License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 15:07:57 +01:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
2005-04-16 15:20:36 -07:00
|
|
|
#ifndef _PARISC_CACHEFLUSH_H
|
|
|
|
|
#define _PARISC_CACHEFLUSH_H
|
|
|
|
|
|
|
|
|
|
#include <linux/mm.h>
|
2010-04-11 16:36:14 +00:00
|
|
|
#include <linux/uaccess.h>
|
2011-04-15 12:37:22 -05:00
|
|
|
#include <asm/tlbflush.h>
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
/* The usual comment is "Caches aren't brain-dead on the <architecture>".
|
|
|
|
|
* Unfortunately, that doesn't apply to PA-RISC. */
|
|
|
|
|
|
2022-03-12 21:03:33 +01:00
|
|
|
#include <linux/jump_label.h>
|
|
|
|
|
|
|
|
|
|
DECLARE_STATIC_KEY_TRUE(parisc_has_cache);
|
|
|
|
|
DECLARE_STATIC_KEY_TRUE(parisc_has_dcache);
|
|
|
|
|
DECLARE_STATIC_KEY_TRUE(parisc_has_icache);
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-12-12 17:14:57 +00:00
|
|
|
#define flush_cache_dup_mm(mm) flush_cache_mm(mm)
|
|
|
|
|
|
2006-12-12 05:51:54 -08:00
|
|
|
void flush_user_icache_range_asm(unsigned long, unsigned long);
|
|
|
|
|
void flush_kernel_icache_range_asm(unsigned long, unsigned long);
|
|
|
|
|
void flush_user_dcache_range_asm(unsigned long, unsigned long);
|
|
|
|
|
void flush_kernel_dcache_range_asm(unsigned long, unsigned long);
|
2018-02-27 08:16:07 -05:00
|
|
|
void purge_kernel_dcache_range_asm(unsigned long, unsigned long);
|
2022-07-06 13:15:19 +02:00
|
|
|
void flush_kernel_dcache_page_asm(const void *addr);
|
2006-12-12 05:51:54 -08:00
|
|
|
void flush_kernel_icache_page(void *);
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-12-12 05:51:54 -08:00
|
|
|
/* Cache flush operations */
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-12-12 05:51:54 -08:00
|
|
|
void flush_cache_all_local(void);
|
|
|
|
|
void flush_cache_all(void);
|
|
|
|
|
void flush_cache_mm(struct mm_struct *mm);
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-12-12 05:51:54 -08:00
|
|
|
#define flush_kernel_dcache_range(start,size) \
|
|
|
|
|
flush_kernel_dcache_range_asm((start), (start)+(size));
|
2011-01-20 12:54:18 -06:00
|
|
|
|
parisc: Try to fix random segmentation faults in package builds
PA-RISC systems with PA8800 and PA8900 processors have had problems
with random segmentation faults for many years. Systems with earlier
processors are much more stable.
Systems with PA8800 and PA8900 processors have a large L2 cache which
needs per page flushing for decent performance when a large range is
flushed. The combined cache in these systems is also more sensitive to
non-equivalent aliases than the caches in earlier systems.
The majority of random segmentation faults that I have looked at
appear to be memory corruption in memory allocated using mmap and
malloc.
My first attempt at fixing the random faults didn't work. On
reviewing the cache code, I realized that there were two issues
which the existing code didn't handle correctly. Both relate
to cache move-in. Another issue is that the present bit in PTEs
is racy.
1) PA-RISC caches have a mind of their own and they can speculatively
load data and instructions for a page as long as there is a entry in
the TLB for the page which allows move-in. TLBs are local to each
CPU. Thus, the TLB entry for a page must be purged before flushing
the page. This is particularly important on SMP systems.
In some of the flush routines, the flush routine would be called
and then the TLB entry would be purged. This was because the flush
routine needed the TLB entry to do the flush.
2) My initial approach to trying the fix the random faults was to
try and use flush_cache_page_if_present for all flush operations.
This actually made things worse and led to a couple of hardware
lockups. It finally dawned on me that some lines weren't being
flushed because the pte check code was racy. This resulted in
random inequivalent mappings to physical pages.
The __flush_cache_page tmpalias flush sets up its own TLB entry
and it doesn't need the existing TLB entry. As long as we can find
the pte pointer for the vm page, we can get the pfn and physical
address of the page. We can also purge the TLB entry for the page
before doing the flush. Further, __flush_cache_page uses a special
TLB entry that inhibits cache move-in.
