linux/drivers/net/ethernet/ti/icssg/icssg_config.c

858 lines
24 KiB
C
Raw Permalink Normal View History

// SPDX-License-Identifier: GPL-2.0
/* ICSSG Ethernet driver
*
* Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
*/
#include <linux/iopoll.h>
#include <linux/regmap.h>
#include <uapi/linux/if_ether.h>
#include "icssg_config.h"
#include "icssg_prueth.h"
#include "icssg_switch_map.h"
#include "icssg_mii_rt.h"
/* TX IPG Values to be set for 100M link speed. These values are
* in ocp_clk cycles. So need change if ocp_clk is changed for a specific
* h/w design.
*/
/* IPG is in core_clk cycles */
#define MII_RT_TX_IPG_100M 0x17
#define MII_RT_TX_IPG_1G 0xb
#define MII_RT_TX_IPG_100M_SR1 0x166
#define MII_RT_TX_IPG_1G_SR1 0x1a
#define ICSSG_QUEUES_MAX 64
#define ICSSG_QUEUE_OFFSET 0xd00
#define ICSSG_QUEUE_PEEK_OFFSET 0xe00
#define ICSSG_QUEUE_CNT_OFFSET 0xe40
#define ICSSG_QUEUE_RESET_OFFSET 0xf40
#define ICSSG_NUM_TX_QUEUES 8
#define RECYCLE_Q_SLICE0 16
#define RECYCLE_Q_SLICE1 17
#define ICSSG_NUM_OTHER_QUEUES 5 /* port, host and special queues */
#define PORT_HI_Q_SLICE0 32
#define PORT_LO_Q_SLICE0 33
#define HOST_HI_Q_SLICE0 34
#define HOST_LO_Q_SLICE0 35
#define HOST_SPL_Q_SLICE0 40 /* Special Queue */
#define PORT_HI_Q_SLICE1 36
#define PORT_LO_Q_SLICE1 37
#define HOST_HI_Q_SLICE1 38
#define HOST_LO_Q_SLICE1 39
#define HOST_SPL_Q_SLICE1 41 /* Special Queue */
#define MII_RXCFG_DEFAULT (PRUSS_MII_RT_RXCFG_RX_ENABLE | \
PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS | \
PRUSS_MII_RT_RXCFG_RX_L2_EN | \
PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS)
#define MII_TXCFG_DEFAULT (PRUSS_MII_RT_TXCFG_TX_ENABLE | \
PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE | \
PRUSS_MII_RT_TXCFG_TX_32_MODE_EN | \
PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN)
#define ICSSG_CFG_DEFAULT (ICSSG_CFG_TX_L1_EN | \
ICSSG_CFG_TX_L2_EN | ICSSG_CFG_RX_L2_G_EN | \
ICSSG_CFG_TX_PRU_EN | \
ICSSG_CFG_SGMII_MODE)
#define FDB_GEN_CFG1 0x60
#define SMEM_VLAN_OFFSET 8
#define SMEM_VLAN_OFFSET_MASK GENMASK(25, 8)
#define FDB_GEN_CFG2 0x64
#define FDB_VLAN_EN BIT(6)
#define FDB_HOST_EN BIT(2)
#define FDB_PRU1_EN BIT(1)
#define FDB_PRU0_EN BIT(0)
#define FDB_EN_ALL (FDB_PRU0_EN | FDB_PRU1_EN | \
FDB_HOST_EN | FDB_VLAN_EN)
/**
* struct map - ICSSG Queue Map
* @queue: Queue number
* @pd_addr_start: Packet descriptor queue reserved memory
* @flags: Flags
* @special: Indicates whether this queue is a special queue or not
*/
struct map {
int queue;
u32 pd_addr_start;
u32 flags;
bool special;
};
/* Hardware queue map for ICSSG */
static const struct map hwq_map[2][ICSSG_NUM_OTHER_QUEUES] = {
{
{ PORT_HI_Q_SLICE0, PORT_DESC0_HI, 0x200000, 0 },
{ PORT_LO_Q_SLICE0, PORT_DESC0_LO, 0, 0 },
{ HOST_HI_Q_SLICE0, HOST_DESC0_HI, 0x200000, 0 },
{ HOST_LO_Q_SLICE0, HOST_DESC0_LO, 0, 0 },
{ HOST_SPL_Q_SLICE0, HOST_SPPD0, 0x400000, 1 },
},
{
{ PORT_HI_Q_SLICE1, PORT_DESC1_HI, 0xa00000, 0 },
{ PORT_LO_Q_SLICE1, PORT_DESC1_LO, 0x800000, 0 },
{ HOST_HI_Q_SLICE1, HOST_DESC1_HI, 0xa00000, 0 },
{ HOST_LO_Q_SLICE1, HOST_DESC1_LO, 0x800000, 0 },
{ HOST_SPL_Q_SLICE1, HOST_SPPD1, 0xc00000, 1 },
},
};
static void icssg_config_mii_init_fw_offload(struct prueth_emac *emac)
{
struct prueth *prueth = emac->prueth;
int mii = prueth_emac_slice(emac);
u32 txcfg_reg, pcnt_reg, txcfg;
struct regmap *mii_rt;
mii_rt = prueth->mii_rt;
txcfg_reg = (mii == ICSS_MII0) ? PRUSS_MII_RT_TXCFG0 :
PRUSS_MII_RT_TXCFG1;
pcnt_reg = (mii == ICSS_MII0) ? PRUSS_MII_RT_RX_PCNT0 :
PRUSS_MII_RT_RX_PCNT1;
txcfg = PRUSS_MII_RT_TXCFG_TX_ENABLE |
PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE |
PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN;
if (emac->phy_if == PHY_INTERFACE_MODE_MII && mii == ICSS_MII1)
txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
else if (emac->phy_if != PHY_INTERFACE_MODE_MII && mii == ICSS_MII0)
txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
regmap_write(mii_rt, txcfg_reg, txcfg);
regmap_write(mii_rt, pcnt_reg, 0x1);
}
static void icssg_config_mii_init(struct prueth_emac *emac)
{
struct prueth *prueth = emac->prueth;
int slice = prueth_emac_slice(emac);
u32 txcfg, txcfg_reg, pcnt_reg;
struct regmap *mii_rt;
mii_rt = prueth->mii_rt;
txcfg_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_TXCFG0 :
PRUSS_MII_RT_TXCFG1;
pcnt_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_RX_PCNT0 :
PRUSS_MII_RT_RX_PCNT1;
txcfg = MII_TXCFG_DEFAULT;
/* In MII mode TX lines swapped inside ICSSG, so TX_MUX_SEL cfg need
* to be swapped also comparing to RGMII mode.
