linux/drivers/net/can/rcar/rcar_canfd.c

2251 lines
64 KiB
C
Raw Permalink Normal View History

// SPDX-License-Identifier: GPL-2.0+
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Renesas R-Car CAN FD device driver
*
* Copyright (C) 2015 Renesas Electronics Corp.
*/
/* The R-Car CAN FD controller can operate in either one of the below two modes
* - CAN FD only mode
* - Classical CAN (CAN 2.0) only mode
*
* This driver puts the controller in CAN FD only mode by default. In this
* mode, the controller acts as a CAN FD node that can also interoperate with
* CAN 2.0 nodes.
*
* To switch the controller to Classical CAN (CAN 2.0) only mode, add
* "renesas,no-can-fd" optional property to the device tree node. A h/w reset is
* also required to switch modes.
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
*
* Note: The h/w manual register naming convention is clumsy and not acceptable
* to use as it is in the driver. However, those names are added as comments
* wherever it is modified to a readable name.
*/
#include <linux/bitfield.h>
#include <linux/bitmap.h>
#include <linux/bitops.h>
#include <linux/can/dev.h>
#include <linux/clk.h>
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#include <linux/errno.h>
#include <linux/ethtool.h>
#include <linux/interrupt.h>
#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#include <linux/netdevice.h>
#include <linux/of.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/reset.h>
#include <linux/types.h>
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_DRV_NAME "rcar_canfd"
/* Global register bits */
/* RSCFDnCFDGRMCFG */
#define RCANFD_GRMCFG_RCMC BIT(0)
/* RSCFDnCFDGCFG / RSCFDnGCFG */
#define RCANFD_GCFG_EEFE BIT(6)
#define RCANFD_GCFG_CMPOC BIT(5) /* CAN FD only */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GCFG_DCS BIT(4)
#define RCANFD_GCFG_DCE BIT(1)
#define RCANFD_GCFG_TPRI BIT(0)
/* RSCFDnCFDGCTR / RSCFDnGCTR */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GCTR_TSRST BIT(16)
#define RCANFD_GCTR_CFMPOFIE BIT(11) /* CAN FD only */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GCTR_THLEIE BIT(10)
#define RCANFD_GCTR_MEIE BIT(9)
#define RCANFD_GCTR_DEIE BIT(8)
#define RCANFD_GCTR_GSLPR BIT(2)
#define RCANFD_GCTR_GMDC_MASK (0x3)
#define RCANFD_GCTR_GMDC_GOPM (0x0)
#define RCANFD_GCTR_GMDC_GRESET (0x1)
#define RCANFD_GCTR_GMDC_GTEST (0x2)
/* RSCFDnCFDGSTS / RSCFDnGSTS */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GSTS_GRAMINIT BIT(3)
#define RCANFD_GSTS_GSLPSTS BIT(2)
#define RCANFD_GSTS_GHLTSTS BIT(1)
#define RCANFD_GSTS_GRSTSTS BIT(0)
/* Non-operational status */
#define RCANFD_GSTS_GNOPM (BIT(0) | BIT(1) | BIT(2) | BIT(3))
/* RSCFDnCFDGERFL / RSCFDnGERFL */
#define RCANFD_GERFL_EEF GENMASK(23, 16)
#define RCANFD_GERFL_CMPOF BIT(3) /* CAN FD only */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GERFL_THLES BIT(2)
#define RCANFD_GERFL_MES BIT(1)
#define RCANFD_GERFL_DEF BIT(0)
#define RCANFD_GERFL_ERR(gpriv, x) \
({\
typeof(gpriv) (_gpriv) = (gpriv); \
((x) & ((FIELD_PREP(RCANFD_GERFL_EEF, (_gpriv)->channels_mask)) | \
RCANFD_GERFL_MES | ((_gpriv)->fdmode ? RCANFD_GERFL_CMPOF : 0))); \
})
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* AFL Rx rules registers */
/* RSCFDnCFDGAFLECTR / RSCFDnGAFLECTR */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GAFLECTR_AFLDAE BIT(8)
#define RCANFD_GAFLECTR_AFLPN(gpriv, page_num) ((page_num) & (gpriv)->info->max_aflpn)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDGAFLIDj / RSCFDnGAFLIDj */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GAFLID_GAFLLB BIT(29)
/* RSCFDnCFDGAFLP1_j / RSCFDnGAFLP1_j */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GAFLP1_GAFLFDP(x) (1 << (x))
/* Channel register bits */
/* RSCFDnCmCFG - Classical CAN only */
#define RCANFD_CFG_SJW(x) (((x) & 0x3) << 24)
#define RCANFD_CFG_TSEG2(x) (((x) & 0x7) << 20)
#define RCANFD_CFG_TSEG1(x) (((x) & 0xf) << 16)
#define RCANFD_CFG_BRP(x) (((x) & 0x3ff) << 0)
/* RSCFDnCFDCmNCFG - CAN FD only */
#define RCANFD_NCFG_NTSEG2(gpriv, x) \
(((x) & ((gpriv)->info->nom_bittiming->tseg2_max - 1)) << (gpriv)->info->sh->ntseg2)
#define RCANFD_NCFG_NTSEG1(gpriv, x) \
(((x) & ((gpriv)->info->nom_bittiming->tseg1_max - 1)) << (gpriv)->info->sh->ntseg1)
#define RCANFD_NCFG_NSJW(gpriv, x) \
(((x) & ((gpriv)->info->nom_bittiming->sjw_max - 1)) << (gpriv)->info->sh->nsjw)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_NCFG_NBRP(x) (((x) & 0x3ff) << 0)
/* RSCFDnCFDCmCTR / RSCFDnCmCTR */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_CCTR_CTME BIT(24)
#define RCANFD_CCTR_ERRD BIT(23)
#define RCANFD_CCTR_BOM_MASK (0x3 << 21)
#define RCANFD_CCTR_BOM_ISO (0x0 << 21)
#define RCANFD_CCTR_BOM_BENTRY (0x1 << 21)
#define RCANFD_CCTR_BOM_BEND (0x2 << 21)
#define RCANFD_CCTR_TDCVFIE BIT(19)
#define RCANFD_CCTR_SOCOIE BIT(18)
#define RCANFD_CCTR_EOCOIE BIT(17)
#define RCANFD_CCTR_TAIE BIT(16)
#define RCANFD_CCTR_ALIE BIT(15)
#define RCANFD_CCTR_BLIE BIT(14)
#define RCANFD_CCTR_OLIE BIT(13)
#define RCANFD_CCTR_BORIE BIT(12)
#define RCANFD_CCTR_BOEIE BIT(11)
#define RCANFD_CCTR_EPIE BIT(10)
#define RCANFD_CCTR_EWIE BIT(9)
#define RCANFD_CCTR_BEIE BIT(8)
#define RCANFD_CCTR_CSLPR BIT(2)
#define RCANFD_CCTR_CHMDC_MASK (0x3)
#define RCANFD_CCTR_CHDMC_COPM (0x0)
#define RCANFD_CCTR_CHDMC_CRESET (0x1)
#define RCANFD_CCTR_CHDMC_CHLT (0x2)
/* RSCFDnCFDCmSTS / RSCFDnCmSTS */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_CSTS_COMSTS BIT(7)
#define RCANFD_CSTS_RECSTS BIT(6)
#define RCANFD_CSTS_TRMSTS BIT(5)
#define RCANFD_CSTS_BOSTS BIT(4)
#define RCANFD_CSTS_EPSTS BIT(3)
#define RCANFD_CSTS_SLPSTS BIT(2)
#define RCANFD_CSTS_HLTSTS BIT(1)
#define RCANFD_CSTS_CRSTSTS BIT(0)
#define RCANFD_CSTS_TECCNT(x) (((x) >> 24) & 0xff)
#define RCANFD_CSTS_RECCNT(x) (((x) >> 16) & 0xff)
/* RSCFDnCFDCmERFL / RSCFDnCmERFL */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_CERFL_ADERR BIT(14)
#define RCANFD_CERFL_B0ERR BIT(13)
#define RCANFD_CERFL_B1ERR BIT(12)
#define RCANFD_CERFL_CERR BIT(11)
#define RCANFD_CERFL_AERR BIT(10)
#define RCANFD_CERFL_FERR BIT(9)
#define RCANFD_CERFL_SERR BIT(8)
#define RCANFD_CERFL_ALF BIT(7)
#define RCANFD_CERFL_BLF BIT(6)
#define RCANFD_CERFL_OVLF BIT(5)
#define RCANFD_CERFL_BORF BIT(4)
#define RCANFD_CERFL_BOEF BIT(3)
#define RCANFD_CERFL_EPF BIT(2)
#define RCANFD_CERFL_EWF BIT(1)
#define RCANFD_CERFL_BEF BIT(0)
#define RCANFD_CERFL_ERR(x) ((x) & (0x7fff)) /* above bits 14:0 */
/* RSCFDnCFDCmDCFG */
#define RCANFD_DCFG_DSJW(gpriv, x) (((x) & ((gpriv)->info->data_bittiming->sjw_max - 1)) << 24)
#define RCANFD_DCFG_DTSEG2(gpriv, x) \
(((x) & ((gpriv)->info->data_bittiming->tseg2_max - 1)) << (gpriv)->info->sh->dtseg2)
#define RCANFD_DCFG_DTSEG1(gpriv, x) \
(((x) & ((gpriv)->info->data_bittiming->tseg1_max - 1)) << (gpriv)->info->sh->dtseg1)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_DCFG_DBRP(x) (((x) & 0xff) << 0)
/* RSCFDnCFDCmFDCFG */
#define RCANFD_GEN4_FDCFG_CLOE BIT(30)
#define RCANFD_GEN4_FDCFG_FDOE BIT(28)
#define RCANFD_FDCFG_TDCO GENMASK(23, 16)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_FDCFG_TDCE BIT(9)
#define RCANFD_FDCFG_TDCOC BIT(8)
/* RSCFDnCFDCmFDSTS */
#define RCANFD_FDSTS_SOC GENMASK(31, 24)
#define RCANFD_FDSTS_EOC GENMASK(23, 16)
#define RCANFD_GEN4_FDSTS_TDCVF BIT(15)
#define RCANFD_GEN4_FDSTS_PNSTS GENMASK(13, 12)
#define RCANFD_FDSTS_SOCO BIT(9)
#define RCANFD_FDSTS_EOCO BIT(8)
#define RCANFD_FDSTS_TDCVF BIT(7)
#define RCANFD_FDSTS_TDCR GENMASK(7, 0)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDRFCCx */
#define RCANFD_RFCC_RFIM BIT(12)
#define RCANFD_RFCC_RFDC(x) (((x) & 0x7) << 8)
#define RCANFD_RFCC_RFPLS(x) (((x) & 0x7) << 4)
#define RCANFD_RFCC_RFIE BIT(1)
#define RCANFD_RFCC_RFE BIT(0)
/* RSCFDnCFDRFSTSx */
#define RCANFD_RFSTS_RFIF BIT(3)
#define RCANFD_RFSTS_RFMLT BIT(2)
#define RCANFD_RFSTS_RFFLL BIT(1)
#define RCANFD_RFSTS_RFEMP BIT(0)
/* RSCFDnCFDRFIDx */
#define RCANFD_RFID_RFIDE BIT(31)
#define RCANFD_RFID_RFRTR BIT(30)
/* RSCFDnCFDRFPTRx */
#define RCANFD_RFPTR_RFDLC(x) (((x) >> 28) & 0xf)
/* RSCFDnCFDRFFDSTSx */
#define RCANFD_RFFDSTS_RFFDF BIT(2)
#define RCANFD_RFFDSTS_RFBRS BIT(1)
#define RCANFD_RFFDSTS_RFESI BIT(0)
/* Common FIFO bits */
/* RSCFDnCFDCFCCk */
#define RCANFD_CFCC_CFTML(gpriv, cftml) \
({\
typeof(gpriv) (_gpriv) = (gpriv); \
(((cftml) & (_gpriv)->info->max_cftml) << (_gpriv)->info->sh->cftml); \
})
#define RCANFD_CFCC_CFM(gpriv, x) (((x) & 0x3) << (gpriv)->info->sh->cfm)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_CFCC_CFIM BIT(12)
#define RCANFD_CFCC_CFDC(gpriv, x) (((x) & 0x7) << (gpriv)->info->sh->cfdc)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_CFCC_CFPLS(x) (((x) & 0x7) << 4)
#define RCANFD_CFCC_CFTXIE BIT(2)
#define RCANFD_CFCC_CFE BIT(0)
/* RSCFDnCFDCFSTSk */
#define RCANFD_CFSTS_CFMC(x) (((x) >> 8) & 0xff)
#define RCANFD_CFSTS_CFTXIF BIT(4)
#define RCANFD_CFSTS_CFMLT BIT(2)
#define RCANFD_CFSTS_CFFLL BIT(1)
#define RCANFD_CFSTS_CFEMP BIT(0)
/* RSCFDnCFDCFIDk */
#define RCANFD_CFID_CFIDE BIT(31)
#define RCANFD_CFID_CFRTR BIT(30)
/* RSCFDnCFDCFPTRk */
#define RCANFD_CFPTR_CFDLC(x) (((x) & 0xf) << 28)
/* RSCFDnCFDCFFDCSTSk */
#define RCANFD_CFFDCSTS_CFFDF BIT(2)
#define RCANFD_CFFDCSTS_CFBRS BIT(1)
#define RCANFD_CFFDCSTS_CFESI BIT(0)
/* This controller supports either Classical CAN only mode or CAN FD only mode.