When switching page mappings, we need to ensure that lines are
removed from the cache. It is not sufficient to just flush the
lines to memory as they may come back.
This made it clear that we needed to implement all the required
flush operations using tmpalias routines. This includes flushes
for user and kernel pages.
After modifying the code to use tmpalias flushes, it became clear
that the random segmentation faults were not fully resolved. The
frequency of faults was worse on systems with a 64 MB L2 (PA8900)
and systems with more CPUs (rp4440).
The warning that I added to flush_cache_page_if_present to detect
pages that couldn't be flushed triggered frequently on some systems.
Helge and I looked at the pages that couldn't be flushed and found
that the PTE was either cleared or for a swap page. Ignoring pages
that were swapped out seemed okay but pages with cleared PTEs seemed
problematic.
I looked at routines related to pte_clear and noticed ptep_clear_flush.
The default implementation just flushes the TLB entry. However, it was
obvious that on parisc we need to flush the cache page as well. If
we don't flush the cache page, stale lines will be left in the cache
and cause random corruption. Once a PTE is cleared, there is no way
to find the physical address associated with the PTE and flush the
associated page at a later time.
I implemented an updated change with a parisc specific version of
ptep_clear_flush. It fixed the random data corruption on Helge's rp4440
and rp3440, as well as on my c8000.
At this point, I realized that I could restore the code where we only
flush in flush_cache_page_if_present if the page has been accessed.
However, for this, we also need to flush the cache when the accessed
bit is cleared in ptep_clear_flush_young to keep things synchronized.
The default implementation only flushes the TLB entry.
Other changes in this version are:
1) Implement parisc specific version of ptep_get. It's identical to
default but needed in arch/parisc/include/asm/pgtable.h.
2) Revise parisc implementation of ptep_test_and_clear_young to use
ptep_get (READ_ONCE).
3) Drop parisc implementation of ptep_get_and_clear. We can use default.
4) Revise flush_kernel_vmap_range and invalidate_kernel_vmap_range to
use full data cache flush.
5) Move flush_cache_vmap and flush_cache_vunmap to cache.c. Handle
VM_IOREMAP case in flush_cache_vmap.
At this time, I don't know whether it is better to always flush when
the PTE present bit is set or when both the accessed and present bits
are set. The later saves flushing pages that haven't been accessed,
but we need to flush in ptep_clear_flush_young. It also needs a page
table lookup to find the PTE pointer. The lpa instruction only needs
a page table lookup when the PTE entry isn't in the TLB.
We don't atomically handle setting and clearing the _PAGE_ACCESSED bit.
If we miss an update, we may miss a flush and the cache may get corrupted.
Whether the current code is effectively atomic depends on process control.
When CONFIG_FLUSH_PAGE_ACCESSED is set to zero, the page will eventually
be flushed when the PTE is cleared or in flush_cache_page_if_present. The
_PAGE_ACCESSED bit is not used, so the problem is avoided.
The flush method can be selected using the CONFIG_FLUSH_PAGE_ACCESSED
define in cache.c. The default is 0. I didn't see a large difference
in performance.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Helge Deller <deller@gmx.de>
2024-06-10 18:47:07 +00:00
|
|
|
/* The only way to flush a vmap range is to flush whole cache */
|
2021-09-02 14:56:36 -07:00
|
|
|
#define ARCH_IMPLEMENTS_FLUSH_KERNEL_VMAP_RANGE 1
|
2017-03-11 18:03:34 -05:00
|
|
|
void flush_kernel_vmap_range(void *vaddr, int size);
|
|
|
|
|
void invalidate_kernel_vmap_range(void *vaddr, int size);
|
2005-04-16 15:20:36 -07:00
|
|
|
|
parisc: Try to fix random segmentation faults in package builds
PA-RISC systems with PA8800 and PA8900 processors have had problems
with random segmentation faults for many years. Systems with earlier
processors are much more stable.
Systems with PA8800 and PA8900 processors have a large L2 cache which
needs per page flushing for decent performance when a large range is
flushed. The combined cache in these systems is also more sensitive to
non-equivalent aliases than the caches in earlier systems.
The majority of random segmentation faults that I have looked at
appear to be memory corruption in memory allocated using mmap and
malloc.
My first attempt at fixing the random faults didn't work. On
reviewing the cache code, I realized that there were two issues
which the existing code didn't handle correctly. Both relate
to cache move-in. Another issue is that the present bit in PTEs
is racy.