*/
if (emac->phy_if == PHY_INTERFACE_MODE_MII && slice == ICSS_MII0)
txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
else if (emac->phy_if != PHY_INTERFACE_MODE_MII && slice == ICSS_MII1)
txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
regmap_write(mii_rt, txcfg_reg, txcfg);
regmap_write(mii_rt, pcnt_reg, 0x1);
}
static void icssg_miig_queues_init(struct prueth *prueth, int slice)
{
struct regmap *miig_rt = prueth->miig_rt;
void __iomem *smem = prueth->shram.va;
u8 pd[ICSSG_SPECIAL_PD_SIZE];
int queue = 0, i, j;
u32 *pdword;
/* reset hwqueues */
if (slice)
queue = ICSSG_NUM_TX_QUEUES;
for (i = 0; i < ICSSG_NUM_TX_QUEUES; i++) {
regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET, queue);
queue++;
}
queue = slice ? RECYCLE_Q_SLICE1 : RECYCLE_Q_SLICE0;
regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET, queue);
for (i = 0; i < ICSSG_NUM_OTHER_QUEUES; i++) {
regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET,
hwq_map[slice][i].queue);
}
/* initialize packet descriptors in SMEM */
/* push pakcet descriptors to hwqueues */
pdword = (u32 *)pd;
for (j = 0; j < ICSSG_NUM_OTHER_QUEUES; j++) {
const struct map *mp;
int pd_size, num_pds;
u32 pdaddr;
mp = &hwq_map[slice][j];
if (mp->special) {
pd_size = ICSSG_SPECIAL_PD_SIZE;
num_pds = ICSSG_NUM_SPECIAL_PDS;
} else {
pd_size = ICSSG_NORMAL_PD_SIZE;
num_pds = ICSSG_NUM_NORMAL_PDS;
}
for (i = 0; i < num_pds; i++) {
memset(pd, 0, pd_size);
pdword[0] &= ICSSG_FLAG_MASK;
pdword[0] |= mp->flags;
pdaddr = mp->pd_addr_start + i * pd_size;
memcpy_toio(smem + pdaddr, pd, pd_size);
queue = mp->queue;
regmap_write(miig_rt, ICSSG_QUEUE_OFFSET + 4 * queue,
pdaddr);
}
}
}
void icssg_config_ipg(struct prueth_emac *emac)
{
struct prueth *prueth = emac->prueth;
int slice = prueth_emac_slice(emac);
u32 ipg;
switch (emac->speed) {
case SPEED_1000:
ipg = emac->is_sr1 ? MII_RT_TX_IPG_1G_SR1 : MII_RT_TX_IPG_1G;
break;
case SPEED_100:
ipg = emac->is_sr1 ? MII_RT_TX_IPG_100M_SR1 : MII_RT_TX_IPG_100M;
break;
case SPEED_10:
/* Firmware hardcodes IPG for SR1.0 */
if (emac->is_sr1)
return;
/* IPG for 10M is same as 100M */
ipg = MII_RT_TX_IPG_100M;
break;
default:
/* Other links speeds not supported */
netdev_err(emac->ndev, "Unsupported link speed\n");
return;
}
icssg_mii_update_ipg(prueth->mii_rt, slice, ipg);
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_config_ipg);
static void emac_r30_cmd_init(struct prueth_emac *emac)
{
struct icssg_r30_cmd __iomem *p;
int i;
p = emac->dram.va + MGR_R30_CMD_OFFSET;
for (i = 0; i < 4; i++)
writel(EMAC_NONE, &p->cmd[i]);
}
static int emac_r30_is_done(struct prueth_emac *emac)
{
const struct icssg_r30_cmd __iomem *p;
u32 cmd;
int i;
p = emac->dram.va + MGR_R30_CMD_OFFSET;
for (i = 0; i < 4; i++) {
cmd = readl(&p->cmd[i]);
if (cmd != EMAC_NONE)
return 0;
}
return 1;
}
static int prueth_fw_offload_buffer_setup(struct prueth_emac *emac)
{
struct icssg_buffer_pool_cfg __iomem *bpool_cfg;
struct icssg_rxq_ctx __iomem *rxq_ctx;
struct prueth *prueth = emac->prueth;
int slice = prueth_emac_slice(emac);
u32 addr;
int i;
addr = lower_32_bits(prueth->msmcram.pa);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
if (slice) {
if (prueth->pdata.banked_ms_ram)
addr += MSMC_RAM_BANK_SIZE;
else
addr += PRUETH_SW_TOTAL_BUF_SIZE_PER_SLICE;
}
if (addr % SZ_64K) {
dev_warn(prueth->dev, "buffer pool needs to be 64KB aligned\n");
return -EINVAL;
}
bpool_cfg = emac->dram.va + BUFFER_POOL_0_ADDR_OFFSET;
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Configure buffer pools for forwarding buffers
* - used by firmware to store packets to be forwarded to other port
* - 8 total pools per slice
*/
for (i = 0; i < PRUETH_NUM_FWD_BUF_POOLS_PER_SLICE; i++) {
writel(addr, &bpool_cfg[i].addr);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
writel(PRUETH_SW_FWD_BUF_POOL_SIZE, &bpool_cfg[i].len);
addr += PRUETH_SW_FWD_BUF_POOL_SIZE;
}
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Configure buffer pools for Local Injection buffers
* - used by firmware to store packets received from host core
* - 16 total pools per slice
*/
for (i = 0; i < PRUETH_NUM_LI_BUF_POOLS_PER_SLICE; i++) {
int cfg_idx = i + PRUETH_NUM_FWD_BUF_POOLS_PER_SLICE;
/* The driver only uses first 4 queues per PRU,
* so only initialize buffer for them
*/
if ((i % PRUETH_NUM_LI_BUF_POOLS_PER_PORT_PER_SLICE)
< PRUETH_SW_USED_LI_BUF_POOLS_PER_PORT_PER_SLICE) {
writel(addr, &bpool_cfg[cfg_idx].addr);
writel(PRUETH_SW_LI_BUF_POOL_SIZE,
&bpool_cfg[cfg_idx].len);
addr += PRUETH_SW_LI_BUF_POOL_SIZE;
} else {
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
writel(0, &bpool_cfg[cfg_idx].addr);
writel(0, &bpool_cfg[cfg_idx].len);
}
}
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Express RX buffer queue
* - used by firmware to store express packets to be transmitted
* to the host core
*/
rxq_ctx = emac->dram.va + HOST_RX_Q_EXP_CONTEXT_OFFSET;
for (i = 0; i < 3; i++)
writel(addr, &rxq_ctx->start[i]);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
addr += PRUETH_SW_HOST_EXP_BUF_POOL_SIZE;
writel(addr, &rxq_ctx->end);