* These modes are supported in two separate set of register maps & names.
* However, some of the register offsets are common for both modes. Those
* offsets are listed below as Common registers.
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
*
* The CAN FD only mode specific registers & Classical CAN only mode specific
* registers are listed separately. Their register names starts with
* RCANFD_F_xxx & RCANFD_C_xxx respectively.
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
*/
/* Common registers */
/* RSCFDnCFDCmNCFG / RSCFDnCmCFG */
#define RCANFD_CCFG(m) (0x0000 + (0x10 * (m)))
/* RSCFDnCFDCmCTR / RSCFDnCmCTR */
#define RCANFD_CCTR(m) (0x0004 + (0x10 * (m)))
/* RSCFDnCFDCmSTS / RSCFDnCmSTS */
#define RCANFD_CSTS(m) (0x0008 + (0x10 * (m)))
/* RSCFDnCFDCmERFL / RSCFDnCmERFL */
#define RCANFD_CERFL(m) (0x000C + (0x10 * (m)))
/* RSCFDnCFDGCFG / RSCFDnGCFG */
#define RCANFD_GCFG (0x0084)
/* RSCFDnCFDGCTR / RSCFDnGCTR */
#define RCANFD_GCTR (0x0088)
/* RSCFDnCFDGCTS / RSCFDnGCTS */
#define RCANFD_GSTS (0x008c)
/* RSCFDnCFDGERFL / RSCFDnGERFL */
#define RCANFD_GERFL (0x0090)
/* RSCFDnCFDGTSC / RSCFDnGTSC */
#define RCANFD_GTSC (0x0094)
/* RSCFDnCFDGAFLECTR / RSCFDnGAFLECTR */
#define RCANFD_GAFLECTR (0x0098)
/* RSCFDnCFDGAFLCFG / RSCFDnGAFLCFG */
#define RCANFD_GAFLCFG(w) (0x009c + (0x04 * (w)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDRMNB / RSCFDnRMNB */
#define RCANFD_RMNB (0x00a4)
/* RSCFDnCFDRMND / RSCFDnRMND */
#define RCANFD_RMND(y) (0x00a8 + (0x04 * (y)))
/* RSCFDnCFDRFCCx / RSCFDnRFCCx */
#define RCANFD_RFCC(gpriv, x) ((gpriv)->info->regs->rfcc + (0x04 * (x)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDRFSTSx / RSCFDnRFSTSx */
#define RCANFD_RFSTS(gpriv, x) (RCANFD_RFCC(gpriv, x) + 0x20)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDRFPCTRx / RSCFDnRFPCTRx */
#define RCANFD_RFPCTR(gpriv, x) (RCANFD_RFCC(gpriv, x) + 0x40)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Common FIFO Control registers */
/* RSCFDnCFDCFCCx / RSCFDnCFCCx */
#define RCANFD_CFCC(gpriv, ch, idx) \
((gpriv)->info->regs->cfcc + (0x0c * (ch)) + (0x04 * (idx)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDCFSTSx / RSCFDnCFSTSx */
#define RCANFD_CFSTS(gpriv, ch, idx) \
((gpriv)->info->regs->cfsts + (0x0c * (ch)) + (0x04 * (idx)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDCFPCTRx / RSCFDnCFPCTRx */
#define RCANFD_CFPCTR(gpriv, ch, idx) \
((gpriv)->info->regs->cfpctr + (0x0c * (ch)) + (0x04 * (idx)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDGRMCFG */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GRMCFG (0x04fc)
/* RSCFDnCFDGAFLIDj / RSCFDnGAFLIDj */
#define RCANFD_GAFLID(offset, j) ((offset) + (0x10 * (j)))
/* RSCFDnCFDGAFLMj / RSCFDnGAFLMj */
#define RCANFD_GAFLM(offset, j) ((offset) + 0x04 + (0x10 * (j)))
/* RSCFDnCFDGAFLP0j / RSCFDnGAFLP0j */
#define RCANFD_GAFLP0(offset, j) ((offset) + 0x08 + (0x10 * (j)))
/* RSCFDnCFDGAFLP1j / RSCFDnGAFLP1j */
#define RCANFD_GAFLP1(offset, j) ((offset) + 0x0c + (0x10 * (j)))
/* Classical CAN only mode register map */
/* RSCFDnGAFLXXXj offset */
#define RCANFD_C_GAFL_OFFSET (0x0500)
/* RSCFDnRFXXx -> RCANFD_C_RFXX(x) */
#define RCANFD_C_RFOFFSET (0x0e00)
#define RCANFD_C_RFID(x) (RCANFD_C_RFOFFSET + (0x10 * (x)))
#define RCANFD_C_RFPTR(x) (RCANFD_C_RFOFFSET + 0x04 + (0x10 * (x)))
#define RCANFD_C_RFDF(x, df) \
(RCANFD_C_RFOFFSET + 0x08 + (0x10 * (x)) + (0x04 * (df)))
/* RSCFDnCFXXk -> RCANFD_C_CFXX(ch, k) */
#define RCANFD_C_CFOFFSET (0x0e80)
#define RCANFD_C_CFID(ch, idx) \
(RCANFD_C_CFOFFSET + (0x30 * (ch)) + (0x10 * (idx)))
#define RCANFD_C_CFPTR(ch, idx) \
(RCANFD_C_CFOFFSET + 0x04 + (0x30 * (ch)) + (0x10 * (idx)))
#define RCANFD_C_CFDF(ch, idx, df) \
(RCANFD_C_CFOFFSET + 0x08 + (0x30 * (ch)) + (0x10 * (idx)) + (0x04 * (df)))
/* R-Car Gen4 Classical and CAN FD mode specific register map */
#define RCANFD_GEN4_GAFL_OFFSET (0x1800)
/* CAN FD mode specific register map */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDCmXXX -> gpriv->fcbase[m].xxx */
struct rcar_canfd_f_c {
u32 dcfg;
u32 cfdcfg;
u32 cfdctr;
u32 cfdsts;
u32 cfdcrc;
u32 pad[3];
};
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDGAFLXXXj offset */
#define RCANFD_F_GAFL_OFFSET (0x1000)
/* RSCFDnCFDRFXXx -> RCANFD_F_RFXX(x) */
#define RCANFD_F_RFOFFSET(gpriv) ((gpriv)->info->regs->rfoffset)
#define RCANFD_F_RFID(gpriv, x) (RCANFD_F_RFOFFSET(gpriv) + (0x80 * (x)))
#define RCANFD_F_RFPTR(gpriv, x) (RCANFD_F_RFOFFSET(gpriv) + 0x04 + (0x80 * (x)))
#define RCANFD_F_RFFDSTS(gpriv, x) (RCANFD_F_RFOFFSET(gpriv) + 0x08 + (0x80 * (x)))
#define RCANFD_F_RFDF(gpriv, x, df) \
(RCANFD_F_RFOFFSET(gpriv) + 0x0c + (0x80 * (x)) + (0x04 * (df)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* RSCFDnCFDCFXXk -> RCANFD_F_CFXX(ch, k) */
#define RCANFD_F_CFOFFSET(gpriv) ((gpriv)->info->regs->cfoffset)
#define RCANFD_F_CFID(gpriv, ch, idx) \
(RCANFD_F_CFOFFSET(gpriv) + (0x180 * (ch)) + (0x80 * (idx)))
#define RCANFD_F_CFPTR(gpriv, ch, idx) \
(RCANFD_F_CFOFFSET(gpriv) + 0x04 + (0x180 * (ch)) + (0x80 * (idx)))
#define RCANFD_F_CFFDCSTS(gpriv, ch, idx) \
(RCANFD_F_CFOFFSET(gpriv) + 0x08 + (0x180 * (ch)) + (0x80 * (idx)))
#define RCANFD_F_CFDF(gpriv, ch, idx, df) \
(RCANFD_F_CFOFFSET(gpriv) + 0x0c + (0x180 * (ch)) + (0x80 * (idx)) + \
(0x04 * (df)))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Constants */
#define RCANFD_FIFO_DEPTH 8 /* Tx FIFO depth */
#define RCANFD_NAPI_WEIGHT 8 /* Rx poll quota */
#define RCANFD_NUM_CHANNELS 8 /* Eight channels max */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
#define RCANFD_GAFL_PAGENUM(entry) ((entry) / 16)
#define RCANFD_CHANNEL_NUMRULES 1 /* only one rule per channel */
/* Rx FIFO is a global resource of the controller. There are 8 such FIFOs
* available. Each channel gets a dedicated Rx FIFO (i.e.) the channel
* number is added to RFFIFO index.
*/
#define RCANFD_RFFIFO_IDX 0
/* Tx/Rx or Common FIFO is a per channel resource. Each channel has 3 Common
* FIFOs dedicated to them. Use the first (index 0) FIFO out of the 3 for Tx.
