linux/drivers/gpu/drm/msm/dp/dp_display.c

1799 lines
43 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (c) 2017-2020, The Linux Foundation. All rights reserved.
*/
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/uaccess.h>
#include <linux/debugfs.h>
#include <linux/component.h>
#include <linux/of_irq.h>
#include <linux/delay.h>
#include <drm/display/drm_dp_aux_bus.h>
#include "msm_drv.h"
#include "msm_kms.h"
#include "dp_hpd.h"
#include "dp_parser.h"
#include "dp_power.h"
#include "dp_catalog.h"
#include "dp_aux.h"
#include "dp_reg.h"
#include "dp_link.h"
#include "dp_panel.h"
#include "dp_ctrl.h"
#include "dp_display.h"
#include "dp_drm.h"
#include "dp_audio.h"
#include "dp_debug.h"
#define HPD_STRING_SIZE 30
enum {
ISR_DISCONNECTED,
ISR_CONNECT_PENDING,
ISR_CONNECTED,
ISR_HPD_REPLUG_COUNT,
ISR_IRQ_HPD_PULSE_COUNT,
ISR_HPD_LO_GLITH_COUNT,
};
/* event thread connection state */
enum {
ST_DISCONNECTED,
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
ST_MAINLINK_READY,
ST_CONNECTED,
ST_DISCONNECT_PENDING,
ST_DISPLAY_OFF,
ST_SUSPENDED,
};
enum {
EV_NO_EVENT,
/* hpd events */
EV_HPD_INIT_SETUP,
EV_HPD_PLUG_INT,
EV_IRQ_HPD_INT,
EV_HPD_UNPLUG_INT,
EV_USER_NOTIFICATION,
};
#define EVENT_TIMEOUT (HZ/10) /* 100ms */
#define DP_EVENT_Q_MAX 8
#define DP_TIMEOUT_NONE 0
#define WAIT_FOR_RESUME_TIMEOUT_JIFFIES (HZ / 2)
struct dp_event {
u32 event_id;
u32 data;
u32 delay;
};
struct dp_display_private {
char *name;
int irq;
unsigned int id;
/* state variables */
bool core_initialized;
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
bool phy_initialized;
bool hpd_irq_on;
bool audio_supported;
struct drm_device *drm_dev;
struct platform_device *pdev;
struct dentry *root;
struct dp_usbpd *usbpd;
struct dp_parser *parser;
struct dp_power *power;
struct dp_catalog *catalog;
struct drm_dp_aux *aux;
struct dp_link *link;
struct dp_panel *panel;
struct dp_ctrl *ctrl;
struct dp_debug *debug;
struct dp_usbpd_cb usbpd_cb;
struct dp_display_mode dp_mode;
struct msm_dp dp_display;
/* wait for audio signaling */
struct completion audio_comp;
/* event related only access by event thread */
struct mutex event_mutex;
wait_queue_head_t event_q;
u32 hpd_state;
u32 event_pndx;
u32 event_gndx;
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
struct task_struct *ev_tsk;
struct dp_event event_list[DP_EVENT_Q_MAX];
spinlock_t event_lock;
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
bool wide_bus_en;
struct dp_audio *audio;
};
struct msm_dp_desc {
phys_addr_t io_start;
unsigned int connector_type;
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
bool wide_bus_en;
};
struct msm_dp_config {
const struct msm_dp_desc *descs;
size_t num_descs;
};
static const struct msm_dp_config sc7180_dp_cfg = {
.descs = (const struct msm_dp_desc[]) {
[MSM_DP_CONTROLLER_0] = { .io_start = 0x0ae90000, .connector_type = DRM_MODE_CONNECTOR_DisplayPort },
},
.num_descs = 1,
};
static const struct msm_dp_config sc7280_dp_cfg = {
.descs = (const struct msm_dp_desc[]) {
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
[MSM_DP_CONTROLLER_0] = { .io_start = 0x0ae90000, .connector_type = DRM_MODE_CONNECTOR_DisplayPort, .wide_bus_en = true },
[MSM_DP_CONTROLLER_1] = { .io_start = 0x0aea0000, .connector_type = DRM_MODE_CONNECTOR_eDP, .wide_bus_en = true },
},
.num_descs = 2,
};
static const struct msm_dp_config sc8180x_dp_cfg = {
.descs = (const struct msm_dp_desc[]) {
[MSM_DP_CONTROLLER_0] = { .io_start = 0x0ae90000, .connector_type = DRM_MODE_CONNECTOR_DisplayPort },
[MSM_DP_CONTROLLER_1] = { .io_start = 0x0ae98000, .connector_type = DRM_MODE_CONNECTOR_DisplayPort },
[MSM_DP_CONTROLLER_2] = { .io_start = 0x0ae9a000, .connector_type = DRM_MODE_CONNECTOR_eDP },
},
.num_descs = 3,
};
static const struct msm_dp_config sm8350_dp_cfg = {
.descs = (const struct msm_dp_desc[]) {
[MSM_DP_CONTROLLER_0] = { .io_start = 0x0ae90000, .connector_type = DRM_MODE_CONNECTOR_DisplayPort },
},
.num_descs = 1,
};
static const struct of_device_id dp_dt_match[] = {
{ .compatible = "qcom,sc7180-dp", .data = &sc7180_dp_cfg },
{ .compatible = "qcom,sc7280-dp", .data = &sc7280_dp_cfg },
{ .compatible = "qcom,sc7280-edp", .data = &sc7280_dp_cfg },
{ .compatible = "qcom,sc8180x-dp", .data = &sc8180x_dp_cfg },
{ .compatible = "qcom,sc8180x-edp", .data = &sc8180x_dp_cfg },
{ .compatible = "qcom,sm8350-dp", .data = &sm8350_dp_cfg },
{}
};
static struct dp_display_private *dev_get_dp_display_private(struct device *dev)
{
struct msm_dp *dp = dev_get_drvdata(dev);
return container_of(dp, struct dp_display_private, dp_display);
}
static int dp_add_event(struct dp_display_private *dp_priv, u32 event,
u32 data, u32 delay)
{
unsigned long flag;
struct dp_event *todo;
int pndx;
spin_lock_irqsave(&dp_priv->event_lock, flag);
pndx = dp_priv->event_pndx + 1;
pndx %= DP_EVENT_Q_MAX;
if (pndx == dp_priv->event_gndx) {
pr_err("event_q is full: pndx=%d gndx=%d\n",
dp_priv->event_pndx, dp_priv->event_gndx);
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
return -EPERM;
}
todo = &dp_priv->event_list[dp_priv->event_pndx++];
dp_priv->event_pndx %= DP_EVENT_Q_MAX;
todo->event_id = event;
todo->data = data;
todo->delay = delay;
wake_up(&dp_priv->event_q);
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
return 0;
}
static int dp_del_event(struct dp_display_private *dp_priv, u32 event)
{
unsigned long flag;
struct dp_event *todo;
u32 gndx;
spin_lock_irqsave(&dp_priv->event_lock, flag);
if (dp_priv->event_pndx == dp_priv->event_gndx) {
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
return -ENOENT;
}
gndx = dp_priv->event_gndx;
while (dp_priv->event_pndx != gndx) {
todo = &dp_priv->event_list[gndx];
if (todo->event_id == event) {
todo->event_id = EV_NO_EVENT; /* deleted */
todo->delay = 0;
}
gndx++;
gndx %= DP_EVENT_Q_MAX;
}
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
return 0;
}
void dp_display_signal_audio_start(struct msm_dp *dp_display)
{
struct dp_display_private *dp;
dp = container_of(dp_display, struct dp_display_private, dp_display);
reinit_completion(&dp->audio_comp);
}
void dp_display_signal_audio_complete(struct msm_dp *dp_display)
{
struct dp_display_private *dp;
dp = container_of(dp_display, struct dp_display_private, dp_display);
complete_all(&dp->audio_comp);
}
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
static int dp_hpd_event_thread_start(struct dp_display_private *dp_priv);
static int dp_display_bind(struct device *dev, struct device *master,
void *data)
{
int rc = 0;
struct dp_display_private *dp = dev_get_dp_display_private(dev);
struct msm_drm_private *priv = dev_get_drvdata(master);
struct drm_device *drm = priv->dev;
dp->dp_display.drm_dev = drm;
priv->dp[dp->id] = &dp->dp_display;
rc = dp->parser->parse(dp->parser);
if (rc) {
DRM_ERROR("device tree parsing failed\n");
goto end;
}
dp->drm_dev = drm;
drm/msm/dp: Initialize dp->aux->drm_dev before registration Avoids the following WARN: [ 3.009556] ------------[ cut here ]------------ [ 3.014306] WARNING: CPU: 7 PID: 109 at drivers/gpu/drm/drm_dp_helper.c:1796 drm_dp_aux_register+0xa4/0xac [ 3.024209] Modules linked in: [ 3.027351] CPU: 7 PID: 109 Comm: kworker/7:8 Not tainted 5.10.47 #69 [ 3.033958] Hardware name: Google Lazor (rev1 - 2) (DT) [ 3.039323] Workqueue: events deferred_probe_work_func [ 3.044596] pstate: 60c00009 (nZCv daif +PAN +UAO -TCO BTYPE=--) [ 3.050761] pc : drm_dp_aux_register+0xa4/0xac [ 3.055329] lr : dp_aux_register+0x40/0x88 [ 3.059538] sp : ffffffc010ad3920 [ 3.062948] x29: ffffffc010ad3920 x28: ffffffa64196ac70 [ 3.067239] mmc1: Command Queue Engine enabled [ 3.068406] x27: ffffffa64196ac68 x26: 0000000000000001 [ 3.068407] x25: 0000000000000002 x24: 0000000000000060 [ 3.068409] x23: ffffffa642ab3400 x22: ffffffe126c10e5b [ 3.068410] x21: ffffffa641dc3188 x20: ffffffa641963c10 [ 3.068412] x19: ffffffa642aba910 x18: 00000000ffff0a00 [ 3.068414] x17: 000000476f8e002a x16: 00000000000000b8 [ 3.073008] mmc1: new HS400 Enhanced strobe MMC card at address 0001 [ 3.078448] x15: ffffffffffffffff x14: ffffffffffffffff [ 3.078450] x13: 0000000000000030 x12: 0000000000000030 [ 3.078452] x11: 0101010101010101 x10: ffffffe12647a914 [ 3.078453] x9 : ffffffe12647a8cc x8 : 0000000000000000 [ 3.084452] mmcblk1: mmc1:0001 DA4032 29.1 GiB [ 3.089372] [ 3.089372] x7 : 6c6064717372fefe x6 : ffffffa642b11494 [ 3.089374] x5 : 0000000000000000 x4 : 6d006c657869ffff [ 3.089375] x3 : 000000006c657869 x2 : 000000000000000c [ 3.089376] x1 : ffffffe126c3ae3c x0 : ffffffa642aba910 [ 