/* Pre-emptible RX buffer queue
* - used by firmware to store preemptible packets to be transmitted
* to the host core
*/
rxq_ctx = emac->dram.va + HOST_RX_Q_PRE_CONTEXT_OFFSET;
for (i = 0; i < 3; i++)
writel(addr, &rxq_ctx->start[i]);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
addr += PRUETH_SW_HOST_PRE_BUF_POOL_SIZE;
writel(addr, &rxq_ctx->end);
/* Set pointer for default dropped packet write
* - used by firmware to temporarily store packet to be dropped
*/
rxq_ctx = emac->dram.va + DEFAULT_MSMC_Q_OFFSET;
writel(addr, &rxq_ctx->start[0]);
return 0;
}
static int prueth_emac_buffer_setup(struct prueth_emac *emac)
{
struct icssg_buffer_pool_cfg __iomem *bpool_cfg;
struct icssg_rxq_ctx __iomem *rxq_ctx;
struct prueth *prueth = emac->prueth;
int slice = prueth_emac_slice(emac);
u32 addr;
int i;
addr = lower_32_bits(prueth->msmcram.pa);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
if (slice) {
if (prueth->pdata.banked_ms_ram)
addr += MSMC_RAM_BANK_SIZE;
else
addr += PRUETH_EMAC_TOTAL_BUF_SIZE_PER_SLICE;
}
if (addr % SZ_64K) {
dev_warn(prueth->dev, "buffer pool needs to be 64KB aligned\n");
return -EINVAL;
}
bpool_cfg = emac->dram.va + BUFFER_POOL_0_ADDR_OFFSET;
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Configure buffer pools for forwarding buffers
* - in mac mode - no forwarding so initialize all pools to 0
* - 8 total pools per slice
*/
for (i = 0; i < PRUETH_NUM_FWD_BUF_POOLS_PER_SLICE; i++) {
writel(0, &bpool_cfg[i].addr);
writel(0, &bpool_cfg[i].len);
}
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Configure buffer pools for Local Injection buffers
* - used by firmware to store packets received from host core
* - 16 total pools per slice
*/
bpool_cfg = emac->dram.va + BUFFER_POOL_0_ADDR_OFFSET;
for (i = 0; i < PRUETH_NUM_LI_BUF_POOLS_PER_SLICE; i++) {
int cfg_idx = i + PRUETH_NUM_FWD_BUF_POOLS_PER_SLICE;
/* In EMAC mode, only first 4 buffers are used,
* as 1 slice needs to handle only 1 port
*/
if (i < PRUETH_EMAC_USED_LI_BUF_POOLS_PER_PORT_PER_SLICE) {
writel(addr, &bpool_cfg[cfg_idx].addr);
writel(PRUETH_EMAC_LI_BUF_POOL_SIZE,
&bpool_cfg[cfg_idx].len);
addr += PRUETH_EMAC_LI_BUF_POOL_SIZE;
} else {
writel(0, &bpool_cfg[cfg_idx].addr);
writel(0, &bpool_cfg[cfg_idx].len);
}
}
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Express RX buffer queue
* - used by firmware to store express packets to be transmitted
* to host core
*/
rxq_ctx = emac->dram.va + HOST_RX_Q_EXP_CONTEXT_OFFSET;
for (i = 0; i < 3; i++)
writel(addr, &rxq_ctx->start[i]);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
addr += PRUETH_EMAC_HOST_EXP_BUF_POOL_SIZE;
writel(addr, &rxq_ctx->end);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Pre-emptible RX buffer queue
* - used by firmware to store preemptible packets to be transmitted
* to host core
*/
rxq_ctx = emac->dram.va + HOST_RX_Q_PRE_CONTEXT_OFFSET;
for (i = 0; i < 3; i++)
writel(addr, &rxq_ctx->start[i]);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
addr += PRUETH_EMAC_HOST_PRE_BUF_POOL_SIZE;
writel(addr, &rxq_ctx->end);
net: ti: icssg-prueth: Fix buffer allocation for ICSSG Fixes overlapping buffer allocation for ICSSG peripheral used for storing packets to be received/transmitted. There are 3 buffers: 1. Buffer for Locally Injected Packets 2. Buffer for Forwarding Packets 3. Buffer for Host Egress Packets In existing allocation buffers for 2. and 3. are overlapping causing packet corruption. Packet corruption observations: During tcp iperf testing, due to overlapping buffers the received ack packet overwrites the packet to be transmitted. So, we see packets on wire with the ack packet content inside the content of next TCP packet from sender device. Details for AM64x switch mode: -> Allocation by existing driver: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 | | | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 | | | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 | | Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 | | | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 | | | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 | | Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ --> here 16, 17, 18, 19 overlapping with below express buffer +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping | PRE | 70030000 | 70033800 | 70034000 | 70037800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 00000000 | 00000000 | <-- Field not configured +---------------------+----------+----------+ -> Allocation this patch brings: +---------+-------------------------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------+--------------+--------+------+--------------+--------+ | | Slot | Base Address | Size | Slot | Base Address | Size | |---------+------+--------------+--------+------+--------------+--------+ | | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 | | | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 | | | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 | | FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 | | Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 | | | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 | | | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 | | | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 | +---------+------+--------------+--------+------+--------------+--------+ | | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 | | | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 | | | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 | | Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 | | LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 | | Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 | | | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 | | | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ | | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 | | | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 | | | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 | | Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 | | LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 | | Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 | | | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 | | | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 | +---------+------+--------------+--------+------+--------------+--------+ +-----+-----------------------------------------------+ | | SLICE 0 | SLICE 1 | | +------------+----------+------------+----------+ | | Start addr | End addr | Start addr | End addr | +-----+------------+----------+------------+----------+ | EXP | 70018000 | 7001C000 | 70058000 | 7005C000 | | PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 | +-----+------------+----------+------------+----------+ +---------------------+----------+----------+ | | SLICE 0 | SLICE 1 | +---------------------+----------+----------+ | Default Drop Offset | 7001F800 | 7005F800 | +---------------------+----------+----------+ Rootcause: missing buffer configuration for Express frames in function: prueth_fw_offload_buffer_setup() Details: Driver implements two distinct buffer configuration functions that are invoked based on the driver state and ICSSG firmware:- - prueth_fw_offload_buffer_setup() - prueth_emac_buffer_setup() During initialization, driver creates standard network interfaces (netdevs) and configures buffers via prueth_emac_buffer_setup(). This function properly allocates and configures all required memory regions including: - LI buffers - Express packet buffers - Preemptible packet buffers However, when the driver transitions to an offload mode (switch/HSR/PRP), buffer reconfiguration is handled by prueth_fw_offload_buffer_setup(). This function does not reconfigure the buffer regions required for Express packets, leading to incorrect buffer allocation. Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware") Signed-off-by: Himanshu Mittal <h-mittal1@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-07-17 15:12:20 +05:30
/* Set pointer for default dropped packet write
* - used by firmware to temporarily store packet to be dropped
*/
rxq_ctx = emac->dram.va + DEFAULT_MSMC_Q_OFFSET;
writel(addr, &rxq_ctx->start[0]);
return 0;
}
net: ti: icssg-prueth: Fix firmware load sequence. Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0 and SLICE1. Currently whenever any ICSSG interface comes up we load the respective firmwares to PRU cores and whenever interface goes down, we stop the resective cores. Due to this, when SLICE0 goes down while SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is stopped. This results in clock jump for SLICE1 interface as the timesync related operations are no longer running. As there are interdependencies between SLICE0 and SLICE1 firmwares, fix this by running both PRU0 and PRU1 firmwares as long as at least 1 ICSSG interface is up. Add new flag in prueth struct to check if all firmwares are running and remove the old flag (fw_running). Use emacs_initialized as reference count to load the firmwares for the first and last interface up/down. Moving init_emac_mode and fw_offload_mode API outside of icssg_config to icssg_common_start API as they need to be called only once per firmware boot. Change prueth_emac_restart() to return error code and add error prints inside the caller of this functions in case of any failures. Move prueth_emac_stop() from common to sr1 driver. sr1 and sr2 drivers have different logic handling for stopping the firmwares. While sr1 driver is dependent on emac structure to stop the corresponding pru cores for that slice, for sr2 all the pru cores of both the slices are stopped and is not dependent on emac. So the prueth_emac_stop() function is no longer common and can be moved to sr1 driver. Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Meghana Malladi <m-malladi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-12-23 20:45:49 +05:30
void icssg_init_emac_mode(struct prueth *prueth)
{
/* When the device is configured as a bridge and it is being brought
* back to the emac mode, the host mac address has to be set as 0.
