x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
|
|
|
|
#include <asm/asm-offsets.h>
|
|
|
|
|
#include <asm/asm.h>
|
|
|
|
|
|
|
|
|
|
#include <linux/linkage.h>
|
|
|
|
|
#include <linux/errno.h>
|
|
|
|
|
|
|
|
|
|
#include "../../virt/vmx/tdx/tdxcall.S"
|
|
|
|
|
|
2023-01-12 20:43:43 +01:00
|
|
|
.section .noinstr.text, "ax"
|
|
|
|
|
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
/*
|
2023-08-15 23:01:58 +12:00
|
|
|
* __tdcall() - Used by TDX guests to request services from the TDX
|
|
|
|
|
* module (does not include VMM services) using TDCALL instruction.
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
*
|
2023-08-15 23:01:58 +12:00
|
|
|
* __tdcall() function ABI:
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
*
|
x86/tdx: Pass TDCALL/SEAMCALL input/output registers via a structure
Currently, the TDX_MODULE_CALL asm macro, which handles both TDCALL and
SEAMCALL, takes one parameter for each input register and an optional
'struct tdx_module_output' (a collection of output registers) as output.
This is different from the TDX_HYPERCALL macro which uses a single
'struct tdx_hypercall_args' to carry all input/output registers.
The newer TDX versions introduce more TDCALLs/SEAMCALLs which use more
input/output registers. Also, the TDH.VP.ENTER (which isn't covered
by the current TDX_MODULE_CALL macro) basically can use all registers
that the TDX_HYPERCALL does. The current TDX_MODULE_CALL macro isn't
extendible to cover those cases.
Similar to the TDX_HYPERCALL macro, simplify the TDX_MODULE_CALL macro
to use a single structure 'struct tdx_module_args' to carry all the
input/output registers. Currently, R10/R11 are only used as output
register but not as input by any TDCALL/SEAMCALL. Change to also use
R10/R11 as input register to make input/output registers symmetric.
Currently, the TDX_MODULE_CALL macro depends on the caller to pass a
non-NULL 'struct tdx_module_output' to get additional output registers.
Similar to the TDX_HYPERCALL macro, change the TDX_MODULE_CALL macro to
take a new 'ret' macro argument to indicate whether to save the output
registers to the 'struct tdx_module_args'. Also introduce a new
__tdcall_ret() for that purpose, similar to the __tdx_hypercall_ret().
Note the tdcall(), which is a wrapper of __tdcall(), is called by three
callers: tdx_parse_tdinfo(), tdx_get_ve_info() and tdx_early_init().
The former two need the additional output but the last one doesn't. For
simplicity, make tdcall() always call __tdcall_ret() to avoid another
"_ret()" wrapper. The last caller tdx_early_init() isn't performance
critical anyway.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/483616c1762d85eb3a3c3035a7de061cfacf2f14.1692096753.git.kai.huang%40intel.com
2023-08-15 23:01:59 +12:00
|
|
|
* @fn (RDI) - TDCALL Leaf ID, moved to RAX
|
|
|
|
|
* @args (RSI) - struct tdx_module_args for input
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
*
|
2023-08-15 23:02:00 +12:00
|
|
|
* Only RCX/RDX/R8-R11 are used as input registers.
|
|
|
|
|
*
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
* Return status of TDCALL via RAX.
|
|
|
|
|
*/
|
2023-08-15 23:01:58 +12:00
|
|
|
SYM_FUNC_START(__tdcall)
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
TDX_MODULE_CALL host=0
|
2023-08-15 23:01:58 +12:00
|
|
|
SYM_FUNC_END(__tdcall)
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
|
x86/tdx: Pass TDCALL/SEAMCALL input/output registers via a structure
Currently, the TDX_MODULE_CALL asm macro, which handles both TDCALL and
SEAMCALL, takes one parameter for each input register and an optional
'struct tdx_module_output' (a collection of output registers) as output.
This is different from the TDX_HYPERCALL macro which uses a single
'struct tdx_hypercall_args' to carry all input/output registers.
The newer TDX versions introduce more TDCALLs/SEAMCALLs which use more
input/output registers. Also, the TDH.VP.ENTER (which isn't covered
by the current TDX_MODULE_CALL macro) basically can use all registers
that the TDX_HYPERCALL does. The current TDX_MODULE_CALL macro isn't
extendible to cover those cases.