*/
#define RCANFD_CFFIFO_IDX 0
struct rcar_canfd_global;
struct rcar_canfd_regs {
u16 rfcc; /* RX FIFO Configuration/Control Register */
u16 cfcc; /* Common FIFO Configuration/Control Register */
u16 cfsts; /* Common FIFO Status Register */
u16 cfpctr; /* Common FIFO Pointer Control Register */
u16 coffset; /* Channel Data Bitrate Configuration Register */
u16 rfoffset; /* Receive FIFO buffer access ID register */
u16 cfoffset; /* Transmit/receive FIFO buffer access ID register */
};
struct rcar_canfd_shift_data {
u8 ntseg2; /* Nominal Bit Rate Time Segment 2 Control */
u8 ntseg1; /* Nominal Bit Rate Time Segment 1 Control */
u8 nsjw; /* Nominal Bit Rate Resynchronization Jump Width Control */
u8 dtseg2; /* Data Bit Rate Time Segment 2 Control */
u8 dtseg1; /* Data Bit Rate Time Segment 1 Control */
u8 cftml; /* Common FIFO TX Message Buffer Link */
u8 cfm; /* Common FIFO Mode */
u8 cfdc; /* Common FIFO Depth Configuration */
};
struct rcar_canfd_hw_info {
const struct can_bittiming_const *nom_bittiming;
const struct can_bittiming_const *data_bittiming;
const struct can_tdc_const *tdc_const;
const struct rcar_canfd_regs *regs;
const struct rcar_canfd_shift_data *sh;
u8 rnc_field_width;
u8 max_aflpn;
u8 max_cftml;
u8 max_channels;
u8 postdiv;
/* hardware features */
unsigned shared_global_irqs:1; /* Has shared global irqs */
unsigned multi_channel_irqs:1; /* Has multiple channel irqs */
unsigned ch_interface_mode:1; /* Has channel interface mode */
unsigned shared_can_regs:1; /* Has shared classical can registers */
unsigned external_clk:1; /* Has external clock */
};
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Channel priv data */
struct rcar_canfd_channel {
struct can_priv can; /* Must be the first member */
struct net_device *ndev;
struct rcar_canfd_global *gpriv; /* Controller reference */
void __iomem *base; /* Register base address */
struct phy *transceiver; /* Optional transceiver */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct napi_struct napi;
u32 tx_head; /* Incremented on xmit */
u32 tx_tail; /* Incremented on xmit done */
u32 channel; /* Channel number */
spinlock_t tx_lock; /* To protect tx path */
};
/* Global priv data */
struct rcar_canfd_global {
struct rcar_canfd_channel *ch[RCANFD_NUM_CHANNELS];
void __iomem *base; /* Register base address */
struct rcar_canfd_f_c __iomem *fcbase;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct platform_device *pdev; /* Respective platform device */
struct clk *clkp; /* Peripheral clock */
struct clk *can_clk; /* fCAN clock */
unsigned long channels_mask; /* Enabled channels mask */
bool extclk; /* CANFD or Ext clock */
bool fdmode; /* CAN FD or Classical CAN only mode */
struct reset_control *rstc1;
struct reset_control *rstc2;
const struct rcar_canfd_hw_info *info;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
};
/* CAN FD mode nominal rate constants */
static const struct can_bittiming_const rcar_canfd_gen3_nom_bittiming_const = {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
.name = RCANFD_DRV_NAME,
.tseg1_min = 2,
.tseg1_max = 128,
.tseg2_min = 2,
.tseg2_max = 32,
.sjw_max = 32,
.brp_min = 1,
.brp_max = 1024,
.brp_inc = 1,
};
static const struct can_bittiming_const rcar_canfd_gen4_nom_bittiming_const = {
.name = RCANFD_DRV_NAME,
.tseg1_min = 2,
.tseg1_max = 256,
.tseg2_min = 2,
.tseg2_max = 128,
.sjw_max = 128,
.brp_min = 1,
.brp_max = 1024,
.brp_inc = 1,
};
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* CAN FD mode data rate constants */
static const struct can_bittiming_const rcar_canfd_gen3_data_bittiming_const = {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
.name = RCANFD_DRV_NAME,
.tseg1_min = 2,
.tseg1_max = 16,
.tseg2_min = 2,
.tseg2_max = 8,
.sjw_max = 8,
.brp_min = 1,
.brp_max = 256,
.brp_inc = 1,
};
static const struct can_bittiming_const rcar_canfd_gen4_data_bittiming_const = {
.name = RCANFD_DRV_NAME,
.tseg1_min = 2,
.tseg1_max = 32,
.tseg2_min = 2,
.tseg2_max = 16,
.sjw_max = 16,
.brp_min = 1,
.brp_max = 256,
.brp_inc = 1,
};
/* Classical CAN mode bitrate constants */
static const struct can_bittiming_const rcar_canfd_bittiming_const = {
.name = RCANFD_DRV_NAME,
.tseg1_min = 4,
.tseg1_max = 16,
.tseg2_min = 2,
.tseg2_max = 8,
.sjw_max = 4,
.brp_min = 1,
.brp_max = 1024,
.brp_inc = 1,
};
/* CAN FD Transmission Delay Compensation constants */
static const struct can_tdc_const rcar_canfd_gen3_tdc_const = {
.tdcv_min = 1,
.tdcv_max = 128,
.tdco_min = 1,
.tdco_max = 128,
.tdcf_min = 0, /* Filter window not supported */
.tdcf_max = 0,
};
static const struct can_tdc_const rcar_canfd_gen4_tdc_const = {
.tdcv_min = 1,
.tdcv_max = 256,
.tdco_min = 1,
.tdco_max = 256,
.tdcf_min = 0, /* Filter window not supported */
.tdcf_max = 0,
};
static const struct rcar_canfd_regs rcar_gen3_regs = {
.rfcc = 0x00b8,
.cfcc = 0x0118,
.cfsts = 0x0178,
.cfpctr = 0x01d8,
.coffset = 0x0500,
.rfoffset = 0x3000,
.cfoffset = 0x3400,
};
static const struct rcar_canfd_regs rcar_gen4_regs = {
.rfcc = 0x00c0,
.cfcc = 0x0120,
.cfsts = 0x01e0,
.cfpctr = 0x0240,
.coffset = 0x1400,
.rfoffset = 0x6000,
.cfoffset = 0x6400,
};
static const struct rcar_canfd_shift_data rcar_gen3_shift_data = {
.ntseg2 = 24,
.ntseg1 = 16,
.nsjw = 11,
.dtseg2 = 20,
.dtseg1 = 16,
.cftml = 20,
.cfm = 16,
.cfdc = 8,
};
static const struct rcar_canfd_shift_data rcar_gen4_shift_data = {
.ntseg2 = 25,
.ntseg1 = 17,
.nsjw = 10,
.dtseg2 = 16,
.dtseg1 = 8,
.cftml = 16,
.cfm = 8,
.cfdc = 21,
};
static const struct rcar_canfd_hw_info rcar_gen3_hw_info = {
.nom_bittiming = &rcar_canfd_gen3_nom_bittiming_const,
.data_bittiming = &rcar_canfd_gen3_data_bittiming_const,
.tdc_const = &rcar_canfd_gen3_tdc_const,
.regs = &rcar_gen3_regs,
.sh = &rcar_gen3_shift_data,
.rnc_field_width = 8,
.max_aflpn = 31,
.max_cftml = 15,
.max_channels = 2,
.postdiv = 2,
.shared_global_irqs = 1,
.ch_interface_mode = 0,
.shared_can_regs = 0,
.external_clk = 1,
};
static const struct rcar_canfd_hw_info rcar_gen4_hw_info = {
.nom_bittiming = &rcar_canfd_gen4_nom_bittiming_const,
.data_bittiming = &rcar_canfd_gen4_data_bittiming_const,
.tdc_const = &rcar_canfd_gen4_tdc_const,
.regs = &rcar_gen4_regs,
.sh = &rcar_gen4_shift_data,
.rnc_field_width = 16,
.max_aflpn = 127,
.max_cftml = 31,
.max_channels = 8,
.postdiv = 2,
.shared_global_irqs = 1,
.ch_interface_mode = 1,
.shared_can_regs = 1,
.external_clk = 1,
};
static const struct rcar_canfd_hw_info rzg2l_hw_info = {
.nom_bittiming = &rcar_canfd_gen3_nom_bittiming_const,
.data_bittiming = &rcar_canfd_gen3_data_bittiming_const,
.tdc_const = &rcar_canfd_gen3_tdc_const,
.regs = &rcar_gen3_regs,
.sh = &rcar_gen3_shift_data,
.rnc_field_width = 8,
.max_aflpn = 31,
.max_cftml = 15,
.max_channels = 2,
.postdiv = 1,
.multi_channel_irqs = 1,
.ch_interface_mode = 0,
.shared_can_regs = 0,
.external_clk = 1,
};
static const struct rcar_canfd_hw_info r9a09g047_hw_info = {
.nom_bittiming = &rcar_canfd_gen4_nom_bittiming_const,
.data_bittiming = &rcar_canfd_gen4_data_bittiming_const,
.tdc_const = &rcar_canfd_gen4_tdc_const,
.regs = &rcar_gen4_regs,
.sh = &rcar_gen4_shift_data,
.rnc_field_width = 16,
.max_aflpn = 63,
.max_cftml = 31,
.max_channels = 6,
.postdiv = 1,
.multi_channel_irqs = 1,
.ch_interface_mode = 1,
.shared_can_regs = 1,
.external_clk = 0,
};
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Helper functions */
static inline void rcar_canfd_update(u32 mask, u32 val, u32 __iomem *reg)
{
u32 data = readl(reg);
data &= ~mask;
data |= (val & mask);
writel(data, reg);
}
static inline u32 rcar_canfd_read(void __iomem *base, u32 offset)
{
return readl(base + offset);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static inline void rcar_canfd_write(void __iomem *base, u32 offset, u32 val)
{
writel(val, base + offset);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_set_bit(void __iomem *base, u32 reg, u32 val)
{
rcar_canfd_update(val, val, base + reg);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_clear_bit(void __iomem *base, u32 reg, u32 val)
{
rcar_canfd_update(val, 0, base + reg);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_update_bit(void __iomem *base, u32 reg,
u32 mask, u32 val)
{
rcar_canfd_update(mask, val, base + reg);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_set_bit_reg(void __iomem *addr, u32 val)
{
rcar_canfd_update(val, val, addr);
}
static void rcar_canfd_update_bit_reg(void __iomem *addr, u32 mask, u32 val)
{
rcar_canfd_update(mask, val, addr);
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
static void rcar_canfd_get_data(struct rcar_canfd_channel *priv,
struct canfd_frame *cf, u32 off)
{
u32 *data = (u32 *)cf->data;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u32 i, lwords;
lwords = DIV_ROUND_UP(cf->len, sizeof(u32));
for (i = 0; i < lwords; i++)
data[i] = rcar_canfd_read(priv->base, off + i * sizeof(u32));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_put_data(struct rcar_canfd_channel *priv,
struct canfd_frame *cf, u32 off)
{
const u32 *data = (u32 *)cf->data;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u32 i, lwords;
lwords = DIV_ROUND_UP(cf->len, sizeof(u32));
for (i = 0; i < lwords; i++)
rcar_canfd_write(priv->base, off + i * sizeof(u32), data[i]);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_tx_failure_cleanup(struct net_device *ndev)
{
u32 i;
for (i = 0; i < RCANFD_FIFO_DEPTH; i++)
can_free_echo_skb(ndev, i, NULL);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_set_rnc(struct rcar_canfd_global *gpriv, unsigned int ch,
unsigned int num_rules)
{
unsigned int rnc_stride = 32 / gpriv->info->rnc_field_width;
unsigned int shift = 32 - (ch % rnc_stride + 1) * gpriv->info->rnc_field_width;