*/
u32 addr = prueth->shram.pa + EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET;
int i;
u8 mac[ETH_ALEN] = { 0 };
/* Set VLAN TABLE address base */
regmap_update_bits(prueth->miig_rt, FDB_GEN_CFG1, SMEM_VLAN_OFFSET_MASK,
addr << SMEM_VLAN_OFFSET);
/* Set enable VLAN aware mode, and FDBs for all PRUs */
regmap_write(prueth->miig_rt, FDB_GEN_CFG2, (FDB_PRU0_EN | FDB_PRU1_EN | FDB_HOST_EN));
prueth->vlan_tbl = (struct prueth_vlan_tbl __force *)(prueth->shram.va +
EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET);
for (i = 0; i < SZ_4K - 1; i++) {
prueth->vlan_tbl[i].fid = i;
prueth->vlan_tbl[i].fid_c1 = 0;
}
/* Clear host MAC address */
icssg_class_set_host_mac_addr(prueth->miig_rt, mac);
}
net: ti: icssg-prueth: Fix firmware load sequence. Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0 and SLICE1. Currently whenever any ICSSG interface comes up we load the respective firmwares to PRU cores and whenever interface goes down, we stop the resective cores. Due to this, when SLICE0 goes down while SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is stopped. This results in clock jump for SLICE1 interface as the timesync related operations are no longer running. As there are interdependencies between SLICE0 and SLICE1 firmwares, fix this by running both PRU0 and PRU1 firmwares as long as at least 1 ICSSG interface is up. Add new flag in prueth struct to check if all firmwares are running and remove the old flag (fw_running). Use emacs_initialized as reference count to load the firmwares for the first and last interface up/down. Moving init_emac_mode and fw_offload_mode API outside of icssg_config to icssg_common_start API as they need to be called only once per firmware boot. Change prueth_emac_restart() to return error code and add error prints inside the caller of this functions in case of any failures. Move prueth_emac_stop() from common to sr1 driver. sr1 and sr2 drivers have different logic handling for stopping the firmwares. While sr1 driver is dependent on emac structure to stop the corresponding pru cores for that slice, for sr2 all the pru cores of both the slices are stopped and is not dependent on emac. So the prueth_emac_stop() function is no longer common and can be moved to sr1 driver. Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Meghana Malladi <m-malladi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-12-23 20:45:49 +05:30
EXPORT_SYMBOL_GPL(icssg_init_emac_mode);
net: ti: icssg-prueth: Fix firmware load sequence. Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0 and SLICE1. Currently whenever any ICSSG interface comes up we load the respective firmwares to PRU cores and whenever interface goes down, we stop the resective cores. Due to this, when SLICE0 goes down while SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is stopped. This results in clock jump for SLICE1 interface as the timesync related operations are no longer running. As there are interdependencies between SLICE0 and SLICE1 firmwares, fix this by running both PRU0 and PRU1 firmwares as long as at least 1 ICSSG interface is up. Add new flag in prueth struct to check if all firmwares are running and remove the old flag (fw_running). Use emacs_initialized as reference count to load the firmwares for the first and last interface up/down. Moving init_emac_mode and fw_offload_mode API outside of icssg_config to icssg_common_start API as they need to be called only once per firmware boot. Change prueth_emac_restart() to return error code and add error prints inside the caller of this functions in case of any failures. Move prueth_emac_stop() from common to sr1 driver. sr1 and sr2 drivers have different logic handling for stopping the firmwares. While sr1 driver is dependent on emac structure to stop the corresponding pru cores for that slice, for sr2 all the pru cores of both the slices are stopped and is not dependent on emac. So the prueth_emac_stop() function is no longer common and can be moved to sr1 driver. Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Meghana Malladi <m-malladi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-12-23 20:45:49 +05:30
void icssg_init_fw_offload_mode(struct prueth *prueth)
{
u32 addr = prueth->shram.pa + EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET;
int i;
/* Set VLAN TABLE address base */
regmap_update_bits(prueth->miig_rt, FDB_GEN_CFG1, SMEM_VLAN_OFFSET_MASK,
addr << SMEM_VLAN_OFFSET);
/* Set enable VLAN aware mode, and FDBs for all PRUs */
regmap_write(prueth->miig_rt, FDB_GEN_CFG2, FDB_EN_ALL);
prueth->vlan_tbl = (struct prueth_vlan_tbl __force *)(prueth->shram.va +
EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET);
for (i = 0; i < SZ_4K - 1; i++) {
prueth->vlan_tbl[i].fid = i;
prueth->vlan_tbl[i].fid_c1 = 0;
}
if (prueth->hw_bridge_dev)
icssg_class_set_host_mac_addr(prueth->miig_rt, prueth->hw_bridge_dev->dev_addr);
icssg_set_pvid(prueth, prueth->default_vlan, PRUETH_PORT_HOST);
}
net: ti: icssg-prueth: Fix firmware load sequence. Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0 and SLICE1. Currently whenever any ICSSG interface comes up we load the respective firmwares to PRU cores and whenever interface goes down, we stop the resective cores. Due to this, when SLICE0 goes down while SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is stopped. This results in clock jump for SLICE1 interface as the timesync related operations are no longer running. As there are interdependencies between SLICE0 and SLICE1 firmwares, fix this by running both PRU0 and PRU1 firmwares as long as at least 1 ICSSG interface is up. Add new flag in prueth struct to check if all firmwares are running and remove the old flag (fw_running). Use emacs_initialized as reference count to load the firmwares for the first and last interface up/down. Moving init_emac_mode and fw_offload_mode API outside of icssg_config to icssg_common_start API as they need to be called only once per firmware boot. Change prueth_emac_restart() to return error code and add error prints inside the caller of this functions in case of any failures. Move prueth_emac_stop() from common to sr1 driver. sr1 and sr2 drivers have different logic handling for stopping the firmwares. While sr1 driver is dependent on emac structure to stop the corresponding pru cores for that slice, for sr2 all the pru cores of both the slices are stopped and is not dependent on emac. So the prueth_emac_stop() function is no longer common and can be moved to sr1 driver. Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Meghana Malladi <m-malladi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-12-23 20:45:49 +05:30