3.089381] Call trace: [ 3.094931] mmcblk1boot0: mmc1:0001 DA4032 partition 1 4.00 MiB [ 3.100291] drm_dp_aux_register+0xa4/0xac [ 3.100292] dp_aux_register+0x40/0x88 [ 3.100294] dp_display_bind+0x64/0xcc [ 3.100295] component_bind_all+0xdc/0x210 [ 3.100298] msm_drm_bind+0x1e8/0x5d4 [ 3.100301] try_to_bring_up_master+0x168/0x1b0 [ 3.105861] mmcblk1boot1: mmc1:0001 DA4032 partition 2 4.00 MiB [ 3.112282] __component_add+0xa0/0x158 [ 3.112283] component_add+0x1c/0x28 [ 3.112284] dp_display_probe+0x33c/0x380 [ 3.112286] platform_drv_probe+0x9c/0xbc [ 3.112287] really_probe+0x140/0x35c [ 3.112289] driver_probe_device+0x84/0xc0 [ 3.112292] __device_attach_driver+0x94/0xb0 [ 3.117967] mmcblk1rpmb: mmc1:0001 DA4032 partition 3 16.0 MiB, chardev (239:0) [ 3.123201] bus_for_each_drv+0x8c/0xd8 [ 3.123202] __device_attach+0xc4/0x150 [ 3.123204] device_initial_probe+0x1c/0x28 [ 3.123205] bus_probe_device+0x3c/0x9c [ 3.123206] deferred_probe_work_func+0x90/0xcc [ 3.123211] process_one_work+0x218/0x3ec [ 3.131976] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 [ 3.134123] worker_thread+0x288/0x3e8 [ 3.134124] kthread+0x148/0x1b0 [ 3.134127] ret_from_fork+0x10/0x30 [ 3.134128] ---[ end trace cfb9fce3f70f824d ]--- Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> Link: https://lore.kernel.org/r/20210714152910.55093-1-sean@poorly.run Signed-off-by: Rob Clark <robdclark@chromium.org>
2021-07-14 11:28:56 -04:00
dp->aux->drm_dev = drm;
rc = dp_aux_register(dp->aux);
if (rc) {
DRM_ERROR("DRM DP AUX register failed\n");
goto end;
}
rc = dp_power_client_init(dp->power);
if (rc) {
DRM_ERROR("Power client create failed\n");
goto end;
}
rc = dp_register_audio_driver(dev, dp->audio);
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
if (rc) {
DRM_ERROR("Audio registration Dp failed\n");
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
goto end;
}
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
rc = dp_hpd_event_thread_start(dp);
if (rc) {
DRM_ERROR("Event thread create failed\n");
goto end;
}
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
return 0;
end:
return rc;
}
static void dp_display_unbind(struct device *dev, struct device *master,
void *data)
{
struct dp_display_private *dp = dev_get_dp_display_private(dev);
struct msm_drm_private *priv = dev_get_drvdata(master);
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
/* disable all HPD interrupts */
drm/msm/dp: check core_initialized before disable interrupts at dp_display_unbind() During msm initialize phase, dp_display_unbind() will be called to undo initializations had been done by dp_display_bind() previously if there is error happen at msm_drm_bind. In this case, core_initialized flag had to be check to make sure clocks is on before update DP controller register to disable HPD interrupts. Otherwise system will crash due to below NOC fatal error. QTISECLIB [01f01a7ad]CNOC2 ERROR: ERRLOG0_LOW = 0x00061007 QTISECLIB [01f01a7ad]GEM_NOC ERROR: ERRLOG0_LOW = 0x00001007 QTISECLIB [01f0371a0]CNOC2 ERROR: ERRLOG0_HIGH = 0x00000003 QTISECLIB [01f055297]GEM_NOC ERROR: ERRLOG0_HIGH = 0x00000003 QTISECLIB [01f072beb]CNOC2 ERROR: ERRLOG1_LOW = 0x00000024 QTISECLIB [01f0914b8]GEM_NOC ERROR: ERRLOG1_LOW = 0x00000042 QTISECLIB [01f0ae639]CNOC2 ERROR: ERRLOG1_HIGH = 0x00004002 QTISECLIB [01f0cc73f]GEM_NOC ERROR: ERRLOG1_HIGH = 0x00004002 QTISECLIB [01f0ea092]CNOC2 ERROR: ERRLOG2_LOW = 0x0009020c QTISECLIB [01f10895f]GEM_NOC ERROR: ERRLOG2_LOW = 0x0ae9020c QTISECLIB [01f125ae1]CNOC2 ERROR: ERRLOG2_HIGH = 0x00000000 QTISECLIB [01f143be7]GEM_NOC ERROR: ERRLOG2_HIGH = 0x00000000 QTISECLIB [01f16153a]CNOC2 ERROR: ERRLOG3_LOW = 0x00000000 QTISECLIB [01f17fe07]GEM_NOC ERROR: ERRLOG3_LOW = 0x00000000 QTISECLIB [01f19cf89]CNOC2 ERROR: ERRLOG3_HIGH = 0x00000000 QTISECLIB [01f1bb08e]GEM_NOC ERROR: ERRLOG3_HIGH = 0x00000000 QTISECLIB [01f1d8a31]CNOC2 ERROR: SBM1 FAULTINSTATUS0_LOW = 0x00000002 QTISECLIB [01f1f72a4]GEM_NOC ERROR: SBM0 FAULTINSTATUS0_LOW = 0x00000001 QTISECLIB [01f21a217]CNOC3 ERROR: ERRLOG0_LOW = 0x00000006 QTISECLIB [01f23dfd3]NOC error fatal changes in v2: -- drop the first patch (drm/msm: enable msm irq after all initializations are done successfully at msm_drm_init()) since the problem had been fixed by other patch Fixes: 570d3e5d28db ("drm/msm/dp: stop event kernel thread when DP unbind") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/488387/ Link: https://lore.kernel.org/r/1654538139-7450-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
2022-06-06 10:55:39 -07:00
if (dp->core_initialized)
dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_INT_MASK, false);
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
kthread_stop(dp->ev_tsk);
dp_power_client_deinit(dp->power);
dp_aux_unregister(dp->aux);
drm/msm/dp: reset drm_dev to NULL at dp_display_unbind() During msm initialize phase, dp_display_unbind() will be called to undo initializations had been done by dp_display_bind() previously if there is error happen at msm_drm_bind. Under this kind of circumstance, drm_device may not be populated completed which causes system crash at drm_dev_dbg(). This patch reset drm_dev to NULL so that following drm_dev_dbg() will not refer to any internal fields of drm_device to prevent system from crashing. Below are panic stack trace, [ 53.584904] Unable to handle kernel paging request at virtual address 0000000070018001 . [ 53.702212] Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT) [ 53.710445] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 53.717596] pc : string_nocheck+0x1c/0x64 [ 53.721738] lr : string+0x54/0x60 [ 53.725162] sp : ffffffc013d6b650 [ 53.728590] pmr_save: 000000e0 [ 53.731743] x29: ffffffc013d6b650 x28: 0000000000000002 x27: 0000000000ffffff [ 53.739083] x26: ffffffc013d6b710 x25: ffffffd07a066ae0 x24: ffffffd07a419f97 [ 53.746420] x23: ffffffd07a419f99 x22: ffffff81fef360d4 x21: ffffff81fef364d4 [ 53.753760] x20: ffffffc013d6b6f8 x19: ffffffd07a06683c x18: 0000000000000000 [ 53.761093] x17: 4020386678302f30 x16: 00000000000000b0 x15: ffffffd0797523c8 [ 53.768429] x14: 0000000000000004 x13: ffff0000ffffff00 x12: ffffffd07a066b2c [ 53.775780] x11: 0000000000000000 x10: 000000000000013c x9 : 0000000000000000 [ 53.783117] x8 : ffffff81fef364d4 x7 : 0000000000000000 x6 : 0000000000000000 [ 53.790445] x5 : 0000000000000000 x4 : ffff0a00ffffff04 x3 : ffff0a00ffffff04 [ 53.797783] x2 : 0000000070018001 x1 : ffffffffffffffff x0 : ffffff81fef360d4 [ 53.805136] Call trace: [ 53.807667] string_nocheck+0x1c/0x64 [ 53.811439] string+0x54/0x60 [ 53.814498] vsnprintf+0x374/0x53c [ 53.818009] pointer+0x3dc/0x40c [ 53.821340] vsnprintf+0x398/0x53c [ 53.824854] vscnprintf+0x3c/0x88 [ 53.828274] __trace_array_vprintk+0xcc/0x2d4 [ 53.832768] trace_array_printk+0x8c/0xb4 [ 53.836900] drm_trace_printf+0x74/0x9c [ 53.840875] drm_dev_dbg+0xfc/0x1b8 [ 53.844480] dp_pm_suspend+0x70/0xf8 [ 53.848164] dpm_run_callback+0x60/0x1a0 [ 53.852222] __device_suspend+0x304/0x3f4 [ 53.856363] dpm_suspend+0xf8/0x3a8 [ 53.859959] dpm_suspend_start+0x8c/0xc0 Fixes: 570d3e5d28db ("drm/msm/dp: stop event kernel thread when DP unbind") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/490756/ Link: https://lore.kernel.org/r/1655927731-22396-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2022-06-22 12:55:31 -07:00
dp->drm_dev = NULL;
dp->aux->drm_dev = NULL;
priv->dp[dp->id] = NULL;
}
static const struct component_ops dp_display_comp_ops = {
.bind = dp_display_bind,
.unbind = dp_display_unbind,
};
static bool dp_display_is_ds_bridge(struct dp_panel *panel)
{
return (panel->dpcd[DP_DOWNSTREAMPORT_PRESENT] &
DP_DWN_STRM_PORT_PRESENT);
}
static bool dp_display_is_sink_count_zero(struct dp_display_private *dp)
{
drm_dbg_dp(dp->drm_dev, "present=%#x sink_count=%d\n",
dp->panel->dpcd[DP_DOWNSTREAMPORT_PRESENT],
dp->link->sink_count);
return dp_display_is_ds_bridge(dp->panel) &&
(dp->link->sink_count == 0);
}
static void dp_display_send_hpd_event(struct msm_dp *dp_display)
{
struct dp_display_private *dp;
struct drm_connector *connector;
dp = container_of(dp_display, struct dp_display_private, dp_display);
connector = dp->dp_display.connector;
drm_helper_hpd_irq_event(connector->dev);
}
static int dp_display_send_hpd_notification(struct dp_display_private *dp,
bool hpd)
{
if ((hpd && dp->dp_display.is_connected) ||
(!hpd && !dp->dp_display.is_connected)) {
drm_dbg_dp(dp->drm_dev, "HPD already %s\n",
(hpd ? "on" : "off"));
return 0;
}
/* reset video pattern flag on disconnect */