unsigned int w = ch / rnc_stride;
u32 rnc = num_rules << shift;
rcar_canfd_set_bit(gpriv->base, RCANFD_GAFLCFG(w), rnc);
}
static void rcar_canfd_set_mode(struct rcar_canfd_global *gpriv)
{
if (gpriv->info->ch_interface_mode) {
u32 ch, val = gpriv->fdmode ? RCANFD_GEN4_FDCFG_FDOE
: RCANFD_GEN4_FDCFG_CLOE;
for_each_set_bit(ch, &gpriv->channels_mask,
gpriv->info->max_channels)
rcar_canfd_set_bit_reg(&gpriv->fcbase[ch].cfdcfg, val);
} else {
if (gpriv->fdmode)
rcar_canfd_set_bit(gpriv->base, RCANFD_GRMCFG,
RCANFD_GRMCFG_RCMC);
else
rcar_canfd_clear_bit(gpriv->base, RCANFD_GRMCFG,
RCANFD_GRMCFG_RCMC);
}
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
static int rcar_canfd_reset_controller(struct rcar_canfd_global *gpriv)
{
struct device *dev = &gpriv->pdev->dev;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u32 sts, ch;
int err;
/* Check RAMINIT flag as CAN RAM initialization takes place
* after the MCU reset
*/
err = readl_poll_timeout((gpriv->base + RCANFD_GSTS), sts,
!(sts & RCANFD_GSTS_GRAMINIT), 2, 500000);
if (err) {
dev_dbg(dev, "global raminit failed\n");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return err;
}
/* Transition to Global Reset mode */
rcar_canfd_clear_bit(gpriv->base, RCANFD_GCTR, RCANFD_GCTR_GSLPR);
rcar_canfd_update_bit(gpriv->base, RCANFD_GCTR,
RCANFD_GCTR_GMDC_MASK, RCANFD_GCTR_GMDC_GRESET);
/* Ensure Global reset mode */
err = readl_poll_timeout((gpriv->base + RCANFD_GSTS), sts,
(sts & RCANFD_GSTS_GRSTSTS), 2, 500000);
if (err) {
dev_dbg(dev, "global reset failed\n");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return err;
}
/* Reset Global error flags */
rcar_canfd_write(gpriv->base, RCANFD_GERFL, 0x0);
/* Set the controller into appropriate mode */
rcar_canfd_set_mode(gpriv);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Transition all Channels to reset mode */
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels) {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_clear_bit(gpriv->base,
RCANFD_CCTR(ch), RCANFD_CCTR_CSLPR);
rcar_canfd_update_bit(gpriv->base, RCANFD_CCTR(ch),
RCANFD_CCTR_CHMDC_MASK,
RCANFD_CCTR_CHDMC_CRESET);
/* Ensure Channel reset mode */
err = readl_poll_timeout((gpriv->base + RCANFD_CSTS(ch)), sts,
(sts & RCANFD_CSTS_CRSTSTS),
2, 500000);
if (err) {
dev_dbg(dev, "channel %u reset failed\n", ch);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return err;
}
}
return 0;
}
static void rcar_canfd_configure_controller(struct rcar_canfd_global *gpriv)
{
u32 cfg, ch;
/* Global configuration settings */
/* ECC Error flag Enable */
cfg = RCANFD_GCFG_EEFE;
if (gpriv->fdmode)
/* Truncate payload to configured message size RFPLS */
cfg |= RCANFD_GCFG_CMPOC;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Set External Clock if selected */
if (gpriv->extclk)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
cfg |= RCANFD_GCFG_DCS;
rcar_canfd_set_bit(gpriv->base, RCANFD_GCFG, cfg);
/* Channel configuration settings */
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels) {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_set_bit(gpriv->base, RCANFD_CCTR(ch),
RCANFD_CCTR_ERRD);
rcar_canfd_update_bit(gpriv->base, RCANFD_CCTR(ch),
RCANFD_CCTR_BOM_MASK,
RCANFD_CCTR_BOM_BENTRY);
}
}
static void rcar_canfd_configure_afl_rules(struct rcar_canfd_global *gpriv,
u32 ch, u32 rule_entry)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{
unsigned int offset, page, num_rules = RCANFD_CHANNEL_NUMRULES;
u32 rule_entry_index = rule_entry % 16;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u32 ridx = ch + RCANFD_RFFIFO_IDX;
/* Enable write access to entry */
page = RCANFD_GAFL_PAGENUM(rule_entry);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_set_bit(gpriv->base, RCANFD_GAFLECTR,
(RCANFD_GAFLECTR_AFLPN(gpriv, page) |
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
RCANFD_GAFLECTR_AFLDAE));
/* Write number of rules for channel */
rcar_canfd_set_rnc(gpriv, ch, num_rules);
if (gpriv->info->shared_can_regs)
offset = RCANFD_GEN4_GAFL_OFFSET;
else if (gpriv->fdmode)
offset = RCANFD_F_GAFL_OFFSET;
else
offset = RCANFD_C_GAFL_OFFSET;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Accept all IDs */
rcar_canfd_write(gpriv->base, RCANFD_GAFLID(offset, rule_entry_index), 0);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* IDE or RTR is not considered for matching */
rcar_canfd_write(gpriv->base, RCANFD_GAFLM(offset, rule_entry_index), 0);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Any data length accepted */
rcar_canfd_write(gpriv->base, RCANFD_GAFLP0(offset, rule_entry_index), 0);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Place the msg in corresponding Rx FIFO entry */
rcar_canfd_set_bit(gpriv->base, RCANFD_GAFLP1(offset, rule_entry_index),
RCANFD_GAFLP1_GAFLFDP(ridx));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Disable write access to page */
rcar_canfd_clear_bit(gpriv->base,
RCANFD_GAFLECTR, RCANFD_GAFLECTR_AFLDAE);
}
static void rcar_canfd_configure_rx(struct rcar_canfd_global *gpriv, u32 ch)
{
/* Rx FIFO is used for reception */
u32 cfg;
u16 rfdc, rfpls;
/* Select Rx FIFO based on channel */
u32 ridx = ch + RCANFD_RFFIFO_IDX;
rfdc = 2; /* b010 - 8 messages Rx FIFO depth */
if (gpriv->fdmode)
rfpls = 7; /* b111 - Max 64 bytes payload */
else
rfpls = 0; /* b000 - Max 8 bytes payload */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
cfg = (RCANFD_RFCC_RFIM | RCANFD_RFCC_RFDC(rfdc) |
RCANFD_RFCC_RFPLS(rfpls) | RCANFD_RFCC_RFIE);
rcar_canfd_write(gpriv->base, RCANFD_RFCC(gpriv, ridx), cfg);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_configure_tx(struct rcar_canfd_global *gpriv, u32 ch)
{
/* Tx/Rx(Common) FIFO configured in Tx mode is
* used for transmission
*
* Each channel has 3 Common FIFO dedicated to them.
* Use the 1st (index 0) out of 3
*/
u32 cfg;
u16 cftml, cfm, cfdc, cfpls;
cftml = 0; /* 0th buffer */
cfm = 1; /* b01 - Transmit mode */
cfdc = 2; /* b010 - 8 messages Tx FIFO depth */
if (gpriv->fdmode)
cfpls = 7; /* b111 - Max 64 bytes payload */
else
cfpls = 0; /* b000 - Max 8 bytes payload */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
cfg = (RCANFD_CFCC_CFTML(gpriv, cftml) | RCANFD_CFCC_CFM(gpriv, cfm) |
RCANFD_CFCC_CFIM | RCANFD_CFCC_CFDC(gpriv, cfdc) |
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
RCANFD_CFCC_CFPLS(cfpls) | RCANFD_CFCC_CFTXIE);
rcar_canfd_write(gpriv->base, RCANFD_CFCC(gpriv, ch, RCANFD_CFFIFO_IDX), cfg);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (gpriv->fdmode)
/* Clear FD mode specific control/status register */
rcar_canfd_write(gpriv->base,
RCANFD_F_CFFDCSTS(gpriv, ch, RCANFD_CFFIFO_IDX), 0);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static void rcar_canfd_enable_global_interrupts(struct rcar_canfd_global *gpriv)
{
u32 ctr;
/* Clear any stray error interrupt flags */
rcar_canfd_write(gpriv->base, RCANFD_GERFL, 0);
/* Global interrupts setup */
ctr = RCANFD_GCTR_MEIE;
if (gpriv->fdmode)
ctr |= RCANFD_GCTR_CFMPOFIE;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_set_bit(gpriv->base, RCANFD_GCTR, ctr);
}
static void rcar_canfd_disable_global_interrupts(struct rcar_canfd_global
*gpriv)
{
/* Disable all interrupts */
rcar_canfd_write(gpriv->base, RCANFD_GCTR, 0);
/* Clear any stray error interrupt flags */
rcar_canfd_write(gpriv->base, RCANFD_GERFL, 0);
}
static void rcar_canfd_enable_channel_interrupts(struct rcar_canfd_channel
*priv)
{
u32 ctr, ch = priv->channel;
/* Clear any stray error flags */
rcar_canfd_write(priv->base, RCANFD_CERFL(ch), 0);
/* Channel interrupts setup */
ctr = (RCANFD_CCTR_TAIE |
RCANFD_CCTR_ALIE | RCANFD_CCTR_BLIE |
RCANFD_CCTR_OLIE | RCANFD_CCTR_BORIE |
RCANFD_CCTR_BOEIE | RCANFD_CCTR_EPIE |
RCANFD_CCTR_EWIE | RCANFD_CCTR_BEIE);
rcar_canfd_set_bit(priv->base, RCANFD_CCTR(ch), ctr);
}
static void rcar_canfd_disable_channel_interrupts(struct rcar_canfd_channel
*priv)
{
u32 ctr, ch = priv->channel;
ctr = (RCANFD_CCTR_TAIE |
RCANFD_CCTR_ALIE | RCANFD_CCTR_BLIE |
RCANFD_CCTR_OLIE | RCANFD_CCTR_BORIE |
RCANFD_CCTR_BOEIE | RCANFD_CCTR_EPIE |
RCANFD_CCTR_EWIE | RCANFD_CCTR_BEIE);
rcar_canfd_clear_bit(priv->base, RCANFD_CCTR(ch), ctr);
/* Clear any stray error flags */
rcar_canfd_write(priv->base, RCANFD_CERFL(ch), 0);
}
static void rcar_canfd_global_error(struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct net_device_stats *stats = &ndev->stats;
u32 ch = priv->channel;
u32 gerfl, sts;
u32 ridx = ch + RCANFD_RFFIFO_IDX;
gerfl = rcar_canfd_read(priv->base, RCANFD_GERFL);
if (gerfl & FIELD_PREP(RCANFD_GERFL_EEF, BIT(ch))) {
netdev_dbg(ndev, "Ch%u: ECC Error flag\n", ch);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
stats->tx_dropped++;
}
if (gerfl & RCANFD_GERFL_MES) {
sts = rcar_canfd_read(priv->base,
RCANFD_CFSTS(gpriv, ch, RCANFD_CFFIFO_IDX));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (sts & RCANFD_CFSTS_CFMLT) {
netdev_dbg(ndev, "Tx Message Lost flag\n");
stats->tx_dropped++;
rcar_canfd_write(priv->base,
RCANFD_CFSTS(gpriv, ch, RCANFD_CFFIFO_IDX),
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
sts & ~RCANFD_CFSTS_CFMLT);
}
sts = rcar_canfd_read(priv->base, RCANFD_RFSTS(gpriv, ridx));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (sts & RCANFD_RFSTS_RFMLT) {
netdev_dbg(ndev, "Rx Message Lost flag\n");
stats->rx_dropped++;
rcar_canfd_write(priv->base, RCANFD_RFSTS(gpriv, ridx),
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
sts & ~RCANFD_RFSTS_RFMLT);
}
}
if (gpriv->fdmode && gerfl & RCANFD_GERFL_CMPOF) {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Message Lost flag will be set for respective channel
* when this condition happens with counters and flags
* already updated.