EXPORT_SYMBOL_GPL(icssg_init_fw_offload_mode);
int icssg_config(struct prueth *prueth, struct prueth_emac *emac, int slice)
{
void __iomem *config = emac->dram.va + ICSSG_CONFIG_OFFSET;
struct icssg_flow_cfg __iomem *flow_cfg;
int ret;
memset_io(config, 0, TAS_GATE_MASK_LIST0);
icssg_miig_queues_init(prueth, slice);
emac->speed = SPEED_1000;
emac->duplex = DUPLEX_FULL;
if (!phy_interface_mode_is_rgmii(emac->phy_if)) {
emac->speed = SPEED_100;
emac->duplex = DUPLEX_FULL;
}
regmap_update_bits(prueth->miig_rt, ICSSG_CFG_OFFSET,
ICSSG_CFG_DEFAULT, ICSSG_CFG_DEFAULT);
icssg_miig_set_interface_mode(prueth->miig_rt, slice, emac->phy_if);
if (prueth->is_switch_mode || prueth->is_hsr_offload_mode)
icssg_config_mii_init_fw_offload(emac);
else
icssg_config_mii_init(emac);
icssg_config_ipg(emac);
icssg_update_rgmii_cfg(prueth->miig_rt, emac);
/* set GPI mode */
pruss_cfg_gpimode(prueth->pruss, prueth->pru_id[slice],
PRUSS_GPI_MODE_MII);
/* enable XFR shift for PRU and RTU */
pruss_cfg_xfr_enable(prueth->pruss, PRU_TYPE_PRU, true);
pruss_cfg_xfr_enable(prueth->pruss, PRU_TYPE_RTU, true);
/* set C28 to 0x100 */
pru_rproc_set_ctable(prueth->pru[slice], PRU_C28, 0x100 << 8);
pru_rproc_set_ctable(prueth->rtu[slice], PRU_C28, 0x100 << 8);
pru_rproc_set_ctable(prueth->txpru[slice], PRU_C28, 0x100 << 8);
flow_cfg = config + PSI_L_REGULAR_FLOW_ID_BASE_OFFSET;
writew(emac->rx_flow_id_base, &flow_cfg->rx_base_flow);
writew(0, &flow_cfg->mgm_base_flow);
writeb(0, config + SPL_PKT_DEFAULT_PRIORITY);
writeb(0, config + QUEUE_NUM_UNTAGGED);
if (prueth->is_switch_mode || prueth->is_hsr_offload_mode)
ret = prueth_fw_offload_buffer_setup(emac);
else
ret = prueth_emac_buffer_setup(emac);
if (ret)
return ret;
emac_r30_cmd_init(emac);
return 0;
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_config);
/* Bitmask for ICSSG r30 commands */
static const struct icssg_r30_cmd emac_r32_bitmask[] = {
{{0xffff0004, 0xffff0100, 0xffff0004, EMAC_NONE}}, /* EMAC_PORT_DISABLE */
{{0xfffb0040, 0xfeff0200, 0xfeff0200, EMAC_NONE}}, /* EMAC_PORT_BLOCK */
{{0xffbb0000, 0xfcff0000, 0xdcfb0000, EMAC_NONE}}, /* EMAC_PORT_FORWARD */
{{0xffbb0000, 0xfcff0000, 0xfcff2000, EMAC_NONE}}, /* EMAC_PORT_FORWARD_WO_LEARNING */
{{0xffff0001, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT ALL */
{{0xfffe0002, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT TAGGED */
{{0xfffc0000, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT UNTAGGED and PRIO */
{{EMAC_NONE, 0xffff0020, EMAC_NONE, EMAC_NONE}}, /* TAS Trigger List change */
{{EMAC_NONE, 0xdfff1000, EMAC_NONE, EMAC_NONE}}, /* TAS set state ENABLE*/
{{EMAC_NONE, 0xefff2000, EMAC_NONE, EMAC_NONE}}, /* TAS set state RESET*/
{{EMAC_NONE, 0xcfff0000, EMAC_NONE, EMAC_NONE}}, /* TAS set state DISABLE*/
{{EMAC_NONE, EMAC_NONE, 0xffff0400, EMAC_NONE}}, /* UC flooding ENABLE*/
{{EMAC_NONE, EMAC_NONE, 0xfbff0000, EMAC_NONE}}, /* UC flooding DISABLE*/
{{EMAC_NONE, EMAC_NONE, 0xffff0800, EMAC_NONE}}, /* MC flooding ENABLE*/
{{EMAC_NONE, EMAC_NONE, 0xf7ff0000, EMAC_NONE}}, /* MC flooding DISABLE*/
{{EMAC_NONE, 0xffff4000, EMAC_NONE, EMAC_NONE}}, /* Preemption on Tx ENABLE*/
{{EMAC_NONE, 0xbfff0000, EMAC_NONE, EMAC_NONE}}, /* Preemption on Tx DISABLE*/
{{0xffff0010, EMAC_NONE, 0xffff0010, EMAC_NONE}}, /* VLAN AWARE*/
{{0xffef0000, EMAC_NONE, 0xffef0000, EMAC_NONE}}, /* VLAN UNWARE*/
{{0xffff2000, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* HSR_RX_OFFLOAD_ENABLE */
{{0xdfff0000, EMAC_NONE, EMAC_NONE, EMAC_NONE}} /* HSR_RX_OFFLOAD_DISABLE */
};
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
int icssg_set_port_state(struct prueth_emac *emac,
enum icssg_port_state_cmd cmd)
{
struct icssg_r30_cmd __iomem *p;
int ret = -ETIMEDOUT;
int done = 0;
int i;
p = emac->dram.va + MGR_R30_CMD_OFFSET;
if (cmd >= ICSSG_EMAC_PORT_MAX_COMMANDS) {
netdev_err(emac->ndev, "invalid port command\n");
return -EINVAL;
}
/* only one command at a time allowed to firmware */
mutex_lock(&emac->cmd_lock);
for (i = 0; i < 4; i++)
writel(emac_r32_bitmask[cmd].cmd[i], &p->cmd[i]);
/* wait for done */
ret = read_poll_timeout(emac_r30_is_done, done, done == 1,
1000, 10000, false, emac);
if (ret == -ETIMEDOUT)
netdev_err(emac->ndev, "timeout waiting for command done\n");
mutex_unlock(&emac->cmd_lock);
return ret;
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_set_port_state);
void icssg_config_half_duplex(struct prueth_emac *emac)
{
u32 val;
if (!emac->half_duplex)
return;
val = get_random_u32();
writel(val, emac->dram.va + HD_RAND_SEED_OFFSET);
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_config_half_duplex);
void icssg_config_set_speed(struct prueth_emac *emac)
{
u8 fw_speed;
switch (emac->speed) {
case SPEED_1000:
fw_speed = FW_LINK_SPEED_1G;
break;
case SPEED_100:
fw_speed = FW_LINK_SPEED_100M;
break;
case SPEED_10:
fw_speed = FW_LINK_SPEED_10M;
break;
default:
/* Other links speeds not supported */
netdev_err(emac->ndev, "Unsupported link speed\n");
return;
}
if (emac->duplex == DUPLEX_HALF)
fw_speed |= FW_LINK_SPEED_HD;
writeb(fw_speed, emac->dram.va + PORT_LINK_SPEED_OFFSET);
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_config_set_speed);
int icssg_send_fdb_msg(struct prueth_emac *emac, struct mgmt_cmd *cmd,
struct mgmt_cmd_rsp *rsp)
{
struct prueth *prueth = emac->prueth;
int slice = prueth_emac_slice(emac);
int addr, ret;
addr = icssg_queue_pop(prueth, slice == 0 ?