if (!hpd)
dp->panel->video_test = false;
dp->dp_display.is_connected = hpd;
drm_dbg_dp(dp->drm_dev, "type=%d hpd=%d\n",
dp->dp_display.connector_type, hpd);
dp_display_send_hpd_event(&dp->dp_display);
return 0;
}
static int dp_display_process_hpd_high(struct dp_display_private *dp)
{
int rc = 0;
struct edid *edid;
dp->panel->max_dp_lanes = dp->parser->max_dp_lanes;
rc = dp_panel_read_sink_caps(dp->panel, dp->dp_display.connector);
if (rc)
goto end;
dp_link_process_request(dp->link);
edid = dp->panel->edid;
dp->audio_supported = drm_detect_monitor_audio(edid);
dp_panel_handle_sink_request(dp->panel);
dp->dp_display.max_dp_lanes = dp->parser->max_dp_lanes;
/*
* set sink to normal operation mode -- D0
* before dpcd read
*/
dp_link_psm_config(dp->link, &dp->panel->link_info, false);
dp_link_reset_phy_params_vx_px(dp->link);
rc = dp_ctrl_on_link(dp->ctrl);
if (rc) {
DRM_ERROR("failed to complete DP link training\n");
goto end;
}
dp_add_event(dp, EV_USER_NOTIFICATION, true, 0);
end:
return rc;
}
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
static void dp_display_host_phy_init(struct dp_display_private *dp)
{
drm_dbg_dp(dp->drm_dev, "type=%d core_init=%d phy_init=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
if (!dp->phy_initialized) {
dp_ctrl_phy_init(dp->ctrl);
dp->phy_initialized = true;
}
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
}
static void dp_display_host_phy_exit(struct dp_display_private *dp)
{
drm_dbg_dp(dp->drm_dev, "type=%d core_init=%d phy_init=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
if (dp->phy_initialized) {
dp_ctrl_phy_exit(dp->ctrl);
dp->phy_initialized = false;
}
}
static void dp_display_host_init(struct dp_display_private *dp)
{
drm_dbg_dp(dp->drm_dev, "type=%d core_init=%d phy_init=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_power_init(dp->power, false);
dp_ctrl_reset_irq_ctrl(dp->ctrl, true);
dp_aux_init(dp->aux);
dp->core_initialized = true;
}
static void dp_display_host_deinit(struct dp_display_private *dp)
{
drm_dbg_dp(dp->drm_dev, "type=%d core_init=%d phy_init=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_ctrl_reset_irq_ctrl(dp->ctrl, false);
dp_aux_deinit(dp->aux);
dp_power_deinit(dp->power);
dp->core_initialized = false;
}
static int dp_display_usbpd_configure_cb(struct device *dev)
{
struct dp_display_private *dp = dev_get_dp_display_private(dev);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_phy_init(dp);
return dp_display_process_hpd_high(dp);
}
static int dp_display_usbpd_disconnect_cb(struct device *dev)
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
{
return 0;
}
static int dp_display_notify_disconnect(struct device *dev)
{
struct dp_display_private *dp = dev_get_dp_display_private(dev);
dp_add_event(dp, EV_USER_NOTIFICATION, false, 0);
return 0;
}
static void dp_display_handle_video_request(struct dp_display_private *dp)
{
if (dp->link->sink_request & DP_TEST_LINK_VIDEO_PATTERN) {
dp->panel->video_test = true;
dp_link_send_test_response(dp->link);
}
}
static int dp_display_handle_port_ststus_changed(struct dp_display_private *dp)
{
int rc = 0;
if (dp_display_is_sink_count_zero(dp)) {
drm_dbg_dp(dp->drm_dev, "sink count is zero, nothing to do\n");
if (dp->hpd_state != ST_DISCONNECTED) {
dp->hpd_state = ST_DISCONNECT_PENDING;
dp_add_event(dp, EV_USER_NOTIFICATION, false, 0);
}
} else {
if (dp->hpd_state == ST_DISCONNECTED) {
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
dp->hpd_state = ST_MAINLINK_READY;
rc = dp_display_process_hpd_high(dp);
if (rc)
dp->hpd_state = ST_DISCONNECTED;
}
}
return rc;
}
static int dp_display_handle_irq_hpd(struct dp_display_private *dp)
{
u32 sink_request = dp->link->sink_request;
drm_dbg_dp(dp->drm_dev, "%d\n", sink_request);
if (dp->hpd_state == ST_DISCONNECTED) {
if (sink_request & DP_LINK_STATUS_UPDATED) {
drm_dbg_dp(dp->drm_dev, "Disconnected sink_request: %d\n",
sink_request);
DRM_ERROR("Disconnected, no DP_LINK_STATUS_UPDATED\n");
return -EINVAL;
}
}
dp_ctrl_handle_sink_request(dp->ctrl);
if (sink_request & DP_TEST_LINK_VIDEO_PATTERN)
dp_display_handle_video_request(dp);
return 0;
}
static int dp_display_usbpd_attention_cb(struct device *dev)
{
int rc = 0;
u32 sink_request;
struct dp_display_private *dp = dev_get_dp_display_private(dev);
/* check for any test request issued by sink */
rc = dp_link_process_request(dp->link);
if (!rc) {
sink_request = dp->link->sink_request;
drm_dbg_dp(dp->drm_dev, "hpd_state=%d sink_request=%d\n",
dp->hpd_state, sink_request);
if (sink_request & DS_PORT_STATUS_CHANGED)
rc = dp_display_handle_port_ststus_changed(dp);
else
rc = dp_display_handle_irq_hpd(dp);
}
return rc;
}
static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data)
{
struct dp_usbpd *hpd = dp->usbpd;
u32 state;
int ret;
if (!hpd)
return 0;
mutex_lock(&dp->event_mutex);
state = dp->hpd_state;
drm_dbg_dp(dp->drm_dev, "Before, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
if (state == ST_DISPLAY_OFF || state == ST_SUSPENDED) {
mutex_unlock(&dp->event_mutex);
return 0;
}
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
if (state == ST_MAINLINK_READY || state == ST_CONNECTED) {
mutex_unlock(&dp->event_mutex);
return 0;
}
if (state == ST_DISCONNECT_PENDING) {
/* wait until ST_DISCONNECTED */
dp_add_event(dp, EV_HPD_PLUG_INT, 0, 1); /* delay = 1 */
mutex_unlock(&dp->event_mutex);
return 0;
}
ret = dp_display_usbpd_configure_cb(&dp->pdev->dev);
if (ret) { /* link train failed */
dp->hpd_state = ST_DISCONNECTED;
} else {
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
dp->hpd_state = ST_MAINLINK_READY;
}
/* enable HDP irq_hpd/replug interrupt */
dp_catalog_hpd_config_intr(dp->catalog,
DP_DP_IRQ_HPD_INT_MASK | DP_DP_HPD_REPLUG_INT_MASK, true);
drm_dbg_dp(dp->drm_dev, "After, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
mutex_unlock(&dp->event_mutex);
/* uevent will complete connection part */
return 0;
};
static int dp_display_enable(struct dp_display_private *dp, u32 data);
static int dp_display_disable(struct dp_display_private *dp, u32 data);
static void dp_display_handle_plugged_change(struct msm_dp *dp_display,
bool plugged)
{
struct dp_display_private *dp;
dp = container_of(dp_display,
struct dp_display_private, dp_display);
/* notify audio subsystem only if sink supports audio */
if (dp_display->plugged_cb && dp_display->codec_dev &&
dp->audio_supported)
dp_display->plugged_cb(dp_display->codec_dev, plugged);
}
static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
{
struct dp_usbpd *hpd = dp->usbpd;
u32 state;
if (!hpd)
return 0;
mutex_lock(&dp->event_mutex);
state = dp->hpd_state;
drm_dbg_dp(dp->drm_dev, "Before, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
/* disable irq_hpd/replug interrupts */
dp_catalog_hpd_config_intr(dp->catalog,
DP_DP_IRQ_HPD_INT_MASK | DP_DP_HPD_REPLUG_INT_MASK, false);
/* unplugged, no more irq_hpd handle */
dp_del_event(dp, EV_IRQ_HPD_INT);
if (state == ST_DISCONNECTED) {
/* triggered by irq_hdp with sink_count = 0 */
if (dp->link->sink_count == 0) {
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_phy_exit(dp);
}
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
dp_display_notify_disconnect(&dp->pdev->dev);
mutex_unlock(&dp->event_mutex);
return 0;
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
} else if (state == ST_DISCONNECT_PENDING) {
mutex_unlock(&dp->event_mutex);
return 0;
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
} else if (state == ST_MAINLINK_READY) {
dp_ctrl_off_link(dp->ctrl);
dp_display_host_phy_exit(dp);
dp->hpd_state = ST_DISCONNECTED;
dp_display_notify_disconnect(&dp->pdev->dev);
mutex_unlock(&dp->event_mutex);
return 0;
}
/* disable HPD plug interrupts */
dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, false);
/*
* We don't need separate work for disconnect as
* connect/attention interrupts are disabled
*/
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
dp_display_notify_disconnect(&dp->pdev->dev);
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
if (state == ST_DISPLAY_OFF) {
dp->hpd_state = ST_DISCONNECTED;
} else {
dp->hpd_state = ST_DISCONNECT_PENDING;
}
/* signal the disconnect event early to ensure proper teardown */
dp_display_handle_plugged_change(&dp->dp_display, false);
/* enable HDP plug interrupt to prepare for next plugin */
if (!dp->dp_display.is_edp)
dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, true);
drm_dbg_dp(dp->drm_dev, "After, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
/* uevent will complete disconnection part */