*/
netdev_dbg(ndev, "global payload overflow interrupt\n");
}
/* Clear all global error interrupts. Only affected channels bits
* get cleared
*/
rcar_canfd_write(priv->base, RCANFD_GERFL, 0);
}
static void rcar_canfd_error(struct net_device *ndev, u32 cerfl,
u16 txerr, u16 rxerr)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct net_device_stats *stats = &ndev->stats;
struct can_frame *cf;
struct sk_buff *skb;
u32 ch = priv->channel;
netdev_dbg(ndev, "ch erfl %x txerr %u rxerr %u\n", cerfl, txerr, rxerr);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Propagate the error condition to the CAN stack */
skb = alloc_can_err_skb(ndev, &cf);
if (!skb) {
stats->rx_dropped++;
return;
}
/* Channel error interrupts */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (cerfl & RCANFD_CERFL_BEF) {
netdev_dbg(ndev, "Bus error\n");
cf->can_id |= CAN_ERR_BUSERROR | CAN_ERR_PROT;
cf->data[2] = CAN_ERR_PROT_UNSPEC;
priv->can.can_stats.bus_error++;
}
if (cerfl & RCANFD_CERFL_ADERR) {
netdev_dbg(ndev, "ACK Delimiter Error\n");
stats->tx_errors++;
cf->data[3] |= CAN_ERR_PROT_LOC_ACK_DEL;
}
if (cerfl & RCANFD_CERFL_B0ERR) {
netdev_dbg(ndev, "Bit Error (dominant)\n");
stats->tx_errors++;
cf->data[2] |= CAN_ERR_PROT_BIT0;
}
if (cerfl & RCANFD_CERFL_B1ERR) {
netdev_dbg(ndev, "Bit Error (recessive)\n");
stats->tx_errors++;
cf->data[2] |= CAN_ERR_PROT_BIT1;
}
if (cerfl & RCANFD_CERFL_CERR) {
netdev_dbg(ndev, "CRC Error\n");
stats->rx_errors++;
cf->data[3] |= CAN_ERR_PROT_LOC_CRC_SEQ;
}
if (cerfl & RCANFD_CERFL_AERR) {
netdev_dbg(ndev, "ACK Error\n");
stats->tx_errors++;
cf->can_id |= CAN_ERR_ACK;
cf->data[3] |= CAN_ERR_PROT_LOC_ACK;
}
if (cerfl & RCANFD_CERFL_FERR) {
netdev_dbg(ndev, "Form Error\n");
stats->rx_errors++;
cf->data[2] |= CAN_ERR_PROT_FORM;
}
if (cerfl & RCANFD_CERFL_SERR) {
netdev_dbg(ndev, "Stuff Error\n");
stats->rx_errors++;
cf->data[2] |= CAN_ERR_PROT_STUFF;
}
if (cerfl & RCANFD_CERFL_ALF) {
netdev_dbg(ndev, "Arbitration lost Error\n");
priv->can.can_stats.arbitration_lost++;
cf->can_id |= CAN_ERR_LOSTARB;
cf->data[0] |= CAN_ERR_LOSTARB_UNSPEC;
}
if (cerfl & RCANFD_CERFL_BLF) {
netdev_dbg(ndev, "Bus Lock Error\n");
stats->rx_errors++;
cf->can_id |= CAN_ERR_BUSERROR;
}
if (cerfl & RCANFD_CERFL_EWF) {
netdev_dbg(ndev, "Error warning interrupt\n");
priv->can.state = CAN_STATE_ERROR_WARNING;
priv->can.can_stats.error_warning++;
cf->can_id |= CAN_ERR_CRTL | CAN_ERR_CNT;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
cf->data[1] = txerr > rxerr ? CAN_ERR_CRTL_TX_WARNING :
CAN_ERR_CRTL_RX_WARNING;
cf->data[6] = txerr;
cf->data[7] = rxerr;
}
if (cerfl & RCANFD_CERFL_EPF) {
netdev_dbg(ndev, "Error passive interrupt\n");
priv->can.state = CAN_STATE_ERROR_PASSIVE;
priv->can.can_stats.error_passive++;
cf->can_id |= CAN_ERR_CRTL | CAN_ERR_CNT;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
cf->data[1] = txerr > rxerr ? CAN_ERR_CRTL_TX_PASSIVE :
CAN_ERR_CRTL_RX_PASSIVE;
cf->data[6] = txerr;
cf->data[7] = rxerr;
}
if (cerfl & RCANFD_CERFL_BOEF) {
netdev_dbg(ndev, "Bus-off entry interrupt\n");
rcar_canfd_tx_failure_cleanup(ndev);
priv->can.state = CAN_STATE_BUS_OFF;
priv->can.can_stats.bus_off++;
can_bus_off(ndev);
cf->can_id |= CAN_ERR_BUSOFF;
}
if (cerfl & RCANFD_CERFL_OVLF) {
netdev_dbg(ndev,
"Overload Frame Transmission error interrupt\n");
stats->tx_errors++;
cf->can_id |= CAN_ERR_PROT;
cf->data[2] |= CAN_ERR_PROT_OVERLOAD;
}
/* Clear channel error interrupts that are handled */
rcar_canfd_write(priv->base, RCANFD_CERFL(ch),
RCANFD_CERFL_ERR(~cerfl));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
netif_rx(skb);
}
static void rcar_canfd_tx_done(struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct net_device_stats *stats = &ndev->stats;
u32 sts;
unsigned long flags;
u32 ch = priv->channel;
do {
u8 unsent, sent;
sent = priv->tx_tail % RCANFD_FIFO_DEPTH;
stats->tx_packets++;
can: do not increase tx_bytes statistics for RTR frames The actual payload length of the CAN Remote Transmission Request (RTR) frames is always 0, i.e. no payload is transmitted on the wire. However, those RTR frames still use the DLC to indicate the length of the requested frame. As such, net_device_stats::tx_bytes should not be increased when sending RTR frames. The function can_get_echo_skb() already returns the correct length, even for RTR frames (c.f. [1]). However, for historical reasons, the drivers do not use can_get_echo_skb()'s return value and instead, most of them store a temporary length (or dlc) in some local structure or array. Using the return value of can_get_echo_skb() solves the issue. After doing this, such length/dlc fields become unused and so this patch does the adequate cleaning when needed. This patch fixes all the CAN drivers. Finally, can_get_echo_skb() is decorated with the __must_check attribute in order to force future drivers to correctly use its return value (else the compiler would emit a warning). [1] commit ed3320cec279 ("can: dev: __can_get_echo_skb(): fix real payload length return value for RTR frames") Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: Yasushi SHOJI <yashi@spacecubics.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Stephane Grosjean <s.grosjean@peak-system.com> Cc: Andreas Larsson <andreas@gaisler.com> Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 [mkl: add conversion for grcan] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-12-07 21:15:31 +09:00
stats->tx_bytes += can_get_echo_skb(ndev, sent, NULL);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
spin_lock_irqsave(&priv->tx_lock, flags);
priv->tx_tail++;
sts = rcar_canfd_read(priv->base,
RCANFD_CFSTS(gpriv, ch, RCANFD_CFFIFO_IDX));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
unsent = RCANFD_CFSTS_CFMC(sts);
/* Wake producer only when there is room */
if (unsent != RCANFD_FIFO_DEPTH)
netif_wake_queue(ndev);
if (priv->tx_head - priv->tx_tail <= unsent) {
spin_unlock_irqrestore(&priv->tx_lock, flags);
break;
}
spin_unlock_irqrestore(&priv->tx_lock, flags);
} while (1);
/* Clear interrupt */
rcar_canfd_write(priv->base, RCANFD_CFSTS(gpriv, ch, RCANFD_CFFIFO_IDX),
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
sts & ~RCANFD_CFSTS_CFTXIF);
}
static void rcar_canfd_handle_global_err(struct rcar_canfd_global *gpriv, u32 ch)
{
struct rcar_canfd_channel *priv = gpriv->ch[ch];
struct net_device *ndev = priv->ndev;
u32 gerfl;
/* Handle global error interrupts */
gerfl = rcar_canfd_read(priv->base, RCANFD_GERFL);
if (unlikely(RCANFD_GERFL_ERR(gpriv, gerfl)))
rcar_canfd_global_error(ndev);
}
static irqreturn_t rcar_canfd_global_err_interrupt(int irq, void *dev_id)
{
struct rcar_canfd_global *gpriv = dev_id;
u32 ch;
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels)
rcar_canfd_handle_global_err(gpriv, ch);
return IRQ_HANDLED;
}
static void rcar_canfd_handle_global_receive(struct rcar_canfd_global *gpriv, u32 ch)
{
struct rcar_canfd_channel *priv = gpriv->ch[ch];
u32 ridx = ch + RCANFD_RFFIFO_IDX;
u32 sts, cc;
/* Handle Rx interrupts */
sts = rcar_canfd_read(priv->base, RCANFD_RFSTS(gpriv, ridx));
cc = rcar_canfd_read(priv->base, RCANFD_RFCC(gpriv, ridx));
if (likely(sts & RCANFD_RFSTS_RFIF &&
cc & RCANFD_RFCC_RFIE)) {
if (napi_schedule_prep(&priv->napi)) {
/* Disable Rx FIFO interrupts */
rcar_canfd_clear_bit(priv->base,
RCANFD_RFCC(gpriv, ridx),
RCANFD_RFCC_RFIE);
__napi_schedule(&priv->napi);
}
}
}
static irqreturn_t rcar_canfd_global_receive_fifo_interrupt(int irq, void *dev_id)
{
struct rcar_canfd_global *gpriv = dev_id;
u32 ch;
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels)
rcar_canfd_handle_global_receive(gpriv, ch);
return IRQ_HANDLED;
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
static irqreturn_t rcar_canfd_global_interrupt(int irq, void *dev_id)
{
struct rcar_canfd_global *gpriv = dev_id;
u32 ch;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Global error interrupts still indicate a condition specific
* to a channel. RxFIFO interrupt is a global interrupt.