Similar to the TDX_HYPERCALL macro, simplify the TDX_MODULE_CALL macro
to use a single structure 'struct tdx_module_args' to carry all the
input/output registers. Currently, R10/R11 are only used as output
register but not as input by any TDCALL/SEAMCALL. Change to also use
R10/R11 as input register to make input/output registers symmetric.
Currently, the TDX_MODULE_CALL macro depends on the caller to pass a
non-NULL 'struct tdx_module_output' to get additional output registers.
Similar to the TDX_HYPERCALL macro, change the TDX_MODULE_CALL macro to
take a new 'ret' macro argument to indicate whether to save the output
registers to the 'struct tdx_module_args'. Also introduce a new
__tdcall_ret() for that purpose, similar to the __tdx_hypercall_ret().
Note the tdcall(), which is a wrapper of __tdcall(), is called by three
callers: tdx_parse_tdinfo(), tdx_get_ve_info() and tdx_early_init().
The former two need the additional output but the last one doesn't. For
simplicity, make tdcall() always call __tdcall_ret() to avoid another
"_ret()" wrapper. The last caller tdx_early_init() isn't performance
critical anyway.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/483616c1762d85eb3a3c3035a7de061cfacf2f14.1692096753.git.kai.huang%40intel.com
2023-08-15 23:01:59 +12:00
|
|
|
/*
|
|
|
|
|
* __tdcall_ret() - Used by TDX guests to request services from the TDX
|
|
|
|
|
* module (does not include VMM services) using TDCALL instruction, with
|
|
|
|
|
* saving output registers to the 'struct tdx_module_args' used as input.
|
|
|
|
|
*
|
|
|
|
|
* __tdcall_ret() function ABI:
|
|
|
|
|
*
|
|
|
|
|
* @fn (RDI) - TDCALL Leaf ID, moved to RAX
|
|
|
|
|
* @args (RSI) - struct tdx_module_args for input and output
|
|
|
|
|
*
|
2023-08-15 23:02:00 +12:00
|
|
|
* Only RCX/RDX/R8-R11 are used as input/output registers.
|
|
|
|
|
*
|
x86/tdx: Pass TDCALL/SEAMCALL input/output registers via a structure
Currently, the TDX_MODULE_CALL asm macro, which handles both TDCALL and
SEAMCALL, takes one parameter for each input register and an optional
'struct tdx_module_output' (a collection of output registers) as output.
This is different from the TDX_HYPERCALL macro which uses a single
'struct tdx_hypercall_args' to carry all input/output registers.
The newer TDX versions introduce more TDCALLs/SEAMCALLs which use more
input/output registers. Also, the TDH.VP.ENTER (which isn't covered
by the current TDX_MODULE_CALL macro) basically can use all registers
that the TDX_HYPERCALL does. The current TDX_MODULE_CALL macro isn't
extendible to cover those cases.
Similar to the TDX_HYPERCALL macro, simplify the TDX_MODULE_CALL macro
to use a single structure 'struct tdx_module_args' to carry all the
input/output registers. Currently, R10/R11 are only used as output
register but not as input by any TDCALL/SEAMCALL. Change to also use
R10/R11 as input register to make input/output registers symmetric.
Currently, the TDX_MODULE_CALL macro depends on the caller to pass a
non-NULL 'struct tdx_module_output' to get additional output registers.
Similar to the TDX_HYPERCALL macro, change the TDX_MODULE_CALL macro to
take a new 'ret' macro argument to indicate whether to save the output
registers to the 'struct tdx_module_args'. Also introduce a new
__tdcall_ret() for that purpose, similar to the __tdx_hypercall_ret().
Note the tdcall(), which is a wrapper of __tdcall(), is called by three
callers: tdx_parse_tdinfo(), tdx_get_ve_info() and tdx_early_init().
The former two need the additional output but the last one doesn't. For
simplicity, make tdcall() always call __tdcall_ret() to avoid another
"_ret()" wrapper. The last caller tdx_early_init() isn't performance
critical anyway.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/483616c1762d85eb3a3c3035a7de061cfacf2f14.1692096753.git.kai.huang%40intel.com
2023-08-15 23:01:59 +12:00
|
|
|
* Return status of TDCALL via RAX.
|
|
|
|
|
*/
|
|
|
|
|
SYM_FUNC_START(__tdcall_ret)
|
|
|
|
|
TDX_MODULE_CALL host=0 ret=1
|
|
|
|
|
SYM_FUNC_END(__tdcall_ret)
|
|
|
|
|
|
x86/tdx: Add __tdx_module_call() and __tdx_hypercall() helper functions
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
2022-04-06 02:29:12 +03:00
|
|
|
/*
|
2023-08-15 23:02:02 +12:00
|
|
|
* __tdcall_saved_ret() - Used by TDX guests to request services from the
|
|
|
|
|
* TDX module (including VMM services) using TDCALL instruction, with
|
|
|
|
|
* saving output registers to the 'struct tdx_module_args' used as input.