mutex_unlock(&dp->event_mutex);
return 0;
}
static int dp_irq_hpd_handle(struct dp_display_private *dp, u32 data)
{
u32 state;
mutex_lock(&dp->event_mutex);
/* irq_hpd can happen at either connected or disconnected state */
state = dp->hpd_state;
drm_dbg_dp(dp->drm_dev, "Before, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
if (state == ST_DISPLAY_OFF || state == ST_SUSPENDED) {
mutex_unlock(&dp->event_mutex);
return 0;
}
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
if (state == ST_MAINLINK_READY || state == ST_DISCONNECT_PENDING) {
/* wait until ST_CONNECTED */
dp_add_event(dp, EV_IRQ_HPD_INT, 0, 1); /* delay = 1 */
mutex_unlock(&dp->event_mutex);
return 0;
}
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_usbpd_attention_cb(&dp->pdev->dev);
drm_dbg_dp(dp->drm_dev, "After, type=%d hpd_state=%d\n",
dp->dp_display.connector_type, state);
mutex_unlock(&dp->event_mutex);
return 0;
}
static void dp_display_deinit_sub_modules(struct dp_display_private *dp)
{
dp_debug_put(dp->debug);
dp_audio_put(dp->audio);
dp_panel_put(dp->panel);
dp_aux_put(dp->aux);
}
static int dp_init_sub_modules(struct dp_display_private *dp)
{
int rc = 0;
struct device *dev = &dp->pdev->dev;
struct dp_usbpd_cb *cb = &dp->usbpd_cb;
struct dp_panel_in panel_in = {
.dev = dev,
};
/* Callback APIs used for cable status change event */
cb->configure = dp_display_usbpd_configure_cb;
cb->disconnect = dp_display_usbpd_disconnect_cb;
cb->attention = dp_display_usbpd_attention_cb;
dp->usbpd = dp_hpd_get(dev, cb);
if (IS_ERR(dp->usbpd)) {
rc = PTR_ERR(dp->usbpd);
DRM_ERROR("failed to initialize hpd, rc = %d\n", rc);
dp->usbpd = NULL;
goto error;
}
dp->parser = dp_parser_get(dp->pdev);
if (IS_ERR(dp->parser)) {
rc = PTR_ERR(dp->parser);
DRM_ERROR("failed to initialize parser, rc = %d\n", rc);
dp->parser = NULL;
goto error;
}
dp->catalog = dp_catalog_get(dev, &dp->parser->io);
if (IS_ERR(dp->catalog)) {
rc = PTR_ERR(dp->catalog);
DRM_ERROR("failed to initialize catalog, rc = %d\n", rc);
dp->catalog = NULL;
goto error;
}
dp->power = dp_power_get(dev, dp->parser);
if (IS_ERR(dp->power)) {
rc = PTR_ERR(dp->power);
DRM_ERROR("failed to initialize power, rc = %d\n", rc);
dp->power = NULL;
goto error;
}
dp->aux = dp_aux_get(dev, dp->catalog, dp->dp_display.is_edp);
if (IS_ERR(dp->aux)) {
rc = PTR_ERR(dp->aux);
DRM_ERROR("failed to initialize aux, rc = %d\n", rc);
dp->aux = NULL;
goto error;
}
dp->link = dp_link_get(dev, dp->aux);
if (IS_ERR(dp->link)) {
rc = PTR_ERR(dp->link);
DRM_ERROR("failed to initialize link, rc = %d\n", rc);
dp->link = NULL;
goto error_link;
}
panel_in.aux = dp->aux;
panel_in.catalog = dp->catalog;
panel_in.link = dp->link;
dp->panel = dp_panel_get(&panel_in);
if (IS_ERR(dp->panel)) {
rc = PTR_ERR(dp->panel);
DRM_ERROR("failed to initialize panel, rc = %d\n", rc);
dp->panel = NULL;
goto error_link;
}
dp->ctrl = dp_ctrl_get(dev, dp->link, dp->panel, dp->aux,
dp->power, dp->catalog, dp->parser);
if (IS_ERR(dp->ctrl)) {
rc = PTR_ERR(dp->ctrl);
DRM_ERROR("failed to initialize ctrl, rc = %d\n", rc);
dp->ctrl = NULL;
goto error_ctrl;
}
dp->audio = dp_audio_get(dp->pdev, dp->panel, dp->catalog);
if (IS_ERR(dp->audio)) {
rc = PTR_ERR(dp->audio);
pr_err("failed to initialize audio, rc = %d\n", rc);
dp->audio = NULL;
goto error_ctrl;
}
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
/* populate wide_bus_en to differernt layers */
dp->ctrl->wide_bus_en = dp->wide_bus_en;
dp->catalog->wide_bus_en = dp->wide_bus_en;
return rc;
error_ctrl:
dp_panel_put(dp->panel);
error_link:
dp_aux_put(dp->aux);
error:
return rc;
}
static int dp_display_set_mode(struct msm_dp *dp_display,
struct dp_display_mode *mode)
{
struct dp_display_private *dp;
dp = container_of(dp_display, struct dp_display_private, dp_display);
dp->panel->dp_mode.drm_mode = mode->drm_mode;
dp->panel->dp_mode.bpp = mode->bpp;
dp->panel->dp_mode.capabilities = mode->capabilities;
dp_panel_init_panel_info(dp->panel);
return 0;
}
static int dp_display_prepare(struct msm_dp *dp_display)
{
return 0;
}
static int dp_display_enable(struct dp_display_private *dp, u32 data)
{
int rc = 0;
struct msm_dp *dp_display = &dp->dp_display;
drm_dbg_dp(dp->drm_dev, "sink_count=%d\n", dp->link->sink_count);
if (dp_display->power_on) {
drm_dbg_dp(dp->drm_dev, "Link already setup, return\n");
return 0;
}
drm/msm/dp: force link training for display resolution change Display resolution change is implemented through drm modeset. Older modeset (resolution) has to be disabled first before newer modeset (resolution) can be enabled. Display disable will turn off both pixel clock and main link clock so that main link have to be re-trained during display enable to have new video stream flow again. At current implementation, display enable function manually kicks up irq_hpd_handle which will read panel link status and start link training if link status is not in sync state. However, there is rare case that a particular panel links status keep staying in sync for some period of time after main link had been shut down previously at display disabled. In this case, main link retraining will not be executed by irq_hdp_handle(). Hence video stream of newer display resolution will fail to be transmitted to panel due to main link is not in sync between host and panel. This patch will bypass irq_hpd_handle() in favor of directly call dp_ctrl_on_stream() to always perform link training in regardless of main link status. So that no unexpected exception resolution change failure cases will happen. Also this implementation are more efficient than manual kicking off irq_hpd_handle function. Changes in v2: -- set force_link_train flag on DP only (is_edp == false) Changes in v3: -- revise commit text -- add Fixes tag Changes in v4: -- revise commit text Changes in v5: -- fix spelling at commit text Changes in v6: -- split dp_ctrl_on_stream() for phy test case -- revise commit text for modeset Changes in v7: -- drop 0 assignment at local variable (ret = 0) Changes in v8: -- add patch to remove pixel_rate from dp_ctrl Changes in v9: -- forward declare dp_ctrl_on_stream_phy_test_report() Fixes: 62671d2ef24b ("drm/msm/dp: fixes wrong connection state caused by failure of link train") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/489895/ Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
2022-06-16 13:26:40 -07:00
rc = dp_ctrl_on_stream(dp->ctrl, data);
if (!rc)
dp_display->power_on = true;
return rc;
}
static int dp_display_post_enable(struct msm_dp *dp_display)
{
struct dp_display_private *dp;
u32 rate;
dp = container_of(dp_display, struct dp_display_private, dp_display);
rate = dp->link->link_params.rate;
if (dp->audio_supported) {
dp->audio->bw_code = drm_dp_link_rate_to_bw_code(rate);
dp->audio->lane_count = dp->link->link_params.num_lanes;
}
/* signal the connect event late to synchronize video and display */
dp_display_handle_plugged_change(dp_display, true);
return 0;
}
static int dp_display_disable(struct dp_display_private *dp, u32 data)
{
struct msm_dp *dp_display = &dp->dp_display;
if (!dp_display->power_on)
return 0;
/* wait only if audio was enabled */
if (dp_display->audio_enabled) {
/* signal the disconnect event */
dp_display_handle_plugged_change(dp_display, false);
if (!wait_for_completion_timeout(&dp->audio_comp,
HZ * 5))
DRM_ERROR("audio comp timeout\n");
}
dp_display->audio_enabled = false;
if (dp->link->sink_count == 0) {
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
/*
* irq_hpd with sink_count = 0
* hdmi unplugged out of dongle
*/
dp_ctrl_off_link_stream(dp->ctrl);
} else {
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
/*
* unplugged interrupt
* dongle unplugged out of DUT
*/
dp_ctrl_off(dp->ctrl);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_phy_exit(dp);
}
dp_display->power_on = false;
drm_dbg_dp(dp->drm_dev, "sink count: %d\n", dp->link->sink_count);
return 0;
}
static int dp_display_unprepare(struct msm_dp *dp_display)
{
return 0;
}
int dp_display_set_plugged_cb(struct msm_dp *dp_display,
hdmi_codec_plugged_cb fn, struct device *codec_dev)
{
bool plugged;
dp_display->plugged_cb = fn;
dp_display->codec_dev = codec_dev;
plugged = dp_display->is_connected;
dp_display_handle_plugged_change(dp_display, plugged);
return 0;
}
/**
* dp_bridge_mode_valid - callback to determine if specified mode is valid
* @bridge: Pointer to drm bridge structure
* @info: display info
* @mode: Pointer to drm mode structure
* Returns: Validity status for specified mode
*/