1) PA-RISC caches have a mind of their own and they can speculatively
load data and instructions for a page as long as there is a entry in
the TLB for the page which allows move-in. TLBs are local to each
CPU. Thus, the TLB entry for a page must be purged before flushing
the page. This is particularly important on SMP systems.
In some of the flush routines, the flush routine would be called
and then the TLB entry would be purged. This was because the flush
routine needed the TLB entry to do the flush.
2) My initial approach to trying the fix the random faults was to
try and use flush_cache_page_if_present for all flush operations.
This actually made things worse and led to a couple of hardware
lockups. It finally dawned on me that some lines weren't being
flushed because the pte check code was racy. This resulted in
random inequivalent mappings to physical pages.
The __flush_cache_page tmpalias flush sets up its own TLB entry
and it doesn't need the existing TLB entry. As long as we can find
the pte pointer for the vm page, we can get the pfn and physical
address of the page. We can also purge the TLB entry for the page
before doing the flush. Further, __flush_cache_page uses a special
TLB entry that inhibits cache move-in.
When switching page mappings, we need to ensure that lines are
removed from the cache. It is not sufficient to just flush the
lines to memory as they may come back.
This made it clear that we needed to implement all the required
flush operations using tmpalias routines. This includes flushes
for user and kernel pages.
After modifying the code to use tmpalias flushes, it became clear
that the random segmentation faults were not fully resolved. The
frequency of faults was worse on systems with a 64 MB L2 (PA8900)
and systems with more CPUs (rp4440).
The warning that I added to flush_cache_page_if_present to detect
pages that couldn't be flushed triggered frequently on some systems.
Helge and I looked at the pages that couldn't be flushed and found
that the PTE was either cleared or for a swap page. Ignoring pages
that were swapped out seemed okay but pages with cleared PTEs seemed
problematic.
I looked at routines related to pte_clear and noticed ptep_clear_flush.
The default implementation just flushes the TLB entry. However, it was
obvious that on parisc we need to flush the cache page as well. If
we don't flush the cache page, stale lines will be left in the cache
and cause random corruption. Once a PTE is cleared, there is no way
to find the physical address associated with the PTE and flush the
associated page at a later time.
I implemented an updated change with a parisc specific version of
ptep_clear_flush. It fixed the random data corruption on Helge's rp4440
and rp3440, as well as on my c8000.
At this point, I realized that I could restore the code where we only
flush in flush_cache_page_if_present if the page has been accessed.
However, for this, we also need to flush the cache when the accessed
bit is cleared in ptep_clear_flush_young to keep things synchronized.
The default implementation only flushes the TLB entry.
Other changes in this version are:
1) Implement parisc specific version of ptep_get. It's identical to
default but needed in arch/parisc/include/asm/pgtable.h.
2) Revise parisc implementation of ptep_test_and_clear_young to use
ptep_get (READ_ONCE).
3) Drop parisc implementation of ptep_get_and_clear. We can use default.
4) Revise flush_kernel_vmap_range and invalidate_kernel_vmap_range to
use full data cache flush.
5) Move flush_cache_vmap and flush_cache_vunmap to cache.c. Handle
VM_IOREMAP case in flush_cache_vmap.
At this time, I don't know whether it is better to always flush when
the PTE present bit is set or when both the accessed and present bits
are set. The later saves flushing pages that haven't been accessed,
but we need to flush in ptep_clear_flush_young. It also needs a page
table lookup to find the PTE pointer. The lpa instruction only needs
a page table lookup when the PTE entry isn't in the TLB.
We don't atomically handle setting and clearing the _PAGE_ACCESSED bit.
If we miss an update, we may miss a flush and the cache may get corrupted.
Whether the current code is effectively atomic depends on process control.
When CONFIG_FLUSH_PAGE_ACCESSED is set to zero, the page will eventually
be flushed when the PTE is cleared or in flush_cache_page_if_present. The
_PAGE_ACCESSED bit is not used, so the problem is avoided.
The flush method can be selected using the CONFIG_FLUSH_PAGE_ACCESSED
define in cache.c. The default is 0. I didn't see a large difference
in performance.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Helge Deller <deller@gmx.de>
2024-06-10 18:47:07 +00:00
|
|
|
void flush_cache_vmap(unsigned long start, unsigned long end);
|
2023-12-12 22:34:56 +01:00
|
|
|
#define flush_cache_vmap_early(start, end) do { } while (0)
|
parisc: Try to fix random segmentation faults in package builds
PA-RISC systems with PA8800 and PA8900 processors have had problems
with random segmentation faults for many years. Systems with earlier
processors are much more stable.
