- MediaTek MT8188 is a new chip used for mid-range tablets and Chromebooks,
using two Cortex-A78 cores where the older MT8195 had four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4, Cortex-A720
and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest
Laptop chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V,
Powkiddy RK2023, Powkiddy X55) along with the Sonoff iHost Smart
Home Hub and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them.
-----BEGIN PGP SIGNATURE-----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=zR3G
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
The system controller's flash can be accessed via an MSS-exposed QSPI
controller sitting, which sits between the mailbox's control & data
registers. On Icicle, it has an MT25QL01GBBB8ESF connected to it.
The system controller and MSS both have separate QSPI controllers, both
of which can access the flash, although the system controller takes
priority.
Unfortunately, on engineering sample silicon, such as that on Icicle
kits, the MSS' QSPI controller cannot write to the flash due to a bug.
As a workaround, a QSPI controller can be implemented in the FPGA
fabric and the IO routing modified to connect it to the flash in place
of the "hard" controller in the MSS.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The timebase-frequency on PolarFire SoC is not set by an oscillator on
the board, but rather by an internal divider, so move the property to
mpfs.dtsi.
This looks to be copy-pasta from the SiFive Unleashed as the comments
in both places were almost identical. In the Unleashed's case this looks
to actually be valid, as the clock is provided by a crystal on the PCB.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
---
CC: Conor Dooley <conor.dooley@microchip.com>
CC: Daire McNamara <daire.mcnamara@microchip.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
CC: Paul Walmsley <paul.walmsley@sifive.com>
CC: Palmer Dabbelt <palmer@dabbelt.com>
CC: linux-riscv@lists.infradead.org
CC: devicetree@vger.kernel.org
Convert the PolarFire SoC devicetrees to use the new properties
"riscv,isa-base" & "riscv,isa-extensions".
For compatibility with other projects, "riscv,isa" remains.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The mailbox on PolarFire SoC should really have three reg properties,
not two. Without splitting into three sections, the system controller's
QSPI cannot be accessed as it sits inside the current first range. The
driver & binding have been adapted to account for both two & three
ranges, so fix the dts too.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The macb on PolarFire SoC has reset support which the generic compatible
does not use. Add the newly introduced MPFS specific compatible as the
primary compatible to avail of this support & wire up the reset to the
clock controllers devicetree entry.
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The "fabric clocks" in current PolarFire SoC device trees are not
really fixed clocks. Their frequency is set by the bitstream, so having
them located in -fabric.dtsi is not a problem - they're just as "fixed"
as the IP blocks etc used in the FPGA fabric.
However, their configuration can be read at runtime (and to an extent
they can be controlled, although the intended usage is static
configurations set by the bitstream) through the system controller bus.
In the v2022.09 icicle kit reference design a single CCC (north-west
corner) is enabled, using a 50 MHz off-chip oscillator as its reference.
Updating to the v2022.09 icicle kit reference design is required, as
prior to this release, the CCC was not fixed & could change for any
given run of the synthesis tool.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Fixups, reference design changes and new boards:
- The addition of QSPI support for mpfs had a corresponding change to
the devicetree node.
- The v2022.{09,10} reference designs brought with them several memory
map changes which are not backwards compatible. The old devicetrees
from the v2022.08 and earlier releases still work with current
kernels.
- Two new devicetrees for a first-party development kit and for the
Aries Embedded M100FPSEVP kit.
- Corresponding dt-bindings changes for the above.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCY0Qb5gAKCRB4tDGHoIJi
0kEeAQDBUZ3e/RDJlwPVKlZmgcUMbQ8wyaz3e1irlja0W5O+WgD/eQnHec2LrYPz
fSLBCdXpNmViswJBRfmmXDt4l4K9uQs=
=WlDi
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=6hJA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-palmer-v6.1-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into for-next
Microchip RISC-V devicetrees for v6.1
Fixups, reference design changes and new boards:
- The addition of QSPI support for mpfs had a corresponding change to
the devicetree node.
- The v2022.{09,10} reference designs brought with them several memory
map changes which are not backwards compatible. The old devicetrees
from the v2022.08 and earlier releases still work with current
kernels.
- Two new devicetrees for a first-party development kit and for the
Aries Embedded M100FPSEVP kit.
