public-mirrors/linux
1
0
Fork 0
mirror of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git synced 2025-05-24 10:39:52 +00:00
Code Issues Projects Releases Packages Wiki Activity Actions
linux/drivers/net/ethernet/ti/Makefile

23 lines
740 B
Makefile
Raw Normal View History

davinci*/tlan/cpmac: Move the Texas Instruments (TI) drivers Move the Texas Instruments drivers to drivers/net/ethernet/ti/ and make the necessary Kconfig and Makefile changes. CC: Sriram <srk@ti.com> CC: Vinay Hegde <vinay.hegde@ti.com> CC: Cyril Chemparathy <cyril@ti.com> CC: Samuel Chessman <chessman@tux.org> CC: <torben.mathiasen@compaq.com> CC: Eugene Konev <ejka@imfi.kspu.ru> CC: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-06-14 12:56:50 -07:00
#
# Makefile for the TI network device drivers.
#
net: cpsw: Add a minimal cpsw-common module for shared code Looks like davinci_emac and cpsw can share some code although the device registers have a different layout. At least the code for getting the MAC address using syscon can be shared by passing the register offset. Let's start with that and set up a minimal shared cpsw-shared.c. Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-28 11:33:04 -08:00
obj-$(CONFIG_TI_CPSW) += cpsw-common.o
obj-$(CONFIG_TI_DAVINCI_EMAC) += cpsw-common.o
davinci*/tlan/cpmac: Move the Texas Instruments (TI) drivers Move the Texas Instruments drivers to drivers/net/ethernet/ti/ and make the necessary Kconfig and Makefile changes. CC: Sriram <srk@ti.com> CC: Vinay Hegde <vinay.hegde@ti.com> CC: Cyril Chemparathy <cyril@ti.com> CC: Samuel Chessman <chessman@tux.org> CC: <torben.mathiasen@compaq.com> CC: Eugene Konev <ejka@imfi.kspu.ru> CC: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-06-14 12:56:50 -07:00
obj-$(CONFIG_TLAN) += tlan.o
obj-$(CONFIG_CPMAC) += cpmac.o
obj-$(CONFIG_TI_DAVINCI_EMAC) += davinci_emac.o
obj-$(CONFIG_TI_DAVINCI_MDIO) += davinci_mdio.o
obj-$(CONFIG_TI_DAVINCI_CPDMA) += davinci_cpdma.o
drivers: net: cpsw-phy-sel: Add new driver for phy mode selection for cpsw The cpsw currently lacks code to properly set up the hardware interface mode on AM33xx. Other platforms might be equally affected. Usually, the bootloader will configure the control module register, so probably that's why such support wasn't needed in the past. In suspend mode though, this register is modified, and so it needs reprogramming after resume. This patch adds a new driver in which hardware interface can configure correct register bits when the slave is opened. The AM33xx also has a bit for each slave to configure the RMII reference clock direction. Setting it is now supported by a per-slave DT property. This code path introducted by this patch is currently exclusive for am33xx and same can be extened to various platforms via the DT compatibility property. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Daniel Mack <zonque@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-21 00:50:39 +05:30
obj-$(CONFIG_TI_CPSW_PHY_SEL) += cpsw-phy-sel.o
drivers: net: cpsw: make cpsw_ale.c a module to allow re-use on Keystone NetCP on Keystone has cpsw ale function similar to other TI SoCs and this driver is re-used. To allow both ti cpsw and keystone netcp to re-use the driver, convert the cpsw ale to a module and configure it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically linked to both TI CPSW and NetCP and this causes issues when the above drivers are built as dynamic modules. This patch addresses this issue While at it, fix the Makefile and code to build both netcp_core and netcp_ethss as dynamic modules. This is needed to support arm allmodconfig. This also requires exporting of API calls provided by netcp_core so that both the above can be dynamic modules. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-29 18:15:51 -05:00
obj-$(CONFIG_TI_CPSW_ALE) += cpsw_ale.o