*/
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels) {
rcar_canfd_handle_global_err(gpriv, ch);
rcar_canfd_handle_global_receive(gpriv, ch);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
return IRQ_HANDLED;
}
static void rcar_canfd_state_change(struct net_device *ndev,
u16 txerr, u16 rxerr)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct net_device_stats *stats = &ndev->stats;
enum can_state rx_state, tx_state, state = priv->can.state;
struct can_frame *cf;
struct sk_buff *skb;
/* Handle transition from error to normal states */
if (txerr < 96 && rxerr < 96)
state = CAN_STATE_ERROR_ACTIVE;
else if (txerr < 128 && rxerr < 128)
state = CAN_STATE_ERROR_WARNING;
if (state != priv->can.state) {
netdev_dbg(ndev, "state: new %d, old %d: txerr %u, rxerr %u\n",
state, priv->can.state, txerr, rxerr);
skb = alloc_can_err_skb(ndev, &cf);
if (!skb) {
stats->rx_dropped++;
return;
}
tx_state = txerr >= rxerr ? state : 0;
rx_state = txerr <= rxerr ? state : 0;
can_change_state(ndev, cf, tx_state, rx_state);
netif_rx(skb);
}
}
static void rcar_canfd_handle_channel_tx(struct rcar_canfd_global *gpriv, u32 ch)
{
struct rcar_canfd_channel *priv = gpriv->ch[ch];
struct net_device *ndev = priv->ndev;
u32 sts;
/* Handle Tx interrupts */
sts = rcar_canfd_read(priv->base,
RCANFD_CFSTS(gpriv, ch, RCANFD_CFFIFO_IDX));
if (likely(sts & RCANFD_CFSTS_CFTXIF))
rcar_canfd_tx_done(ndev);
}
static irqreturn_t rcar_canfd_channel_tx_interrupt(int irq, void *dev_id)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{
struct rcar_canfd_channel *priv = dev_id;
rcar_canfd_handle_channel_tx(priv->gpriv, priv->channel);
return IRQ_HANDLED;
}
static void rcar_canfd_handle_channel_err(struct rcar_canfd_global *gpriv, u32 ch)
{
struct rcar_canfd_channel *priv = gpriv->ch[ch];
struct net_device *ndev = priv->ndev;
u16 txerr, rxerr;
u32 sts, cerfl;
/* Handle channel error interrupts */
cerfl = rcar_canfd_read(priv->base, RCANFD_CERFL(ch));
sts = rcar_canfd_read(priv->base, RCANFD_CSTS(ch));
txerr = RCANFD_CSTS_TECCNT(sts);
rxerr = RCANFD_CSTS_RECCNT(sts);
if (unlikely(RCANFD_CERFL_ERR(cerfl)))
rcar_canfd_error(ndev, cerfl, txerr, rxerr);
/* Handle state change to lower states */
if (unlikely(priv->can.state != CAN_STATE_ERROR_ACTIVE &&
priv->can.state != CAN_STATE_BUS_OFF))
rcar_canfd_state_change(ndev, txerr, rxerr);
}
static irqreturn_t rcar_canfd_channel_err_interrupt(int irq, void *dev_id)
{
struct rcar_canfd_channel *priv = dev_id;
rcar_canfd_handle_channel_err(priv->gpriv, priv->channel);
return IRQ_HANDLED;
}
static irqreturn_t rcar_canfd_channel_interrupt(int irq, void *dev_id)
{
struct rcar_canfd_global *gpriv = dev_id;
u32 ch;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Common FIFO is a per channel resource */
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels) {
rcar_canfd_handle_channel_err(gpriv, ch);
rcar_canfd_handle_channel_tx(gpriv, ch);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return IRQ_HANDLED;
}
static void rcar_canfd_set_bittiming(struct net_device *ndev)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{
u32 mask = RCANFD_FDCFG_TDCO | RCANFD_FDCFG_TDCE | RCANFD_FDCFG_TDCOC;
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
const struct can_bittiming *bt = &priv->can.bittiming;
const struct can_bittiming *dbt = &priv->can.fd.data_bittiming;
const struct can_tdc_const *tdc_const = priv->can.fd.tdc_const;
const struct can_tdc *tdc = &priv->can.fd.tdc;
u32 cfg, tdcmode = 0, tdco = 0;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u16 brp, sjw, tseg1, tseg2;
u32 ch = priv->channel;
/* Nominal bit timing settings */
brp = bt->brp - 1;
sjw = bt->sjw - 1;
tseg1 = bt->prop_seg + bt->phase_seg1 - 1;
tseg2 = bt->phase_seg2 - 1;
if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) || gpriv->info->shared_can_regs) {
cfg = (RCANFD_NCFG_NTSEG1(gpriv, tseg1) | RCANFD_NCFG_NBRP(brp) |
RCANFD_NCFG_NSJW(gpriv, sjw) | RCANFD_NCFG_NTSEG2(gpriv, tseg2));
} else {
cfg = (RCANFD_CFG_TSEG1(tseg1) | RCANFD_CFG_BRP(brp) |
RCANFD_CFG_SJW(sjw) | RCANFD_CFG_TSEG2(tseg2));
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_write(priv->base, RCANFD_CCFG(ch), cfg);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (!(priv->can.ctrlmode & CAN_CTRLMODE_FD))
return;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Data bit timing settings */
brp = dbt->brp - 1;
sjw = dbt->sjw - 1;
tseg1 = dbt->prop_seg + dbt->phase_seg1 - 1;
tseg2 = dbt->phase_seg2 - 1;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
cfg = (RCANFD_DCFG_DTSEG1(gpriv, tseg1) | RCANFD_DCFG_DBRP(brp) |
RCANFD_DCFG_DSJW(gpriv, sjw) | RCANFD_DCFG_DTSEG2(gpriv, tseg2));
writel(cfg, &gpriv->fcbase[ch].dcfg);
/* Transceiver Delay Compensation */
if (priv->can.ctrlmode & CAN_CTRLMODE_TDC_AUTO) {
/* TDC enabled, measured + offset */
tdcmode = RCANFD_FDCFG_TDCE;
tdco = tdc->tdco - 1;
} else if (priv->can.ctrlmode & CAN_CTRLMODE_TDC_MANUAL) {
/* TDC enabled, offset only */
tdcmode = RCANFD_FDCFG_TDCE | RCANFD_FDCFG_TDCOC;
tdco = min(tdc->tdcv + tdc->tdco, tdc_const->tdco_max) - 1;
}
rcar_canfd_update_bit_reg(&gpriv->fcbase[ch].cfdcfg, mask,
tdcmode | FIELD_PREP(RCANFD_FDCFG_TDCO, tdco));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static int rcar_canfd_start(struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
int err = -EOPNOTSUPP;
u32 sts, ch = priv->channel;
u32 ridx = ch + RCANFD_RFFIFO_IDX;
rcar_canfd_set_bittiming(ndev);
rcar_canfd_enable_channel_interrupts(priv);
/* Set channel to Operational mode */
rcar_canfd_update_bit(priv->base, RCANFD_CCTR(ch),
RCANFD_CCTR_CHMDC_MASK, RCANFD_CCTR_CHDMC_COPM);
/* Verify channel mode change */
err = readl_poll_timeout((priv->base + RCANFD_CSTS(ch)), sts,
(sts & RCANFD_CSTS_COMSTS), 2, 500000);
if (err) {
netdev_err(ndev, "channel %u communication state failed\n", ch);
goto fail_mode_change;
}
/* Enable Common & Rx FIFO */
rcar_canfd_set_bit(priv->base, RCANFD_CFCC(gpriv, ch, RCANFD_CFFIFO_IDX),
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
RCANFD_CFCC_CFE);
rcar_canfd_set_bit(priv->base, RCANFD_RFCC(gpriv, ridx), RCANFD_RFCC_RFE);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
priv->can.state = CAN_STATE_ERROR_ACTIVE;
return 0;
fail_mode_change:
rcar_canfd_disable_channel_interrupts(priv);
return err;
}
static int rcar_canfd_open(struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
int err;
err = phy_power_on(priv->transceiver);
if (err) {
netdev_err(ndev, "failed to power on PHY: %pe\n", ERR_PTR(err));
return err;
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Peripheral clock is already enabled in probe */
err = clk_prepare_enable(gpriv->can_clk);
if (err) {
netdev_err(ndev, "failed to enable CAN clock: %pe\n", ERR_PTR(err));
goto out_phy;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
err = open_candev(ndev);
if (err) {
netdev_err(ndev, "open_candev() failed: %pe\n", ERR_PTR(err));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
goto out_can_clock;
}
napi_enable(&priv->napi);
err = rcar_canfd_start(ndev);
if (err)
goto out_close;
netif_start_queue(ndev);
return 0;
out_close:
napi_disable(&priv->napi);
close_candev(ndev);
out_can_clock:
clk_disable_unprepare(gpriv->can_clk);
out_phy:
phy_power_off(priv->transceiver);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return err;
}
static void rcar_canfd_stop(struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
int err;
u32 sts, ch = priv->channel;
u32 ridx = ch + RCANFD_RFFIFO_IDX;
/* Transition to channel reset mode */
rcar_canfd_update_bit(priv->base, RCANFD_CCTR(ch),
RCANFD_CCTR_CHMDC_MASK, RCANFD_CCTR_CHDMC_CRESET);
/* Check Channel reset mode */
err = readl_poll_timeout((priv->base + RCANFD_CSTS(ch)), sts,
(sts & RCANFD_CSTS_CRSTSTS), 2, 500000);
if (err)
netdev_err(ndev, "channel %u reset failed\n", ch);
rcar_canfd_disable_channel_interrupts(priv);
/* Disable Common & Rx FIFO */
rcar_canfd_clear_bit(priv->base, RCANFD_CFCC(gpriv, ch, RCANFD_CFFIFO_IDX),
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
RCANFD_CFCC_CFE);
rcar_canfd_clear_bit(priv->base, RCANFD_RFCC(gpriv, ridx), RCANFD_RFCC_RFE);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Set the state as STOPPED */
priv->can.state = CAN_STATE_STOPPED;
}
static int rcar_canfd_close(struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
netif_stop_queue(ndev);
rcar_canfd_stop(ndev);
napi_disable(&priv->napi);
clk_disable_unprepare(gpriv->can_clk);
close_candev(ndev);
phy_power_off(priv->transceiver);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return 0;
}
static netdev_tx_t rcar_canfd_start_xmit(struct sk_buff *skb,
struct net_device *ndev)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct canfd_frame *cf = (struct canfd_frame *)skb->data;
u32 sts = 0, id, dlc;
unsigned long flags;
u32 ch = priv->channel;
if (can_dev_dropped_skb(ndev, skb))
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return NETDEV_TX_OK;
if (cf->can_id & CAN_EFF_FLAG) {
id = cf->can_id & CAN_EFF_MASK;
id |= RCANFD_CFID_CFIDE;
} else {
id = cf->can_id & CAN_SFF_MASK;
}
if (cf->can_id & CAN_RTR_FLAG)
id |= RCANFD_CFID_CFRTR;
dlc = RCANFD_CFPTR_CFDLC(can_fd_len2dlc(cf->len));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) || gpriv->info->shared_can_regs) {
rcar_canfd_write(priv->base,
RCANFD_F_CFID(gpriv, ch, RCANFD_CFFIFO_IDX), id);
rcar_canfd_write(priv->base,
RCANFD_F_CFPTR(gpriv, ch, RCANFD_CFFIFO_IDX), dlc);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (can_is_canfd_skb(skb)) {
/* CAN FD frame format */
sts |= RCANFD_CFFDCSTS_CFFDF;
if (cf->flags & CANFD_BRS)
sts |= RCANFD_CFFDCSTS_CFBRS;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (priv->can.state == CAN_STATE_ERROR_PASSIVE)
sts |= RCANFD_CFFDCSTS_CFESI;
}
rcar_canfd_write(priv->base,
RCANFD_F_CFFDCSTS(gpriv, ch, RCANFD_CFFIFO_IDX), sts);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_put_data(priv, cf,
RCANFD_F_CFDF(gpriv, ch, RCANFD_CFFIFO_IDX, 0));
} else {
rcar_canfd_write(priv->base,
RCANFD_C_CFID(ch, RCANFD_CFFIFO_IDX), id);
rcar_canfd_write(priv->base,
RCANFD_C_CFPTR(ch, RCANFD_CFFIFO_IDX), dlc);
rcar_canfd_put_data(priv, cf,
RCANFD_C_CFDF(ch, RCANFD_CFFIFO_IDX, 0));
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
can_put_echo_skb(skb, ndev, priv->tx_head % RCANFD_FIFO_DEPTH, 0);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
spin_lock_irqsave(&priv->tx_lock, flags);
priv->tx_head++;
/* Stop the queue if we've filled all FIFO entries */
if (priv->tx_head - priv->tx_tail >= RCANFD_FIFO_DEPTH)
netif_stop_queue(ndev);
/* Start Tx: Write 0xff to CFPC to increment the CPU-side
* pointer for the Common FIFO
*/
rcar_canfd_write(priv->base,
RCANFD_CFPCTR(gpriv, ch, RCANFD_CFFIFO_IDX), 0xff);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
spin_unlock_irqrestore(&priv->tx_lock, flags);
return NETDEV_TX_OK;
}
static void rcar_canfd_rx_pkt(struct rcar_canfd_channel *priv)
{
struct net_device *ndev = priv->ndev;
struct net_device_stats *stats = &ndev->stats;
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct canfd_frame *cf;
struct sk_buff *skb;
u32 sts = 0, id, dlc;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u32 ch = priv->channel;
u32 ridx = ch + RCANFD_RFFIFO_IDX;
if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) || gpriv->info->shared_can_regs) {
id = rcar_canfd_read(priv->base, RCANFD_F_RFID(gpriv, ridx));