enum drm_mode_status dp_bridge_mode_valid(struct drm_bridge *bridge,
const struct drm_display_info *info,
const struct drm_display_mode *mode)
{
const u32 num_components = 3, default_bpp = 24;
struct dp_display_private *dp_display;
struct dp_link_info *link_info;
u32 mode_rate_khz = 0, supported_rate_khz = 0, mode_bpp = 0;
struct msm_dp *dp;
int mode_pclk_khz = mode->clock;
dp = to_dp_bridge(bridge)->dp_display;
if (!dp || !mode_pclk_khz || !dp->connector) {
DRM_ERROR("invalid params\n");
return -EINVAL;
}
/*
* The eDP controller currently does not have a reliable way of
* enabling panel power to read sink capabilities. So, we rely
* on the panel driver to populate only supported modes for now.
*/
if (dp->is_edp)
return MODE_OK;
if (mode->clock > DP_MAX_PIXEL_CLK_KHZ)
return MODE_BAD;
dp_display = container_of(dp, struct dp_display_private, dp_display);
link_info = &dp_display->panel->link_info;
mode_bpp = dp->connector->display_info.bpc * num_components;
if (!mode_bpp)
mode_bpp = default_bpp;
mode_bpp = dp_panel_get_mode_bpp(dp_display->panel,
mode_bpp, mode_pclk_khz);
mode_rate_khz = mode_pclk_khz * mode_bpp;
supported_rate_khz = link_info->num_lanes * link_info->rate * 8;
if (mode_rate_khz > supported_rate_khz)
return MODE_BAD;
return MODE_OK;
}
int dp_display_get_modes(struct msm_dp *dp)
{
struct dp_display_private *dp_display;
if (!dp) {
DRM_ERROR("invalid params\n");
return 0;
}
dp_display = container_of(dp, struct dp_display_private, dp_display);
return dp_panel_get_modes(dp_display->panel,
dp->connector);
}
bool dp_display_check_video_test(struct msm_dp *dp)
{
struct dp_display_private *dp_display;
dp_display = container_of(dp, struct dp_display_private, dp_display);
return dp_display->panel->video_test;
}
int dp_display_get_test_bpp(struct msm_dp *dp)
{
struct dp_display_private *dp_display;
if (!dp) {
DRM_ERROR("invalid params\n");
return 0;
}
dp_display = container_of(dp, struct dp_display_private, dp_display);
return dp_link_bit_depth_to_bpp(
dp_display->link->test_video.test_bit_depth);
}
void msm_dp_snapshot(struct msm_disp_state *disp_state, struct msm_dp *dp)
{
struct dp_display_private *dp_display;
dp_display = container_of(dp, struct dp_display_private, dp_display);
/*
* if we are reading registers we need the link clocks to be on
* however till DP cable is connected this will not happen as we
* do not know the resolution to power up with. Hence check the
* power_on status before dumping DP registers to avoid crash due
* to unclocked access
*/
mutex_lock(&dp_display->event_mutex);
if (!dp->power_on) {
mutex_unlock(&dp_display->event_mutex);
return;
}
dp_catalog_snapshot(dp_display->catalog, disp_state);
mutex_unlock(&dp_display->event_mutex);
}
static void dp_display_config_hpd(struct dp_display_private *dp)
{
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_init(dp);
dp_catalog_ctrl_hpd_config(dp->catalog);
/* Enable plug and unplug interrupts only for external DisplayPort */
if (!dp->dp_display.is_edp)
dp_catalog_hpd_config_intr(dp->catalog,
DP_DP_HPD_PLUG_INT_MASK |
DP_DP_HPD_UNPLUG_INT_MASK,
true);
/* Enable interrupt first time
* we are leaving dp clocks on during disconnect
* and never disable interrupt
*/
enable_irq(dp->irq);
}
static int hpd_event_thread(void *data)
{
struct dp_display_private *dp_priv;
unsigned long flag;
struct dp_event *todo;
int timeout_mode = 0;
dp_priv = (struct dp_display_private *)data;
while (1) {
if (timeout_mode) {
wait_event_timeout(dp_priv->event_q,
(dp_priv->event_pndx == dp_priv->event_gndx) ||
kthread_should_stop(), EVENT_TIMEOUT);
} else {
wait_event_interruptible(dp_priv->event_q,
(dp_priv->event_pndx != dp_priv->event_gndx) ||
kthread_should_stop());
}
if (kthread_should_stop())
break;
spin_lock_irqsave(&dp_priv->event_lock, flag);
todo = &dp_priv->event_list[dp_priv->event_gndx];
if (todo->delay) {
struct dp_event *todo_next;
dp_priv->event_gndx++;
dp_priv->event_gndx %= DP_EVENT_Q_MAX;
/* re enter delay event into q */
todo_next = &dp_priv->event_list[dp_priv->event_pndx++];
dp_priv->event_pndx %= DP_EVENT_Q_MAX;
todo_next->event_id = todo->event_id;
todo_next->data = todo->data;
todo_next->delay = todo->delay - 1;
/* clean up older event */
todo->event_id = EV_NO_EVENT;
todo->delay = 0;
/* switch to timeout mode */
timeout_mode = 1;
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
continue;
}
/* timeout with no events in q */
if (dp_priv->event_pndx == dp_priv->event_gndx) {
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
continue;
}
dp_priv->event_gndx++;
dp_priv->event_gndx %= DP_EVENT_Q_MAX;
timeout_mode = 0;
spin_unlock_irqrestore(&dp_priv->event_lock, flag);
switch (todo->event_id) {
case EV_HPD_INIT_SETUP:
dp_display_config_hpd(dp_priv);
break;
case EV_HPD_PLUG_INT:
dp_hpd_plug_handle(dp_priv, todo->data);
break;
case EV_HPD_UNPLUG_INT:
dp_hpd_unplug_handle(dp_priv, todo->data);
break;
case EV_IRQ_HPD_INT:
dp_irq_hpd_handle(dp_priv, todo->data);
break;
case EV_USER_NOTIFICATION:
dp_display_send_hpd_notification(dp_priv,
todo->data);
break;
default:
break;
}
}
return 0;
}
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
static int dp_hpd_event_thread_start(struct dp_display_private *dp_priv)
{
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
/* set event q to empty */
dp_priv->event_gndx = 0;
dp_priv->event_pndx = 0;
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
dp_priv->ev_tsk = kthread_run(hpd_event_thread, dp_priv, "dp_hpd_handler");
if (IS_ERR(dp_priv->ev_tsk))
return PTR_ERR(dp_priv->ev_tsk);
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
return 0;
}
static irqreturn_t dp_display_irq_handler(int irq, void *dev_id)
{
struct dp_display_private *dp = dev_id;
irqreturn_t ret = IRQ_HANDLED;
u32 hpd_isr_status;
if (!dp) {
DRM_ERROR("invalid data\n");
return IRQ_NONE;
}
hpd_isr_status = dp_catalog_hpd_get_intr_status(dp->catalog);
if (hpd_isr_status & 0x0F) {
drm_dbg_dp(dp->drm_dev, "type=%d isr=0x%x\n",
dp->dp_display.connector_type, hpd_isr_status);
/* hpd related interrupts */
if (hpd_isr_status & DP_DP_HPD_PLUG_INT_MASK)
dp_add_event(dp, EV_HPD_PLUG_INT, 0, 0);
if (hpd_isr_status & DP_DP_IRQ_HPD_INT_MASK) {
dp_add_event(dp, EV_IRQ_HPD_INT, 0, 0);
}
if (hpd_isr_status & DP_DP_HPD_REPLUG_INT_MASK) {
dp_add_event(dp, EV_HPD_UNPLUG_INT, 0, 0);
dp_add_event(dp, EV_HPD_PLUG_INT, 0, 3);
}
if (hpd_isr_status & DP_DP_HPD_UNPLUG_INT_MASK)
dp_add_event(dp, EV_HPD_UNPLUG_INT, 0, 0);
}
/* DP controller isr */
dp_ctrl_isr(dp->ctrl);
/* DP aux isr */
dp_aux_isr(dp->aux);
return ret;
}
int dp_display_request_irq(struct msm_dp *dp_display)
{
int rc = 0;
struct dp_display_private *dp;
if (!dp_display) {
DRM_ERROR("invalid input\n");
return -EINVAL;
}
dp = container_of(dp_display, struct dp_display_private, dp_display);
dp->irq = irq_of_parse_and_map(dp->pdev->dev.of_node, 0);
if (!dp->irq) {
DRM_ERROR("failed to get irq\n");
return -EINVAL;
}
rc = devm_request_irq(&dp->pdev->dev, dp->irq,
dp_display_irq_handler,
IRQF_TRIGGER_HIGH, "dp_display_isr", dp);
if (rc < 0) {
DRM_ERROR("failed to request IRQ%u: %d\n",
dp->irq, rc);
return rc;
}
disable_irq(dp->irq);
return 0;
}
static const struct msm_dp_desc *dp_display_get_desc(struct platform_device *pdev,
unsigned int *id)
{
const struct msm_dp_config *cfg = of_device_get_match_data(&pdev->dev);
struct resource *res;
int i;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
return NULL;
for (i = 0; i < cfg->num_descs; i++) {
if (cfg->descs[i].io_start == res->start) {
*id = i;
return &cfg->descs[i];
}
}
dev_err(&pdev->dev, "unknown displayport instance\n");
return NULL;
}
static int dp_display_probe(struct platform_device *pdev)
{
int rc = 0;
struct dp_display_private *dp;
const struct msm_dp_desc *desc;
if (!pdev || !pdev->dev.of_node) {
DRM_ERROR("pdev not found\n");
return -ENODEV;
}
dp = devm_kzalloc(&pdev->dev, sizeof(*dp), GFP_KERNEL);
if (!dp)
return -ENOMEM;
desc = dp_display_get_desc(pdev, &dp->id);
if (!desc)
return -EINVAL;
dp->pdev = pdev;
dp->name = "drm_dp";
dp->dp_display.connector_type = desc->connector_type;
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
dp->wide_bus_en = desc->wide_bus_en;
dp->dp_display.is_edp =
(dp->dp_display.connector_type == DRM_MODE_CONNECTOR_eDP);
rc = dp_init_sub_modules(dp);
if (rc) {
DRM_ERROR("init sub module failed\n");
return -EPROBE_DEFER;
}
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
/* setup event q */
mutex_init(&dp->event_mutex);