- Corresponding dt-bindings changes for the above.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'dt-for-palmer-v6.1-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: fix fabric i2c reg size
riscv: dts: microchip: update memory configuration for v2022.10
riscv: dts: microchip: add a devicetree for aries' m100pfsevp
riscv: dts: microchip: add sevkit device tree
riscv: dts: microchip: reduce the fic3 clock rate
riscv: dts: microchip: icicle: re-jig fabric peripheral addresses
riscv: dts: microchip: icicle: update pci address properties
riscv: dts: microchip: move the mpfs' pci node to -fabric.dtsi
riscv: dts: microchip: add pci dma ranges for the icicle kit
dt-bindings: riscv: microchip: document the sev kit
dt-bindings: riscv: microchip: document the aries m100pfsevp
dt-bindings: riscv: microchip: document icicle reference design
riscv: dts: microchip: add qspi compatible fallback
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
In today's edition of moving things around:
The PCIe root port on PolarFire SoC is more part of the FPGA than of
the Core Complex. It is located on the other side of the chip and,
apart from its interrupts, most of its configuration is determined
by the FPGA bitstream rather. This includes:
- address translation in both directions
- the addresses at which the config and data regions appear to the
core complex
- the clocks used by the AXI bus
- the plic interrupt used
Moving the PCIe node to the -fabric.dtsi makes it clearer than a
singular configuration for root port is not correct & allows the
base SoC dtsi to be more easily included.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
PolarFire SoC does not have the same l2 cache controller as the fu540,
featuring an extra interrupt. Appease the devicetree checker overlords
by adding a PolarFire SoC specific compatible to fix the below sort of
warnings:
mpfs-polarberry.dtb: cache-controller@2010000: interrupts: [[1], [3], [4], [2]] is too long
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Fixes: 34fc9cc3ae ("riscv: dts: microchip: correct L2 cache interrupts")
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
An AXI master address translation table property was inadvertently
added to the device tree & this was not caught by dtbs_check at the
time. Remove the property - it should not be in mpfs.dtsi anyway as
it would be more suitable in -fabric.dtsi nor does it actually apply
to the version of the reference design we are using for upstream.
Link: https://www.microsemi.com/document-portal/doc_download/1245812-polarfire-fpga-and-polarfire-soc-fpga-pci-express-user-guide # Section 1.3.3
Fixes: 528a5b1f25 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Recent versions of dt-schema complain about the PCIe controller's child
node name:
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dtb: pcie@2000000000: Unevaluated properties are not allowed ('clock-names', 'clocks', 'legacy-interrupt-controller', 'microchip,axi-m-atr0' were unexpected)
From schema: Documentation/devicetree/bindings/pci/microchip,pcie-host.yaml
Make the dts match the correct property name in the dts.
Fixes: 528a5b1f25 ("riscv: dts: microchip: add new peripherals to icicle kit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The "PolarFire SoC MSS Technical Reference Manual" documents the
following PLIC interrupts:
1 - L2 Cache Controller Signals when a metadata correction event occurs
2 - L2 Cache Controller Signals when an uncorrectable metadata event occurs
3 - L2 Cache Controller Signals when a data correction event occurs
4 - L2 Cache Controller Signals when an uncorrectable data event occurs
This differs from the SiFive FU540 which only has three L2 cache related
interrupts.
The sequence in the device tree is defined by an enum:
enum {
DIR_CORR = 0,
DATA_CORR,
DATA_UNCORR,
DIR_UNCORR,
};
So the correct sequence of the L2 cache interrupts is
interrupts = <1>, <3>, <4>, <2>;
[Conor]
This manifests as an unusable system if the l2-cache driver is enabled,
as the wrong interrupt gets cleared & the handler prints errors to the
console ad infinitum.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
CC: stable@vger.kernel.org # 5.15: e35b07a7df: riscv: dts: microchip: mpfs: Group tuples in interrupt properties
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The "hard" QSPI peripheral on PolarFire SoC is derived from version 2
of the FPGA IP core. The original binding had no fallback etc, so this
device tree is valid as is. There was also no functional driver for the
QSPI IP, so no device with a devicetree from a previous mainline
release will regress.
Link: https://lore.kernel.org/linux-spi/7c9f0d96-2882-964a-cd1f-916ddb3f0410@linaro.org/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
* Enabling the FPU is now a static_key.
* Improvements to the Svpbmt support.
* CPU topology bindings for a handful of systems.
* Support for systems with 64-bit hart IDs.
* Many settings have been enabled in the defconfig, including both
support for the StarFive systems and many of the Docker requirements.
There are also a handful of cleanups and improvements, like usual.
-----BEGIN PGP SIGNATURE-----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=v9hn
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Enabling the FPU is now a static_key
- Improvements to the Svpbmt support
- CPU topology bindings for a handful of systems
- Support for systems with 64-bit hart IDs
- Many settings have been enabled in the defconfig, including both
support for the StarFive systems and many of the Docker requirements
There are also a handful of cleanups and improvements, as usual.
* tag 'riscv-for-linus-5.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (28 commits)
riscv: enable Docker requirements in defconfig
riscv: convert the t-head pbmt errata to use the __nops macro
riscv: introduce nops and __nops macros for NOP sequences
RISC-V: Add fast call path of crash_kexec()
riscv: mmap with PROT_WRITE but no PROT_READ is invalid
riscv/efi_stub: Add 64bit boot-hartid support on RV64
riscv: cpu: Add 64bit hartid support on RV64
riscv: smp: Add 64bit hartid support on RV64
riscv: spinwait: Fix hartid variable type
riscv: cpu_ops_sbi: Add 64bit hartid support on RV64
riscv: dts: sifive: "fix" pmic watchdog node name
riscv: dts: canaan: Add k210 topology information
riscv: dts: sifive: Add fu740 topology information
riscv: dts: sifive: Add fu540 topology information
riscv: dts: starfive: Add JH7100 CPU topology
RISC-V: Add CONFIG_{NON,}PORTABLE
riscv: config: enable SOC_STARFIVE in defconfig
riscv: dts: microchip: Add mpfs' topology information
riscv: Kconfig.socs: Add comments
riscv: Kconfig.erratas: Add comments
...