ICSSG_CMD_POP_SLICE0 : ICSSG_CMD_POP_SLICE1);
if (addr < 0)
return addr;
/* First 4 bytes have FW owned buffer linking info which should
* not be touched
*/
memcpy_toio(prueth->shram.va + addr + 4, cmd, sizeof(*cmd));
icssg_queue_push(prueth, slice == 0 ?
ICSSG_CMD_PUSH_SLICE0 : ICSSG_CMD_PUSH_SLICE1, addr);
ret = read_poll_timeout(icssg_queue_pop, addr, addr >= 0,
2000, 20000000, false, prueth, slice == 0 ?
ICSSG_RSP_POP_SLICE0 : ICSSG_RSP_POP_SLICE1);
if (ret) {
netdev_err(emac->ndev, "Timedout sending HWQ message\n");
return ret;
}
memcpy_fromio(rsp, prueth->shram.va + addr, sizeof(*rsp));
/* Return buffer back for to pool */
icssg_queue_push(prueth, slice == 0 ?
ICSSG_RSP_PUSH_SLICE0 : ICSSG_RSP_PUSH_SLICE1, addr);
return 0;
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_send_fdb_msg);
static void icssg_fdb_setup(struct prueth_emac *emac, struct mgmt_cmd *fdb_cmd,
const unsigned char *addr, u8 fid, int cmd)
{
int slice = prueth_emac_slice(emac);
u8 mac_fid[ETH_ALEN + 2];
u16 fdb_slot;
ether_addr_copy(mac_fid, addr);
/* 1-1 VID-FID mapping is already setup */
mac_fid[ETH_ALEN] = fid;
mac_fid[ETH_ALEN + 1] = 0;
fdb_slot = bitrev32(crc32_le(0, mac_fid, 8)) & PRUETH_SWITCH_FDB_MASK;
fdb_cmd->header = ICSSG_FW_MGMT_CMD_HEADER;
fdb_cmd->type = ICSSG_FW_MGMT_FDB_CMD_TYPE;
fdb_cmd->seqnum = ++(emac->prueth->icssg_hwcmdseq);
fdb_cmd->param = cmd;
fdb_cmd->param |= (slice << 4);
memcpy(&fdb_cmd->cmd_args[0], addr, 4);
memcpy(&fdb_cmd->cmd_args[1], &addr[4], 2);
fdb_cmd->cmd_args[2] = fdb_slot;
netdev_dbg(emac->ndev, "MAC %pM slot %X FID %X\n", addr, fdb_slot, fid);
}
int icssg_fdb_add_del(struct prueth_emac *emac, const unsigned char *addr,
u8 vid, u8 fid_c2, bool add)
{
struct mgmt_cmd_rsp fdb_cmd_rsp = { 0 };
struct mgmt_cmd fdb_cmd = { 0 };
u8 fid = vid;
int ret;
icssg_fdb_setup(emac, &fdb_cmd, addr, fid, add ? ICSS_CMD_ADD_FDB : ICSS_CMD_DEL_FDB);
fid_c2 |= ICSSG_FDB_ENTRY_VALID;
fdb_cmd.cmd_args[1] |= ((fid << 16) | (fid_c2 << 24));
ret = icssg_send_fdb_msg(emac, &fdb_cmd, &fdb_cmd_rsp);
if (ret)
return ret;
WARN_ON(fdb_cmd.seqnum != fdb_cmd_rsp.seqnum);
if (fdb_cmd_rsp.status == 1)
return 0;
return -EINVAL;
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_fdb_add_del);
int icssg_fdb_lookup(struct prueth_emac *emac, const unsigned char *addr,
u8 vid)
{
struct mgmt_cmd_rsp fdb_cmd_rsp = { 0 };
struct mgmt_cmd fdb_cmd = { 0 };
struct prueth_fdb_slot *slot;
u8 fid = vid;
int ret, i;
icssg_fdb_setup(emac, &fdb_cmd, addr, fid, ICSS_CMD_GET_FDB_SLOT);
fdb_cmd.cmd_args[1] |= fid << 16;
ret = icssg_send_fdb_msg(emac, &fdb_cmd, &fdb_cmd_rsp);
if (ret)
return ret;
WARN_ON(fdb_cmd.seqnum != fdb_cmd_rsp.seqnum);
slot = (struct prueth_fdb_slot __force *)(emac->dram.va + FDB_CMD_BUFFER);
for (i = 0; i < 4; i++) {
if (ether_addr_equal(addr, slot->mac) && vid == slot->fid)
return (slot->fid_c2 & ~ICSSG_FDB_ENTRY_VALID);
slot++;
}
return 0;
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_fdb_lookup);
void icssg_vtbl_modify(struct prueth_emac *emac, u8 vid, u8 port_mask,
u8 untag_mask, bool add)
{
struct prueth *prueth = emac->prueth;
struct prueth_vlan_tbl *tbl;
u8 fid_c1;
tbl = prueth->vlan_tbl;
spin_lock(&prueth->vtbl_lock);
fid_c1 = tbl[vid].fid_c1;
/* FID_C1: bit0..2 port membership mask,
* bit3..5 tagging mask for each port
* bit6 Stream VID (not handled currently)
* bit7 MC flood (not handled currently)
*/
if (add) {
fid_c1 |= (port_mask | port_mask << 3);
fid_c1 &= ~(untag_mask << 3);
} else {
fid_c1 &= ~(port_mask | port_mask << 3);
}
tbl[vid].fid_c1 = fid_c1;
spin_unlock(&prueth->vtbl_lock);
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_vtbl_modify);
u16 icssg_get_pvid(struct prueth_emac *emac)
{
struct prueth *prueth = emac->prueth;
u32 pvid;
if (emac->port_id == PRUETH_PORT_MII0)
pvid = readl(prueth->shram.va + EMAC_ICSSG_SWITCH_PORT1_DEFAULT_VLAN_OFFSET);
else
pvid = readl(prueth->shram.va + EMAC_ICSSG_SWITCH_PORT2_DEFAULT_VLAN_OFFSET);
pvid = pvid >> 24;
return pvid;
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_get_pvid);
void icssg_set_pvid(struct prueth *prueth, u8 vid, u8 port)
{
u32 pvid;
/* only 256 VLANs are supported */
pvid = (u32 __force)cpu_to_be32((ETH_P_8021Q << 16) | (vid & 0xff));