drm/msm/dp: stop event kernel thread when DP unbind Current DP driver implementation, event thread is kept running after DP display is unbind. This patch fix this problem by disabling DP irq and stop event thread to exit gracefully at dp_display_unbind(). Changes in v2: -- start event thread at dp_display_bind() Changes in v3: -- disable all HDP interrupts at unbind -- replace dp_hpd_event_setup() with dp_hpd_event_thread_start() -- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop() -- move init_waitqueue_head(&dp->event_q) to probe() -- move spin_lock_init(&dp->event_lock) to probe() Changes in v4: -- relocate both dp_display_bind() and dp_display_unbind() to bottom of file Changes in v5: -- cancel relocation of both dp_display_bind() and dp_display_unbind() Changes in v6: -- move empty event q to dp_event_thread_start() Changes in v7: -- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function Changes in v8: -- return error immediately if audio registration failed. Changes in v9: -- return error immediately if event thread create failed. Changes in v10: -- delete extra DRM_ERROR("failed to create DP event thread\n"); Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/482399/ Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed Fixes tag] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-18 14:56:28 -07:00
init_waitqueue_head(&dp->event_q);
spin_lock_init(&dp->event_lock);
/* Store DP audio handle inside DP display */
dp->dp_display.dp_audio = dp->audio;
init_completion(&dp->audio_comp);
platform_set_drvdata(pdev, &dp->dp_display);
rc = component_add(&pdev->dev, &dp_display_comp_ops);
if (rc) {
DRM_ERROR("component add failed, rc=%d\n", rc);
dp_display_deinit_sub_modules(dp);
}
return rc;
}
static int dp_display_remove(struct platform_device *pdev)
{
struct dp_display_private *dp = dev_get_dp_display_private(&pdev->dev);
dp_display_deinit_sub_modules(dp);
component_del(&pdev->dev, &dp_display_comp_ops);
platform_set_drvdata(pdev, NULL);
return 0;
}
static int dp_pm_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct msm_dp *dp_display = platform_get_drvdata(pdev);
struct dp_display_private *dp;
int sink_count = 0;
dp = container_of(dp_display, struct dp_display_private, dp_display);
mutex_lock(&dp->event_mutex);
drm_dbg_dp(dp->drm_dev,
"Before, type=%d core_inited=%d phy_inited=%d power_on=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized, dp_display->power_on);
/* start from disconnected state */
dp->hpd_state = ST_DISCONNECTED;
/* turn on dp ctrl/phy */
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_init(dp);
dp_catalog_ctrl_hpd_config(dp->catalog);
if (!dp->dp_display.is_edp)
dp_catalog_hpd_config_intr(dp->catalog,
DP_DP_HPD_PLUG_INT_MASK |
DP_DP_HPD_UNPLUG_INT_MASK,
true);
if (dp_catalog_link_is_connected(dp->catalog)) {
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
/*
* set sink to normal operation mode -- D0
* before dpcd read
*/
dp_display_host_phy_init(dp);
dp_link_psm_config(dp->link, &dp->panel->link_info, false);
sink_count = drm_dp_read_sink_count(dp->aux);
if (sink_count < 0)
sink_count = 0;
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_phy_exit(dp);
}
dp->link->sink_count = sink_count;
/*
* can not declared display is connected unless
* HDMI cable is plugged in and sink_count of
* dongle become 1
* also only signal audio when disconnected
*/
if (dp->link->sink_count) {
dp->dp_display.is_connected = true;
} else {
dp->dp_display.is_connected = false;
dp_display_handle_plugged_change(dp_display, false);
}
drm_dbg_dp(dp->drm_dev,
"After, type=%d sink=%d conn=%d core_init=%d phy_init=%d power=%d\n",
dp->dp_display.connector_type, dp->link->sink_count,
dp->dp_display.is_connected, dp->core_initialized,
dp->phy_initialized, dp_display->power_on);
mutex_unlock(&dp->event_mutex);
return 0;
}
static int dp_pm_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct msm_dp *dp_display = platform_get_drvdata(pdev);
struct dp_display_private *dp;
dp = container_of(dp_display, struct dp_display_private, dp_display);
mutex_lock(&dp->event_mutex);
drm_dbg_dp(dp->drm_dev,
"Before, type=%d core_inited=%d phy_inited=%d power_on=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized, dp_display->power_on);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
/* mainlink enabled */
if (dp_power_clk_status(dp->power, DP_CTRL_PM))
dp_ctrl_off_link_stream(dp->ctrl);
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_phy_exit(dp);
/* host_init will be called at pm_resume */
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_deinit(dp);
dp->hpd_state = ST_SUSPENDED;
drm_dbg_dp(dp->drm_dev,
"After, type=%d core_inited=%d phy_inited=%d power_on=%d\n",
dp->dp_display.connector_type, dp->core_initialized,
dp->phy_initialized, dp_display->power_on);
mutex_unlock(&dp->event_mutex);
return 0;
}
static int dp_pm_prepare(struct device *dev)
{
return 0;
}
static void dp_pm_complete(struct device *dev)
{
}
static const struct dev_pm_ops dp_pm_ops = {
.suspend = dp_pm_suspend,
.resume = dp_pm_resume,
.prepare = dp_pm_prepare,
.complete = dp_pm_complete,
};
static struct platform_driver dp_display_driver = {
.probe = dp_display_probe,
.remove = dp_display_remove,
.driver = {
.name = "msm-dp-display",
.of_match_table = dp_dt_match,
.suppress_bind_attrs = true,
.pm = &dp_pm_ops,
},
};
int __init msm_dp_register(void)
{
int ret;
ret = platform_driver_register(&dp_display_driver);
if (ret)
DRM_ERROR("Dp display driver register failed");
return ret;
}
void __exit msm_dp_unregister(void)
{
platform_driver_unregister(&dp_display_driver);
}
void msm_dp_irq_postinstall(struct msm_dp *dp_display)
{
struct dp_display_private *dp;
if (!dp_display)
return;
dp = container_of(dp_display, struct dp_display_private, dp_display);
if (!dp_display->is_edp)
dp_add_event(dp, EV_HPD_INIT_SETUP, 0, 100);
}
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
bool msm_dp_wide_bus_available(const struct msm_dp *dp_display)
{
struct dp_display_private *dp;
dp = container_of(dp_display, struct dp_display_private, dp_display);
drm/msm/dp: enable widebus feature for display port Widebus feature will transmit two pixel data per pixel clock to interface. This feature now is required to be enabled to easy migrant to higher resolution applications in future. However since some legacy chipsets does not support this feature, this feature is enabled by setting wide_bus_en flag to true within msm_dp_desc struct. changes in v2: -- remove compression related code from timing -- remove op_info from struct msm_drm_private -- remove unnecessary wide_bus_en variables -- pass wide_bus_en into timing configuration by struct msm_dp Changes in v3: -- split patch into 3 patches -- enable widebus feature base on chip hardware revision Changes in v5: -- DP_INTF_CONFIG_DATABUS_WIDEN Changes in v6: -- static inline bool msm_dp_wide_bus_enable() in msm_drv.h Changes in v7: -- add Tested-by Changes in v9: -- add wide_bus_en to msm_dp_desc Changes in v10: -- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter Changes in v11: -- add const to dp_catalog_hw_revision() -- add const to msm_dp_wide_bus_available() Changes in v12: -- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog) -- msm_dp_wide_bus_available(const struct msm_dp *dp_display) Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/476283/ Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com [DB: fixed the compilation] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-02-25 13:23:12 -08:00
return dp->wide_bus_en;
}
void msm_dp_debugfs_init(struct msm_dp *dp_display, struct drm_minor *minor)
{
struct dp_display_private *dp;
struct device *dev;
int rc;
dp = container_of(dp_display, struct dp_display_private, dp_display);
dev = &dp->pdev->dev;
dp->debug = dp_debug_get(dev, dp->panel, dp->usbpd,
dp->link, dp->dp_display.connector,
minor);
if (IS_ERR(dp->debug)) {
rc = PTR_ERR(dp->debug);
DRM_ERROR("failed to initialize debug, rc = %d\n", rc);
dp->debug = NULL;
}
}
static int dp_display_get_next_bridge(struct msm_dp *dp)
{
int rc;
struct dp_display_private *dp_priv;
struct device_node *aux_bus;
struct device *dev;
dp_priv = container_of(dp, struct dp_display_private, dp_display);
dev = &dp_priv->pdev->dev;
aux_bus = of_get_child_by_name(dev->of_node, "aux-bus");
if (aux_bus && dp->is_edp) {
dp_display_host_init(dp_priv);
dp_catalog_ctrl_hpd_config(dp_priv->catalog);
dp_display_host_phy_init(dp_priv);
enable_irq(dp_priv->irq);
/*
* The code below assumes that the panel will finish probing
* by the time devm_of_dp_aux_populate_ep_devices() returns.