net: ethernet: ti: allow cpts to be built separately TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also present as part of NETCP on TI Keystone 2 SoCs. So, It's required to enable build of CPTS for both this drivers and this can be achieved by allowing CPTS to be built separately. Hence, allow cpts to be built separately and convert it to be a module as both CPSW and NETCP drives can be built as modules. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-12-06 18:00:34 -06:00
obj-$(CONFIG_TI_CPTS) += cpts.o
netdev: driver: ethernet: Add TI CPSW driver This patch adds support for TI's CPSW driver. The three port switch gigabit ethernet subsystem provides ethernet packet communication and can be configured as an ethernet switch. Supports 10/100/1000 Mbps. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Sriramakrishnan A G <srk@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-18 20:17:54 +00:00
obj-$(CONFIG_TI_CPSW) += ti_cpsw.o
net: ethernet: ti: allow cpts to be built separately TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also present as part of NETCP on TI Keystone 2 SoCs. So, It's required to enable build of CPTS for both this drivers and this can be achieved by allowing CPTS to be built separately. Hence, allow cpts to be built separately and convert it to be a module as both CPSW and NETCP drives can be built as modules. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-12-06 18:00:34 -06:00
ti_cpsw-y := cpsw.o
net: netcp: Add Keystone NetCP core ethernet driver The network coprocessor (NetCP) is a hardware accelerator available in Keystone SoCs that processes Ethernet packets. NetCP consists of following hardware components 1 Gigabit Ethernet (GbE) subsystem with a Ethernet switch sub-module to send and receive packets. 2 Packet Accelerator (PA) module to perform packet classification operations such as header matching, and packet modification operations such as checksum generation. 3 Security Accelerator(SA) capable of performing IPSec operations on ingress/egress packets. 4 An optional 10 Gigabit Ethernet Subsystem (XGbE) which includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates per Ethernet port. 5 Packet DMA and Queue Management Subsystem (QMSS) to enqueue and dequeue packets and DMA the packets between memory and NetCP hardware components described above. NetCP core driver make use of the Keystone Navigator driver API to allocate DMA channel for the Ethenet device and to handle packet queue/de-queue, Please refer API's in include/linux/soc/ti/knav_dma.h and drivers/soc/ti/knav_qmss.h for details. NetCP driver consists of NetCP core driver and at a minimum Gigabit Ethernet (GBE) module (1) driver to implement the Network device function. Other modules (2,3) can be optionally added to achieve supported hardware acceleration function. The initial version of the driver include NetCP core driver and GBE driver modules. Please refer Documentation/devicetree/bindings/net/keystone-netcp.txt for design of the driver. Cc: David Miller <davem@davemloft.net> Cc: Rob Herring <robh+dt@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Wingman Kwok <w-kwok2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-15 19:12:50 -05:00
obj-$(CONFIG_TI_KEYSTONE_NETCP) += keystone_netcp.o
drivers: net: cpsw: make cpsw_ale.c a module to allow re-use on Keystone NetCP on Keystone has cpsw ale function similar to other TI SoCs and this driver is re-used. To allow both ti cpsw and keystone netcp to re-use the driver, convert the cpsw ale to a module and configure it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically linked to both TI CPSW and NetCP and this causes issues when the above drivers are built as dynamic modules. This patch addresses this issue While at it, fix the Makefile and code to build both netcp_core and netcp_ethss as dynamic modules. This is needed to support arm allmodconfig. This also requires exporting of API calls provided by netcp_core so that both the above can be dynamic modules. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-29 18:15:51 -05:00
keystone_netcp-y := netcp_core.o
obj-$(CONFIG_TI_KEYSTONE_NETCP_ETHSS) += keystone_netcp_ethss.o
keystone_netcp_ethss-y := netcp_ethss.o netcp_sgmii.o netcp_xgbepcsr.o
Reference in a new issue Copy permalink