if (port == PRUETH_PORT_MII0)
writel(pvid, prueth->shram.va + EMAC_ICSSG_SWITCH_PORT1_DEFAULT_VLAN_OFFSET);
else if (port == PRUETH_PORT_MII1)
writel(pvid, prueth->shram.va + EMAC_ICSSG_SWITCH_PORT2_DEFAULT_VLAN_OFFSET);
else
writel(pvid, prueth->shram.va + EMAC_ICSSG_SWITCH_PORT0_DEFAULT_VLAN_OFFSET);
}
net: ti: icssg-prueth: Split out common object into module icssg_prueth.c and icssg_prueth_sr1.c drivers use multiple common .c files. These common objects are getting added to multiple modules. As a result when both drivers are enabled in .config, below warning is seen. drivers/net/ethernet/ti/Makefile: icssg/icssg_common.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_classifier.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_config.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_mii_cfg.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_stats.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 drivers/net/ethernet/ti/Makefile: icssg/icssg_ethtool.o is added to multiple modules: icssg-prueth icssg-prueth-sr1 Fix this by building a new module (icssg.o) for all the common objects. Both the driver can then depend on this common module. Some APIs being exported have emac_ as the prefix which may result into confusion with other existing APIs with emac_ prefix, to avoid confusion, rename the APIs being exported with emac_ to icssg_ prefix. This also fixes below error seen when both drivers are built. ERROR: modpost: "icssg_queue_pop" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! ERROR: modpost: "icssg_queue_push" [drivers/net/ethernet/ti/icssg-prueth-sr1.ko] undefined! Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info> Closes: https://lore.kernel.org/oe-kbuild-all/202405182038.ncf1mL7Z-lkp@intel.com/ Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-12 17:36:36 +05:30
EXPORT_SYMBOL_GPL(icssg_set_pvid);
net: ti: icssg-prueth: Fix firmware load sequence. Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0 and SLICE1. Currently whenever any ICSSG interface comes up we load the respective firmwares to PRU cores and whenever interface goes down, we stop the resective cores. Due to this, when SLICE0 goes down while SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is stopped. This results in clock jump for SLICE1 interface as the timesync related operations are no longer running. As there are interdependencies between SLICE0 and SLICE1 firmwares, fix this by running both PRU0 and PRU1 firmwares as long as at least 1 ICSSG interface is up. Add new flag in prueth struct to check if all firmwares are running and remove the old flag (fw_running). Use emacs_initialized as reference count to load the firmwares for the first and last interface up/down. Moving init_emac_mode and fw_offload_mode API outside of icssg_config to icssg_common_start API as they need to be called only once per firmware boot. Change prueth_emac_restart() to return error code and add error prints inside the caller of this functions in case of any failures. Move prueth_emac_stop() from common to sr1 driver. sr1 and sr2 drivers have different logic handling for stopping the firmwares. While sr1 driver is dependent on emac structure to stop the corresponding pru cores for that slice, for sr2 all the pru cores of both the slices are stopped and is not dependent on emac. So the prueth_emac_stop() function is no longer common and can be moved to sr1 driver. Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Meghana Malladi <m-malladi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-12-23 20:45:49 +05:30
int emac_fdb_flow_id_updated(struct prueth_emac *emac)
{
struct mgmt_cmd_rsp fdb_cmd_rsp = { 0 };
int slice = prueth_emac_slice(emac);
struct mgmt_cmd fdb_cmd = { 0 };
int ret;
fdb_cmd.header = ICSSG_FW_MGMT_CMD_HEADER;
fdb_cmd.type = ICSSG_FW_MGMT_FDB_CMD_TYPE_RX_FLOW;
fdb_cmd.seqnum = ++(emac->prueth->icssg_hwcmdseq);
fdb_cmd.param = 0;
fdb_cmd.param |= (slice << 4);
fdb_cmd.cmd_args[0] = 0;
ret = icssg_send_fdb_msg(emac, &fdb_cmd, &fdb_cmd_rsp);
if (ret)
return ret;
WARN_ON(fdb_cmd.seqnum != fdb_cmd_rsp.seqnum);
return fdb_cmd_rsp.status == 1 ? 0 : -EINVAL;
}
EXPORT_SYMBOL_GPL(emac_fdb_flow_id_updated);