* This isn't a great assumption since it will fail if the
* panel driver is probed asynchronously but is the best we
* can do without a bigger driver reorganization.
*/
rc = devm_of_dp_aux_populate_ep_devices(dp_priv->aux);
of_node_put(aux_bus);
if (rc)
goto error;
} else if (dp->is_edp) {
DRM_ERROR("eDP aux_bus not found\n");
return -ENODEV;
}
/*
* External bridges are mandatory for eDP interfaces: one has to
* provide at least an eDP panel (which gets wrapped into panel-bridge).
*
* For DisplayPort interfaces external bridges are optional, so
* silently ignore an error if one is not present (-ENODEV).
*/
rc = dp_parser_find_next_bridge(dp_priv->parser);
if (!dp->is_edp && rc == -ENODEV)
return 0;
if (!rc) {
dp->next_bridge = dp_priv->parser->next_bridge;
return 0;
}
error:
if (dp->is_edp) {
disable_irq(dp_priv->irq);
dp_display_host_phy_exit(dp_priv);
dp_display_host_deinit(dp_priv);
}
return rc;
}
int msm_dp_modeset_init(struct msm_dp *dp_display, struct drm_device *dev,
struct drm_encoder *encoder)
{
struct msm_drm_private *priv;
2022-01-18 10:47:26 -08:00
struct dp_display_private *dp_priv;
int ret;
if (WARN_ON(!encoder) || WARN_ON(!dp_display) || WARN_ON(!dev))
return -EINVAL;
priv = dev->dev_private;
dp_display->drm_dev = dev;
2022-01-18 10:47:26 -08:00
dp_priv = container_of(dp_display, struct dp_display_private, dp_display);
ret = dp_display_request_irq(dp_display);
if (ret) {
DRM_ERROR("request_irq failed, ret=%d\n", ret);
return ret;
}
dp_display->encoder = encoder;
ret = dp_display_get_next_bridge(dp_display);
if (ret)
return ret;
2022-01-18 10:47:26 -08:00
dp_display->bridge = dp_bridge_init(dp_display, dev, encoder);
if (IS_ERR(dp_display->bridge)) {
ret = PTR_ERR(dp_display->bridge);
DRM_DEV_ERROR(dev->dev,
"failed to create dp bridge: %d\n", ret);
dp_display->bridge = NULL;
return ret;
}
priv->bridges[priv->num_bridges++] = dp_display->bridge;
dp_display->connector = dp_drm_connector_init(dp_display);
if (IS_ERR(dp_display->connector)) {
ret = PTR_ERR(dp_display->connector);
DRM_DEV_ERROR(dev->dev,
"failed to create dp connector: %d\n", ret);
dp_display->connector = NULL;
return ret;
}
dp_priv->panel->connector = dp_display->connector;
return 0;
}
void dp_bridge_enable(struct drm_bridge *drm_bridge)
{
struct msm_dp_bridge *dp_bridge = to_dp_bridge(drm_bridge);
struct msm_dp *dp = dp_bridge->dp_display;
int rc = 0;
struct dp_display_private *dp_display;
u32 state;
drm/msm/dp: force link training for display resolution change Display resolution change is implemented through drm modeset. Older modeset (resolution) has to be disabled first before newer modeset (resolution) can be enabled. Display disable will turn off both pixel clock and main link clock so that main link have to be re-trained during display enable to have new video stream flow again. At current implementation, display enable function manually kicks up irq_hpd_handle which will read panel link status and start link training if link status is not in sync state. However, there is rare case that a particular panel links status keep staying in sync for some period of time after main link had been shut down previously at display disabled. In this case, main link retraining will not be executed by irq_hdp_handle(). Hence video stream of newer display resolution will fail to be transmitted to panel due to main link is not in sync between host and panel. This patch will bypass irq_hpd_handle() in favor of directly call dp_ctrl_on_stream() to always perform link training in regardless of main link status. So that no unexpected exception resolution change failure cases will happen. Also this implementation are more efficient than manual kicking off irq_hpd_handle function. Changes in v2: -- set force_link_train flag on DP only (is_edp == false) Changes in v3: -- revise commit text -- add Fixes tag Changes in v4: -- revise commit text Changes in v5: -- fix spelling at commit text Changes in v6: -- split dp_ctrl_on_stream() for phy test case -- revise commit text for modeset Changes in v7: -- drop 0 assignment at local variable (ret = 0) Changes in v8: -- add patch to remove pixel_rate from dp_ctrl Changes in v9: -- forward declare dp_ctrl_on_stream_phy_test_report() Fixes: 62671d2ef24b ("drm/msm/dp: fixes wrong connection state caused by failure of link train") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/489895/ Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
2022-06-16 13:26:40 -07:00
bool force_link_train = false;
dp_display = container_of(dp, struct dp_display_private, dp_display);
if (!dp_display->dp_mode.drm_mode.clock) {
DRM_ERROR("invalid params\n");
return;
}
if (dp->is_edp)
dp_hpd_plug_handle(dp_display, 0);
mutex_lock(&dp_display->event_mutex);
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
state = dp_display->hpd_state;
if (state != ST_DISPLAY_OFF && state != ST_MAINLINK_READY) {
mutex_unlock(&dp_display->event_mutex);
return;
}
rc = dp_display_set_mode(dp, &dp_display->dp_mode);
if (rc) {
DRM_ERROR("Failed to perform a mode set, rc=%d\n", rc);
mutex_unlock(&dp_display->event_mutex);
return;
}
rc = dp_display_prepare(dp);
if (rc) {
DRM_ERROR("DP display prepare failed, rc=%d\n", rc);
mutex_unlock(&dp_display->event_mutex);
return;
}
state = dp_display->hpd_state;
drm/msm/dp: force link training for display resolution change Display resolution change is implemented through drm modeset. Older modeset (resolution) has to be disabled first before newer modeset (resolution) can be enabled. Display disable will turn off both pixel clock and main link clock so that main link have to be re-trained during display enable to have new video stream flow again. At current implementation, display enable function manually kicks up irq_hpd_handle which will read panel link status and start link training if link status is not in sync state. However, there is rare case that a particular panel links status keep staying in sync for some period of time after main link had been shut down previously at display disabled. In this case, main link retraining will not be executed by irq_hdp_handle(). Hence video stream of newer display resolution will fail to be transmitted to panel due to main link is not in sync between host and panel. This patch will bypass irq_hpd_handle() in favor of directly call dp_ctrl_on_stream() to always perform link training in regardless of main link status. So that no unexpected exception resolution change failure cases will happen. Also this implementation are more efficient than manual kicking off irq_hpd_handle function. Changes in v2: -- set force_link_train flag on DP only (is_edp == false) Changes in v3: -- revise commit text -- add Fixes tag Changes in v4: -- revise commit text Changes in v5: -- fix spelling at commit text Changes in v6: -- split dp_ctrl_on_stream() for phy test case -- revise commit text for modeset Changes in v7: -- drop 0 assignment at local variable (ret = 0) Changes in v8: -- add patch to remove pixel_rate from dp_ctrl Changes in v9: -- forward declare dp_ctrl_on_stream_phy_test_report() Fixes: 62671d2ef24b ("drm/msm/dp: fixes wrong connection state caused by failure of link train") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/489895/ Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
2022-06-16 13:26:40 -07:00
if (state == ST_DISPLAY_OFF) {
drm/msm/dp: do not initialize phy until plugin interrupt received Current DP drivers have regulators, clocks, irq and phy are grouped together within a function and executed not in a symmetric manner. This increase difficulty of code maintenance and limited code scalability. This patch divides the driver life cycle of operation into four states, resume (including booting up), dongle plugin, dongle unplugged and suspend. Regulators, core clocks and irq are grouped together and enabled at resume (or booting up) so that the DP controller is armed and ready to receive HPD plugin interrupts. HPD plugin interrupt is generated when a dongle plugs into DUT (device under test). Once HPD plugin interrupt is received, DP controller will initialize phy so that dpcd read/write will function and following link training can be proceeded successfully. DP phy will be disabled after main link is teared down at end of unplugged HPD interrupt handle triggered by dongle unplugged out of DUT. Finally regulators, code clocks and irq are disabled at corresponding suspension. Changes in V2: -- removed unnecessary dp_ctrl NULL check -- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs -- remove flip parameter out of dp_ctrl_irq_enable() -- add fixes tag Changes in V3: -- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at dp_display_host_init() for eDP Changes in V4: -- rewording commit text to match this commit changes Changes in V5: -- rebase on top of msm-next branch Changes in V6: -- delete flip variable Changes in V7: -- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl() Changes in V8: -- add more detail comment regrading dp phy at dp_display_host_init() Changes in V9: -- remove set phy_initialized to false when -ECONNRESET detected Changes in v10: -- group into one series Changes in v11: -- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read Changes in v12: -- move dp_display_host_phy_exit() after dp_display_host_deinit() Changes in v13: -- do not execute phy_init until plugged_in interrupt for edp, same as DP. Changes in v14: -- remove redundant dp->core_initialized = false form dp_pm_suspend. Changes in v15: -- remove core_initialized flag check at both host_init and host_deinit Changes in v16: -- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend Changes in v17: -- remove core_initialized checking before execute attention_cb() Changes in v18: -- remove core_initialized checking at dp_pm_suspend Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-01-18 10:47:25 -08:00