dlc = rcar_canfd_read(priv->base, RCANFD_F_RFPTR(gpriv, ridx));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
sts = rcar_canfd_read(priv->base, RCANFD_F_RFFDSTS(gpriv, ridx));
if ((priv->can.ctrlmode & CAN_CTRLMODE_FD) &&
sts & RCANFD_RFFDSTS_RFFDF)
skb = alloc_canfd_skb(ndev, &cf);
else
skb = alloc_can_skb(ndev, (struct can_frame **)&cf);
} else {
id = rcar_canfd_read(priv->base, RCANFD_C_RFID(ridx));
dlc = rcar_canfd_read(priv->base, RCANFD_C_RFPTR(ridx));
skb = alloc_can_skb(ndev, (struct can_frame **)&cf);
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (!skb) {
stats->rx_dropped++;
return;
}
if (id & RCANFD_RFID_RFIDE)
cf->can_id = (id & CAN_EFF_MASK) | CAN_EFF_FLAG;
else
cf->can_id = id & CAN_SFF_MASK;
if (priv->can.ctrlmode & CAN_CTRLMODE_FD) {
if (sts & RCANFD_RFFDSTS_RFFDF)
cf->len = can_fd_dlc2len(RCANFD_RFPTR_RFDLC(dlc));
else
cf->len = can_cc_dlc2len(RCANFD_RFPTR_RFDLC(dlc));
if (sts & RCANFD_RFFDSTS_RFESI) {
cf->flags |= CANFD_ESI;
netdev_dbg(ndev, "ESI Error\n");
}
if (!(sts & RCANFD_RFFDSTS_RFFDF) && (id & RCANFD_RFID_RFRTR)) {
cf->can_id |= CAN_RTR_FLAG;
} else {
if (sts & RCANFD_RFFDSTS_RFBRS)
cf->flags |= CANFD_BRS;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_get_data(priv, cf, RCANFD_F_RFDF(gpriv, ridx, 0));
}
} else {
cf->len = can_cc_dlc2len(RCANFD_RFPTR_RFDLC(dlc));
if (id & RCANFD_RFID_RFRTR)
cf->can_id |= CAN_RTR_FLAG;
else if (gpriv->info->shared_can_regs)
rcar_canfd_get_data(priv, cf, RCANFD_F_RFDF(gpriv, ridx, 0));
else
rcar_canfd_get_data(priv, cf, RCANFD_C_RFDF(ridx, 0));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
/* Write 0xff to RFPC to increment the CPU-side
* pointer of the Rx FIFO
*/
rcar_canfd_write(priv->base, RCANFD_RFPCTR(gpriv, ridx), 0xff);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (!(cf->can_id & CAN_RTR_FLAG))
stats->rx_bytes += cf->len;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
stats->rx_packets++;
netif_receive_skb(skb);
}
static int rcar_canfd_rx_poll(struct napi_struct *napi, int quota)
{
struct rcar_canfd_channel *priv =
container_of(napi, struct rcar_canfd_channel, napi);
struct rcar_canfd_global *gpriv = priv->gpriv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
int num_pkts;
u32 sts;
u32 ch = priv->channel;
u32 ridx = ch + RCANFD_RFFIFO_IDX;
for (num_pkts = 0; num_pkts < quota; num_pkts++) {
sts = rcar_canfd_read(priv->base, RCANFD_RFSTS(gpriv, ridx));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Check FIFO empty condition */
if (sts & RCANFD_RFSTS_RFEMP)
break;
rcar_canfd_rx_pkt(priv);
/* Clear interrupt bit */
if (sts & RCANFD_RFSTS_RFIF)
rcar_canfd_write(priv->base, RCANFD_RFSTS(gpriv, ridx),
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
sts & ~RCANFD_RFSTS_RFIF);
}
/* All packets processed */
if (num_pkts < quota) {
can: rcar_canfd: fix possible IRQ storm on high load We have observed rcar_canfd driver entering IRQ storm under high load, with following scenario: - rcar_canfd_global_interrupt() in entered due to Rx available, - napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state - Rx fifo interrupts are masked, - rcar_canfd_global_interrupt() is entered again, this time due to error interrupt (e.g. due to overflow), - since scheduled napi poller has not yet executed, condition for calling napi_schedule_prep() from rcar_canfd_global_interrupt() remains true, thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag in state, - later, napi poller function rcar_canfd_rx_poll() gets executed, and calls napi_complete_done(), - due to NAPIF_STATE_MISSED flag in state, this call does not clear NAPIF_STATE_SCHED flag from state, - on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx interrutps, - Rx interrupt happens, rcar_canfd_global_interrupt() gets called and calls napi_schedule_prep(), - since NAPIF_STATE_SCHED is set in state at this time, this call returns false, - due to that false return, rcar_canfd_global_interrupt() returns without masking Rx interrupt - and this results into IRQ storm: unmasked Rx interrupt happens again and again is misprocessed in the same way. This patch fixes that scenario by unmasking Rx interrupts only when napi_complete_done() returns true, which means it has cleared NAPIF_STATE_SCHED in state. Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-26 16:08:48 +03:00
if (napi_complete_done(napi, num_pkts)) {
/* Enable Rx FIFO interrupts */
rcar_canfd_set_bit(priv->base, RCANFD_RFCC(gpriv, ridx),
can: rcar_canfd: fix possible IRQ storm on high load We have observed rcar_canfd driver entering IRQ storm under high load, with following scenario: - rcar_canfd_global_interrupt() in entered due to Rx available, - napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state - Rx fifo interrupts are masked, - rcar_canfd_global_interrupt() is entered again, this time due to error interrupt (e.g. due to overflow), - since scheduled napi poller has not yet executed, condition for calling napi_schedule_prep() from rcar_canfd_global_interrupt() remains true, thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag in state, - later, napi poller function rcar_canfd_rx_poll() gets executed, and calls napi_complete_done(), - due to NAPIF_STATE_MISSED flag in state, this call does not clear NAPIF_STATE_SCHED flag from state, - on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx interrutps, - Rx interrupt happens, rcar_canfd_global_interrupt() gets called and calls napi_schedule_prep(), - since NAPIF_STATE_SCHED is set in state at this time, this call returns false, - due to that false return, rcar_canfd_global_interrupt() returns without masking Rx interrupt - and this results into IRQ storm: unmasked Rx interrupt happens again and again is misprocessed in the same way. This patch fixes that scenario by unmasking Rx interrupts only when napi_complete_done() returns true, which means it has cleared NAPIF_STATE_SCHED in state. Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-26 16:08:48 +03:00
RCANFD_RFCC_RFIE);
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
return num_pkts;
}
static unsigned int rcar_canfd_get_tdcr(struct rcar_canfd_global *gpriv,
unsigned int ch)
{
u32 sts = readl(&gpriv->fcbase[ch].cfdsts);
u32 tdcr = FIELD_GET(RCANFD_FDSTS_TDCR, sts);
return tdcr & (gpriv->info->tdc_const->tdcv_max - 1);
}
static int rcar_canfd_get_auto_tdcv(const struct net_device *ndev, u32 *tdcv)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
u32 tdco = priv->can.fd.tdc.tdco;
u32 tdcr;
/* Transceiver Delay Compensation Result */
tdcr = rcar_canfd_get_tdcr(priv->gpriv, priv->channel) + 1;
*tdcv = tdcr < tdco ? 0 : tdcr - tdco;
return 0;
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
static int rcar_canfd_do_set_mode(struct net_device *ndev, enum can_mode mode)
{
int err;
switch (mode) {
case CAN_MODE_START:
err = rcar_canfd_start(ndev);
if (err)
return err;
netif_wake_queue(ndev);
return 0;
default:
return -EOPNOTSUPP;
}
}
static int rcar_canfd_get_berr_counter(const struct net_device *ndev,
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct can_berr_counter *bec)
{
struct rcar_canfd_channel *priv = netdev_priv(ndev);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
u32 val, ch = priv->channel;
/* Peripheral clock is already enabled in probe */
val = rcar_canfd_read(priv->base, RCANFD_CSTS(ch));
bec->txerr = RCANFD_CSTS_TECCNT(val);
bec->rxerr = RCANFD_CSTS_RECCNT(val);
return 0;
}
static const struct net_device_ops rcar_canfd_netdev_ops = {
.ndo_open = rcar_canfd_open,
.ndo_stop = rcar_canfd_close,
.ndo_start_xmit = rcar_canfd_start_xmit,
.ndo_change_mtu = can_change_mtu,
};
static const struct ethtool_ops rcar_canfd_ethtool_ops = {
.get_ts_info = ethtool_op_get_ts_info,
};
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
static int rcar_canfd_channel_probe(struct rcar_canfd_global *gpriv, u32 ch,
u32 fcan_freq, struct phy *transceiver)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{
const struct rcar_canfd_hw_info *info = gpriv->info;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct platform_device *pdev = gpriv->pdev;
struct device *dev = &pdev->dev;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
struct rcar_canfd_channel *priv;
struct net_device *ndev;
int err = -ENODEV;
ndev = alloc_candev(sizeof(*priv), RCANFD_FIFO_DEPTH);
if (!ndev)
return -ENOMEM;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
priv = netdev_priv(ndev);
ndev->netdev_ops = &rcar_canfd_netdev_ops;
ndev->ethtool_ops = &rcar_canfd_ethtool_ops;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
ndev->flags |= IFF_ECHO;
priv->ndev = ndev;
priv->base = gpriv->base;
priv->transceiver = transceiver;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
priv->channel = ch;
priv->gpriv = gpriv;
if (transceiver)
priv->can.bitrate_max = transceiver->attrs.max_link_rate;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
priv->can.clock.freq = fcan_freq;
dev_info(dev, "can_clk rate is %u\n", priv->can.clock.freq);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (info->multi_channel_irqs) {
char *irq_name;
char name[10];
int err_irq;
int tx_irq;
scnprintf(name, sizeof(name), "ch%u_err", ch);
err_irq = platform_get_irq_byname(pdev, name);
if (err_irq < 0) {
err = err_irq;
goto fail;
}
scnprintf(name, sizeof(name), "ch%u_trx", ch);
tx_irq = platform_get_irq_byname(pdev, name);
if (tx_irq < 0) {
err = tx_irq;
goto fail;
}
irq_name = devm_kasprintf(dev, GFP_KERNEL, "canfd.ch%d_err",
ch);
if (!irq_name) {
err = -ENOMEM;
goto fail;
}
err = devm_request_irq(dev, err_irq,
rcar_canfd_channel_err_interrupt, 0,
irq_name, priv);
if (err) {
dev_err(dev, "devm_request_irq CH Err %d failed: %pe\n",
err_irq, ERR_PTR(err));
goto fail;
}
irq_name = devm_kasprintf(dev, GFP_KERNEL, "canfd.ch%d_trx",
ch);
if (!irq_name) {
err = -ENOMEM;
goto fail;
}
err = devm_request_irq(dev, tx_irq,
rcar_canfd_channel_tx_interrupt, 0,
irq_name, priv);
if (err) {
dev_err(dev, "devm_request_irq Tx %d failed: %pe\n",
tx_irq, ERR_PTR(err));
goto fail;
}
}
if (gpriv->fdmode) {
priv->can.bittiming_const = gpriv->info->nom_bittiming;
priv->can.fd.data_bittiming_const = gpriv->info->data_bittiming;
priv->can.fd.tdc_const = gpriv->info->tdc_const;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Controller starts in CAN FD only mode */
err = can_set_static_ctrlmode(ndev, CAN_CTRLMODE_FD);
if (err)
goto fail;
priv->can.ctrlmode_supported = CAN_CTRLMODE_BERR_REPORTING |
CAN_CTRLMODE_TDC_AUTO |
CAN_CTRLMODE_TDC_MANUAL;
priv->can.fd.do_get_auto_tdcv = rcar_canfd_get_auto_tdcv;
} else {
/* Controller starts in Classical CAN only mode */
priv->can.bittiming_const = &rcar_canfd_bittiming_const;
priv->can.ctrlmode_supported = CAN_CTRLMODE_BERR_REPORTING;
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
priv->can.do_set_mode = rcar_canfd_do_set_mode;
priv->can.do_get_berr_counter = rcar_canfd_get_berr_counter;
SET_NETDEV_DEV(ndev, dev);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
netif_napi_add_weight(ndev, &priv->napi, rcar_canfd_rx_poll,
RCANFD_NAPI_WEIGHT);
spin_lock_init(&priv->tx_lock);
gpriv->ch[priv->channel] = priv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
err = register_candev(ndev);
if (err) {
dev_err(dev, "register_candev() failed: %pe\n", ERR_PTR(err));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
goto fail_candev;
}