The mpfs has no cpu-map node, so tools like hwloc cannot correctly
parse the topology. Add the node using the existing node labels.
Reported-by: Brice Goglin <Brice.Goglin@inria.fr>
Link: https://github.com/open-mpi/hwloc/issues/536
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
The initial PolarFire SoC devicetree must have been forked off from
the fu540 one prior to the addition of l2cache controller support being
added there. When the controller node was added to mpfs.dtsi, it was
not hooked up to the CPUs & thus sysfs reports an incorrect cache
configuration. Hook it up.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmK28FETHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXdl9B/4h4emFRjxz0BuorLEPezEHbW3ULFES
CqPOgEOj7YalEqECOYrZLf4tmQQEbWcRrKIRmBp7vVLDfSwVtY7fsjUlh0rrbpDh
zXF3uCQDkm07Sy1upBbIXFCU7OBETSbtPKWF87YOcJVWpQbkwacPiokapAnnNy/J
21Sn4dyGADnYxis5QBTu7r5sCF3rxAOBJ+2SrdOeYQ+gdJYlWxPSGL4X+87fYkOE
3b5qR/8gzkGzDEG5PDnyiYgVCprUioE4WZiY7hKmcjGQBAy2q3NOgtz8m71PMI7v
IdDapf85SeLZbO96CXpJBokUthb2HefFMJv0FWwF3uHV93kWSp8ge+VY
=TWdX
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.20-20220625' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-06-25
this is a pull request of 22 patches for net-next/master.
The first 2 patches target the xilinx driver. Srinivas Neeli's patch
adds Transmitter Delay Compensation (TDC) support, a patch by me fixes
a typo.
The next patch is by me and fixes a typo in the m_can driver.
Another patch by me allows the configuration of fixed bit rates
without need for do_set_bittiming callback.
The following 7 patches are by Vincent Mailhol and refactor the
can-dev module and Kbuild, de-inline the can_dropped_invalid_skb()
function, which has grown over the time, and drop outgoing skbs if the
controller is in listen only mode.
Max Staudt's patch fixes a reference in the networking/can.rst
documentation.
Vincent Mailhol provides 2 patches with cleanups for the etas_es58x
driver.
Conor Dooley adds bindings for the mpfs-can to the PolarFire SoC dtsi.
Another patch by me allows the configuration of fixed data bit rates
without need for do_set_data_bittiming callback.
The last 5 patches are by Frank Jungclaus. They prepare the esd_usb
driver to add support for the the CAN-USB/3 device in a later series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the spi-max-frequency property from the spi0 controller
node as it is supposed to be a per SPI peripheral device property.
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/lkml/20220526014141.2872567-1-robh@kernel.org/
Signed-off-by: Nagasuresh Relli <nagasuresh.relli@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
PolarFire SoC has a pair of CAN controllers, but as they were
undocumented there were omitted from the device tree. Add them.
Link: https://lore.kernel.org/all/20220607065459.2035746-3-conor.dooley@microchip.com
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
PolarFire SoC /does/ have a SiFive pdma, despite what I suggested as a
conflict resolution to Zong. Somehow the entry fell through the cracks
between versions of my dt patches, so re-add it with Zong's updated
compatible & dma-channels property.
Fixes: c5094f3710 ("riscv: dts: microchip: refactor icicle kit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
spi-max-frequency property is supposed to be a per SPI peripheral device
property, not a SPI controller property, so remove it.
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/lkml/20220526014141.2872567-1-robh@kernel.org/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Currently mpfs-fabric.dtsi is included by mpfs.dtsi - which is fine
currently since there is only one board with this SoC upstream.
However if another board was added, it would include the fabric contents
of the Icicle Kit's reference design. To avoid this, rename
mpfs-fabric.dtsi to mpfs-icicle-kit-fabric.dtsi & include it in the dts
rather than mpfs.dtsi.
mpfs-icicle-kit-fabric.dtsi specifically matches the 22.03 reference
design for the icicle kit's FPGA fabric & an older version of the
design may not have the i2c or pwm devices - so add the compatible
string to document this.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-6-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Having the SoC vendor both as the directory and in the filename adds
little. Remove microchip from the filenames so that the files will
resemble the other directories in riscv (and arm64). The new names
follow a soc-board.dts & soc{,-fabric}.dtsi pattern.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-4-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
2022-06-01 15:27:54 -07:00
Renamed from arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi (Browse further)