dp_display_host_phy_init(dp_display);
drm/msm/dp: force link training for display resolution change Display resolution change is implemented through drm modeset. Older modeset (resolution) has to be disabled first before newer modeset (resolution) can be enabled. Display disable will turn off both pixel clock and main link clock so that main link have to be re-trained during display enable to have new video stream flow again. At current implementation, display enable function manually kicks up irq_hpd_handle which will read panel link status and start link training if link status is not in sync state. However, there is rare case that a particular panel links status keep staying in sync for some period of time after main link had been shut down previously at display disabled. In this case, main link retraining will not be executed by irq_hdp_handle(). Hence video stream of newer display resolution will fail to be transmitted to panel due to main link is not in sync between host and panel. This patch will bypass irq_hpd_handle() in favor of directly call dp_ctrl_on_stream() to always perform link training in regardless of main link status. So that no unexpected exception resolution change failure cases will happen. Also this implementation are more efficient than manual kicking off irq_hpd_handle function. Changes in v2: -- set force_link_train flag on DP only (is_edp == false) Changes in v3: -- revise commit text -- add Fixes tag Changes in v4: -- revise commit text Changes in v5: -- fix spelling at commit text Changes in v6: -- split dp_ctrl_on_stream() for phy test case -- revise commit text for modeset Changes in v7: -- drop 0 assignment at local variable (ret = 0) Changes in v8: -- add patch to remove pixel_rate from dp_ctrl Changes in v9: -- forward declare dp_ctrl_on_stream_phy_test_report() Fixes: 62671d2ef24b ("drm/msm/dp: fixes wrong connection state caused by failure of link train") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/489895/ Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
2022-06-16 13:26:40 -07:00
force_link_train = true;
}
drm/msm/dp: force link training for display resolution change Display resolution change is implemented through drm modeset. Older modeset (resolution) has to be disabled first before newer modeset (resolution) can be enabled. Display disable will turn off both pixel clock and main link clock so that main link have to be re-trained during display enable to have new video stream flow again. At current implementation, display enable function manually kicks up irq_hpd_handle which will read panel link status and start link training if link status is not in sync state. However, there is rare case that a particular panel links status keep staying in sync for some period of time after main link had been shut down previously at display disabled. In this case, main link retraining will not be executed by irq_hdp_handle(). Hence video stream of newer display resolution will fail to be transmitted to panel due to main link is not in sync between host and panel. This patch will bypass irq_hpd_handle() in favor of directly call dp_ctrl_on_stream() to always perform link training in regardless of main link status. So that no unexpected exception resolution change failure cases will happen. Also this implementation are more efficient than manual kicking off irq_hpd_handle function. Changes in v2: -- set force_link_train flag on DP only (is_edp == false) Changes in v3: -- revise commit text -- add Fixes tag Changes in v4: -- revise commit text Changes in v5: -- fix spelling at commit text Changes in v6: -- split dp_ctrl_on_stream() for phy test case -- revise commit text for modeset Changes in v7: -- drop 0 assignment at local variable (ret = 0) Changes in v8: -- add patch to remove pixel_rate from dp_ctrl Changes in v9: -- forward declare dp_ctrl_on_stream_phy_test_report() Fixes: 62671d2ef24b ("drm/msm/dp: fixes wrong connection state caused by failure of link train") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/489895/ Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
2022-06-16 13:26:40 -07:00
dp_display_enable(dp_display, force_link_train);
rc = dp_display_post_enable(dp);
if (rc) {
DRM_ERROR("DP display post enable failed, rc=%d\n", rc);
dp_display_disable(dp_display, 0);
dp_display_unprepare(dp);
}
/* completed connection */
dp_display->hpd_state = ST_CONNECTED;
drm_dbg_dp(dp->drm_dev, "type=%d Done\n", dp->connector_type);
mutex_unlock(&dp_display->event_mutex);
}
void dp_bridge_disable(struct drm_bridge *drm_bridge)
{
struct msm_dp_bridge *dp_bridge = to_dp_bridge(drm_bridge);
struct msm_dp *dp = dp_bridge->dp_display;
struct dp_display_private *dp_display;
dp_display = container_of(dp, struct dp_display_private, dp_display);
dp_ctrl_push_idle(dp_display->ctrl);
}
void dp_bridge_post_disable(struct drm_bridge *drm_bridge)
{
struct msm_dp_bridge *dp_bridge = to_dp_bridge(drm_bridge);
struct msm_dp *dp = dp_bridge->dp_display;
int rc = 0;
u32 state;
struct dp_display_private *dp_display;
dp_display = container_of(dp, struct dp_display_private, dp_display);
if (dp->is_edp)
dp_hpd_unplug_handle(dp_display, 0);
mutex_lock(&dp_display->event_mutex);
drm/msm/dp: tear down main link at unplug handle immediately Two stages are required to setup up main link to be ready to transmit video stream. Stage 1: dp_hpd_plug_handle() perform link training to set up main link stage 2: user space framework (msm_dp_display_enable()) to enable pixel clock and transfer main link to video ready state. At current implementation, when dongle unplugged dp_hdp_unplug_handle() has to wait until stage 2 completed before it can send link down uevent to user space framework to disable pixel clock followed by tearing down main link. This introduce unnecessary latency if dongle unplugged happen after stage 1 and before stage 2. It also has possibility leave main link stay at ready state after dongle unplugged if framework does not response to link down uevent notification. This will prevent next dongle plug in from working. This scenario could possibly happen when dongle unplug while system in the middle of suspending. This patch allow unplug handle to tear down main link and notify framework link down immediately if dongle unplugged happen after stage 1 and before stage 2. With this approach, dp driver is much more resilient to any different scenarios. Also redundant both dp_connect_pending_timeout() and dp_disconnect_pending_timeout() are removed to reduce logic complexity. Changes in V2: -- return -EINVAL at msm_dp_display_enable() if not in correct state -- replace ST_CONNECT_PENDING with ST_MAINLINK_READY Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Patchwork: https://patchwork.freedesktop.org/patch/483391/ Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com [DB: fixed return values due to conversion to function merge] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2022-04-25 15:56:22 -07:00
state = dp_display->hpd_state;
if (state != ST_DISCONNECT_PENDING && state != ST_CONNECTED) {
mutex_unlock(&dp_display->event_mutex);
return;
}
dp_display_disable(dp_display, 0);
rc = dp_display_unprepare(dp);
if (rc)
DRM_ERROR("DP display unprepare failed, rc=%d\n", rc);
state = dp_display->hpd_state;
if (state == ST_DISCONNECT_PENDING) {
/* completed disconnection */
dp_display->hpd_state = ST_DISCONNECTED;
} else {
dp_display->hpd_state = ST_DISPLAY_OFF;
}
drm_dbg_dp(dp->drm_dev, "type=%d Done\n", dp->connector_type);
mutex_unlock(&dp_display->event_mutex);
}
void dp_bridge_mode_set(struct drm_bridge *drm_bridge,
const struct drm_display_mode *mode,
const struct drm_display_mode *adjusted_mode)
{
struct msm_dp_bridge *dp_bridge = to_dp_bridge(drm_bridge);
struct msm_dp *dp = dp_bridge->dp_display;
struct dp_display_private *dp_display;
dp_display = container_of(dp, struct dp_display_private, dp_display);
memset(&dp_display->dp_mode, 0x0, sizeof(struct dp_display_mode));
if (dp_display_check_video_test(dp))
dp_display->dp_mode.bpp = dp_display_get_test_bpp(dp);
else /* Default num_components per pixel = 3 */
dp_display->dp_mode.bpp = dp->connector->display_info.bpc * 3;
if (!dp_display->dp_mode.bpp)
dp_display->dp_mode.bpp = 24; /* Default bpp */
drm_mode_copy(&dp_display->dp_mode.drm_mode, adjusted_mode);
dp_display->dp_mode.v_active_low =
!!(dp_display->dp_mode.drm_mode.flags & DRM_MODE_FLAG_NVSYNC);
dp_display->dp_mode.h_active_low =
!!(dp_display->dp_mode.drm_mode.flags & DRM_MODE_FLAG_NHSYNC);
}