dev_info(dev, "device registered (channel %u)\n", priv->channel);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return 0;
fail_candev:
netif_napi_del(&priv->napi);
fail:
free_candev(ndev);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return err;
}
static void rcar_canfd_channel_remove(struct rcar_canfd_global *gpriv, u32 ch)
{
struct rcar_canfd_channel *priv = gpriv->ch[ch];
if (priv) {
unregister_candev(priv->ndev);
netif_napi_del(&priv->napi);
free_candev(priv->ndev);
}
}
static int rcar_canfd_probe(struct platform_device *pdev)
{
struct phy *transceivers[RCANFD_NUM_CHANNELS] = { NULL, };
const struct rcar_canfd_hw_info *info;
struct device *dev = &pdev->dev;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
void __iomem *addr;
u32 sts, ch, fcan_freq;
struct rcar_canfd_global *gpriv;
struct device_node *of_child;
unsigned long channels_mask = 0;
int err, ch_irq, g_irq;
int g_err_irq, g_recc_irq;
u32 rule_entry = 0;
bool fdmode = true; /* CAN FD only mode - default */
char name[9] = "channelX";
struct clk *clk_ram;
int i;
info = of_device_get_match_data(dev);
if (of_property_read_bool(dev->of_node, "renesas,no-can-fd"))
fdmode = false; /* Classical CAN only mode */
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
for (i = 0; i < info->max_channels; ++i) {
name[7] = '0' + i;
of_child = of_get_available_child_by_name(dev->of_node, name);
if (of_child) {
channels_mask |= BIT(i);
transceivers[i] = devm_of_phy_optional_get(dev,
of_child, NULL);
of_node_put(of_child);
}
if (IS_ERR(transceivers[i]))
return PTR_ERR(transceivers[i]);
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (info->shared_global_irqs) {
ch_irq = platform_get_irq_byname_optional(pdev, "ch_int");
if (ch_irq < 0) {
/* For backward compatibility get irq by index */
ch_irq = platform_get_irq(pdev, 0);
if (ch_irq < 0)
return ch_irq;
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
g_irq = platform_get_irq_byname_optional(pdev, "g_int");
if (g_irq < 0) {
/* For backward compatibility get irq by index */
g_irq = platform_get_irq(pdev, 1);
if (g_irq < 0)
return g_irq;
}
} else {
g_err_irq = platform_get_irq_byname(pdev, "g_err");
if (g_err_irq < 0)
return g_err_irq;
g_recc_irq = platform_get_irq_byname(pdev, "g_recc");
if (g_recc_irq < 0)
return g_recc_irq;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
/* Global controller context */
gpriv = devm_kzalloc(dev, sizeof(*gpriv), GFP_KERNEL);
if (!gpriv)
return -ENOMEM;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
gpriv->pdev = pdev;
gpriv->channels_mask = channels_mask;
gpriv->fdmode = fdmode;
gpriv->info = info;
gpriv->rstc1 = devm_reset_control_get_optional_exclusive(dev, "rstp_n");
if (IS_ERR(gpriv->rstc1))
return dev_err_probe(dev, PTR_ERR(gpriv->rstc1),
"failed to get rstp_n\n");
gpriv->rstc2 = devm_reset_control_get_optional_exclusive(dev, "rstc_n");
if (IS_ERR(gpriv->rstc2))
return dev_err_probe(dev, PTR_ERR(gpriv->rstc2),
"failed to get rstc_n\n");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Peripheral clock */
gpriv->clkp = devm_clk_get(dev, "fck");
if (IS_ERR(gpriv->clkp))
return dev_err_probe(dev, PTR_ERR(gpriv->clkp),
"cannot get peripheral clock\n");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* fCAN clock: Pick External clock. If not available fallback to
* CANFD clock
*/
gpriv->can_clk = devm_clk_get(dev, "can_clk");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (IS_ERR(gpriv->can_clk) || (clk_get_rate(gpriv->can_clk) == 0)) {
gpriv->can_clk = devm_clk_get(dev, "canfd");
if (IS_ERR(gpriv->can_clk))
return dev_err_probe(dev, PTR_ERR(gpriv->can_clk),
"cannot get canfd clock\n");
/* CANFD clock may be further divided within the IP */
fcan_freq = clk_get_rate(gpriv->can_clk) / info->postdiv;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
} else {
fcan_freq = clk_get_rate(gpriv->can_clk);
gpriv->extclk = gpriv->info->external_clk;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
clk_ram = devm_clk_get_optional_enabled(dev, "ram_clk");
if (IS_ERR(clk_ram))
return dev_err_probe(dev, PTR_ERR(clk_ram),
"cannot get enabled ram clock\n");
addr = devm_platform_ioremap_resource(pdev, 0);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (IS_ERR(addr)) {
err = PTR_ERR(addr);
goto fail_dev;
}
gpriv->base = addr;
gpriv->fcbase = addr + gpriv->info->regs->coffset;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Request IRQ that's common for both channels */
if (info->shared_global_irqs) {
err = devm_request_irq(dev, ch_irq,
rcar_canfd_channel_interrupt, 0,
"canfd.ch_int", gpriv);
if (err) {
dev_err(dev, "devm_request_irq %d failed: %pe\n",
ch_irq, ERR_PTR(err));
goto fail_dev;
}
err = devm_request_irq(dev, g_irq, rcar_canfd_global_interrupt,
0, "canfd.g_int", gpriv);
if (err) {
dev_err(dev, "devm_request_irq %d failed: %pe\n",
g_irq, ERR_PTR(err));
goto fail_dev;
}
} else {
err = devm_request_irq(dev, g_recc_irq,
rcar_canfd_global_receive_fifo_interrupt, 0,
"canfd.g_recc", gpriv);
if (err) {
dev_err(dev, "devm_request_irq %d failed: %pe\n",
g_recc_irq, ERR_PTR(err));
goto fail_dev;
}
err = devm_request_irq(dev, g_err_irq,
rcar_canfd_global_err_interrupt, 0,
"canfd.g_err", gpriv);
if (err) {
dev_err(dev, "devm_request_irq %d failed: %pe\n",
g_err_irq, ERR_PTR(err));
goto fail_dev;
}
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
err = reset_control_reset(gpriv->rstc1);
if (err)
goto fail_dev;
err = reset_control_reset(gpriv->rstc2);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (err) {
reset_control_assert(gpriv->rstc1);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
goto fail_dev;
}
/* Enable peripheral clock for register access */
err = clk_prepare_enable(gpriv->clkp);
if (err) {
dev_err(dev, "failed to enable peripheral clock: %pe\n",
ERR_PTR(err));
goto fail_reset;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
err = rcar_canfd_reset_controller(gpriv);
if (err) {
dev_err(dev, "reset controller failed: %pe\n", ERR_PTR(err));
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
goto fail_clk;
}
/* Controller in Global reset & Channel reset mode */
rcar_canfd_configure_controller(gpriv);
/* Configure per channel attributes */
for_each_set_bit(ch, &gpriv->channels_mask, info->max_channels) {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
/* Configure Channel's Rx fifo */
rcar_canfd_configure_rx(gpriv, ch);
/* Configure Channel's Tx (Common) fifo */
rcar_canfd_configure_tx(gpriv, ch);
/* Configure receive rules */
rcar_canfd_configure_afl_rules(gpriv, ch, rule_entry);
rule_entry += RCANFD_CHANNEL_NUMRULES;
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
/* Configure common interrupts */
rcar_canfd_enable_global_interrupts(gpriv);
/* Start Global operation mode */
rcar_canfd_update_bit(gpriv->base, RCANFD_GCTR, RCANFD_GCTR_GMDC_MASK,
RCANFD_GCTR_GMDC_GOPM);
/* Verify mode change */
err = readl_poll_timeout((gpriv->base + RCANFD_GSTS), sts,
!(sts & RCANFD_GSTS_GNOPM), 2, 500000);
if (err) {
dev_err(dev, "global operational mode failed\n");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
goto fail_mode;
}
for_each_set_bit(ch, &gpriv->channels_mask, info->max_channels) {
err = rcar_canfd_channel_probe(gpriv, ch, fcan_freq,
transceivers[ch]);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
if (err)
goto fail_channel;
}
platform_set_drvdata(pdev, gpriv);
dev_info(dev, "global operational state (%s clk, %s mode)\n",
gpriv->extclk ? "ext" : "canfd",
gpriv->fdmode ? "fd" : "classical");
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
return 0;
fail_channel:
for_each_set_bit(ch, &gpriv->channels_mask, info->max_channels)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_channel_remove(gpriv, ch);
fail_mode:
rcar_canfd_disable_global_interrupts(gpriv);
fail_clk:
clk_disable_unprepare(gpriv->clkp);
fail_reset:
reset_control_assert(gpriv->rstc1);
reset_control_assert(gpriv->rstc2);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
fail_dev:
return err;
}
static void rcar_canfd_remove(struct platform_device *pdev)
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{
struct rcar_canfd_global *gpriv = platform_get_drvdata(pdev);
u32 ch;
rcar_canfd_reset_controller(gpriv);
rcar_canfd_disable_global_interrupts(gpriv);
for_each_set_bit(ch, &gpriv->channels_mask, gpriv->info->max_channels) {
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
rcar_canfd_disable_channel_interrupts(gpriv->ch[ch]);
rcar_canfd_channel_remove(gpriv, ch);
}
/* Enter global sleep mode */
rcar_canfd_set_bit(gpriv->base, RCANFD_GCTR, RCANFD_GCTR_GSLPR);
clk_disable_unprepare(gpriv->clkp);
reset_control_assert(gpriv->rstc1);
reset_control_assert(gpriv->rstc2);
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
}
static int __maybe_unused rcar_canfd_suspend(struct device *dev)
{
return 0;
}
static int __maybe_unused rcar_canfd_resume(struct device *dev)
{
return 0;
}
static SIMPLE_DEV_PM_OPS(rcar_canfd_pm_ops, rcar_canfd_suspend,
rcar_canfd_resume);
static const __maybe_unused struct of_device_id rcar_canfd_of_table[] = {
{ .compatible = "renesas,r8a779a0-canfd", .data = &rcar_gen4_hw_info },
{ .compatible = "renesas,r9a09g047-canfd", .data = &r9a09g047_hw_info },
{ .compatible = "renesas,rcar-gen3-canfd", .data = &rcar_gen3_hw_info },
{ .compatible = "renesas,rcar-gen4-canfd", .data = &rcar_gen4_hw_info },
{ .compatible = "renesas,rzg2l-canfd", .data = &rzg2l_hw_info },
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
{ }
};
MODULE_DEVICE_TABLE(of, rcar_canfd_of_table);
static struct platform_driver rcar_canfd_driver = {
.driver = {
.name = RCANFD_DRV_NAME,
.of_match_table = of_match_ptr(rcar_canfd_of_table),
.pm = &rcar_canfd_pm_ops,
},
.probe = rcar_canfd_probe,
.remove = rcar_canfd_remove,
can: rcar_canfd: Add Renesas R-Car CAN FD driver This patch adds support for the CAN FD controller found in Renesas R-Car SoCs. The controller operates in CAN FD only mode by default. CAN FD mode supports both Classical CAN & CAN FD frame formats. The controller supports ISO 11898-1:2015 CAN FD format only. This controller supports two channels and the driver can enable either or both of the channels. Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one per channel) for transmission. Rx filter rules are configured to the minimum (one per channel) and it accepts Standard, Extended, Data & Remote Frame combinations. Note: There are few documentation errors in R-Car Gen3 Hardware User Manual v0.5E with respect to CAN FD controller. They are listed below: 1. CAN FD interrupt numbers 29 & 30 are listed as per channel interrupts. However, they are common to both channels (i.e.) they are global and channel interrupts respectively. 2. CANFD clock is derived from PLL1. This is not documented. 3. CANFD clock is further divided by (1/2) within the CAN FD controller. This is not documented. 4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It is specified 4 Tq in the manual. 5. The maximum number of message RAM area the controller can use is 3584 bytes. It is specified 10752 bytes in the manual. Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2016-06-17 09:20:55 +01:00
};
module_platform_driver(rcar_canfd_driver);
MODULE_AUTHOR("Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>");
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("CAN FD driver for Renesas R-Car SoC");
MODULE_ALIAS("platform:" RCANFD_DRV_NAME);