|
2023-03-21 03:35:11 +03:00
|
|
|
*
|
2023-08-15 23:02:02 +12:00
|
|
|
* __tdcall_saved_ret() function ABI:
|
2023-03-21 03:35:11 +03:00
|
|
|
*
|
x86/tdx: Make TDX_HYPERCALL asm similar to TDX_MODULE_CALL
Now the 'struct tdx_hypercall_args' and 'struct tdx_module_args' are
almost the same, and the TDX_HYPERCALL and TDX_MODULE_CALL asm macro
share similar code pattern too. The __tdx_hypercall() and __tdcall()
should be unified to use the same assembly code.
As a preparation to unify them, simplify the TDX_HYPERCALL to make it
more like the TDX_MODULE_CALL.
The TDX_HYPERCALL takes the pointer of 'struct tdx_hypercall_args' as
function call argument, and does below extra things comparing to the
TDX_MODULE_CALL:
1) It sets RAX to 0 (TDG.VP.VMCALL leaf) internally;
2) It sets RCX to the (fixed) bitmap of shared registers internally;
3) It calls __tdx_hypercall_failed() internally (and panics) when the
TDCALL instruction itself fails;
4) After TDCALL, it moves R10 to RAX to return the return code of the
VMCALL leaf, regardless the '\ret' asm macro argument;
Firstly, change the TDX_HYPERCALL to take the same function call
arguments as the TDX_MODULE_CALL does: TDCALL leaf ID, and the pointer
to 'struct tdx_module_args'. Then 1) and 2) can be moved to the
caller:
- TDG.VP.VMCALL leaf ID can be passed via the function call argument;
- 'struct tdx_module_args' is 'struct tdx_hypercall_args' + RCX, thus
the bitmap of shared registers can be passed via RCX in the
structure.
Secondly, to move 3) and 4) out of assembly, make the TDX_HYPERCALL
always save output registers to the structure. The caller then can:
- Call __tdx_hypercall_failed() when TDX_HYPERCALL returns error;
- Return R10 in the structure as the return code of the VMCALL leaf;
With above changes, change the asm function from __tdx_hypercall() to
__tdcall_hypercall(), and reimplement __tdx_hypercall() as the C wrapper
of it. This avoids having to add another wrapper of __tdx_hypercall()
(_tdx_hypercall() is already taken).
The __tdcall_hypercall() will be replaced with a __tdcall() variant
using TDX_MODULE_CALL in a later commit as the final goal is to have one
assembly to handle both TDCALL and TDVMCALL.
Currently, the __tdx_hypercall() asm is in '.noinstr.text'. To keep
this unchanged, annotate __tdx_hypercall(), which is a C function now,
as 'noinstr'.
Remove the __tdx_hypercall_ret() as __tdx_hypercall() already does so.
Implement __tdx_hypercall() in tdx-shared.c so it can be shared with the
compressed code.
Opportunistically fix a checkpatch error complaining using space around
parenthesis '(' and ')' while moving the bitmap of shared registers to
<asm/shared/tdx.h>.
[ dhansen: quash new calls of __tdx_hypercall_ret() that showed up ]
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/0cbf25e7aee3256288045023a31f65f0cef90af4.1692096753.git.kai.huang%40intel.com
2023-08-15 23:02:01 +12:00
|
|
|
* @fn (RDI) - TDCALL leaf ID, moved to RAX
|
|
|
|
|
* @args (RSI) - struct tdx_module_args for input/output
|
2023-03-21 03:35:11 +03:00
|
|
|
*
|
2023-08-15 23:02:02 +12:00
|
|
|
* All registers in @args are used as input/output registers.
|
2023-03-21 03:35:11 +03:00
|
|
|
*
|
|
|
|
|
* On successful completion, return the hypercall error code.
|
|
|
|
|
*/
|
2023-08-15 23:02:02 +12:00
|
|
|
SYM_FUNC_START(__tdcall_saved_ret)
|
|
|
|
|
TDX_MODULE_CALL host=0 ret=1 saved=1
|
|
|
|
|
SYM_FUNC_END(__tdcall_saved_ret)
|