Systems with PA8800 and PA8900 processors have a large L2 cache which
needs per page flushing for decent performance when a large range is
flushed. The combined cache in these systems is also more sensitive to
non-equivalent aliases than the caches in earlier systems.
The majority of random segmentation faults that I have looked at
appear to be memory corruption in memory allocated using mmap and
malloc.
My first attempt at fixing the random faults didn't work. On
reviewing the cache code, I realized that there were two issues
which the existing code didn't handle correctly. Both relate
to cache move-in. Another issue is that the present bit in PTEs
is racy.
1) PA-RISC caches have a mind of their own and they can speculatively
load data and instructions for a page as long as there is a entry in
the TLB for the page which allows move-in. TLBs are local to each
CPU. Thus, the TLB entry for a page must be purged before flushing
the page. This is particularly important on SMP systems.
In some of the flush routines, the flush routine would be called
and then the TLB entry would be purged. This was because the flush
routine needed the TLB entry to do the flush.
2) My initial approach to trying the fix the random faults was to
try and use flush_cache_page_if_present for all flush operations.
This actually made things worse and led to a couple of hardware
lockups. It finally dawned on me that some lines weren't being
flushed because the pte check code was racy. This resulted in
random inequivalent mappings to physical pages.
The __flush_cache_page tmpalias flush sets up its own TLB entry
and it doesn't need the existing TLB entry. As long as we can find
the pte pointer for the vm page, we can get the pfn and physical
address of the page. We can also purge the TLB entry for the page
before doing the flush. Further, __flush_cache_page uses a special
TLB entry that inhibits cache move-in.
When switching page mappings, we need to ensure that lines are
removed from the cache. It is not sufficient to just flush the
lines to memory as they may come back.
This made it clear that we needed to implement all the required
flush operations using tmpalias routines. This includes flushes
for user and kernel pages.
After modifying the code to use tmpalias flushes, it became clear
that the random segmentation faults were not fully resolved. The
frequency of faults was worse on systems with a 64 MB L2 (PA8900)
and systems with more CPUs (rp4440).
The warning that I added to flush_cache_page_if_present to detect
pages that couldn't be flushed triggered frequently on some systems.
Helge and I looked at the pages that couldn't be flushed and found
that the PTE was either cleared or for a swap page. Ignoring pages
that were swapped out seemed okay but pages with cleared PTEs seemed
problematic.
I looked at routines related to pte_clear and noticed ptep_clear_flush.
The default implementation just flushes the TLB entry. However, it was
obvious that on parisc we need to flush the cache page as well. If
we don't flush the cache page, stale lines will be left in the cache
and cause random corruption. Once a PTE is cleared, there is no way
to find the physical address associated with the PTE and flush the
associated page at a later time.
I implemented an updated change with a parisc specific version of
ptep_clear_flush. It fixed the random data corruption on Helge's rp4440
and rp3440, as well as on my c8000.
At this point, I realized that I could restore the code where we only
flush in flush_cache_page_if_present if the page has been accessed.
However, for this, we also need to flush the cache when the accessed
bit is cleared in ptep_clear_flush_young to keep things synchronized.
The default implementation only flushes the TLB entry.
Other changes in this version are:
1) Implement parisc specific version of ptep_get. It's identical to
default but needed in arch/parisc/include/asm/pgtable.h.
2) Revise parisc implementation of ptep_test_and_clear_young to use
ptep_get (READ_ONCE).
3) Drop parisc implementation of ptep_get_and_clear. We can use default.
4) Revise flush_kernel_vmap_range and invalidate_kernel_vmap_range to
use full data cache flush.
5) Move flush_cache_vmap and flush_cache_vunmap to cache.c. Handle
VM_IOREMAP case in flush_cache_vmap.
At this time, I don't know whether it is better to always flush when
the PTE present bit is set or when both the accessed and present bits
are set. The later saves flushing pages that haven't been accessed,
but we need to flush in ptep_clear_flush_young. It also needs a page
table lookup to find the PTE pointer. The lpa instruction only needs
a page table lookup when the PTE entry isn't in the TLB.
We don't atomically handle setting and clearing the _PAGE_ACCESSED bit.
If we miss an update, we may miss a flush and the cache may get corrupted.
Whether the current code is effectively atomic depends on process control.
When CONFIG_FLUSH_PAGE_ACCESSED is set to zero, the page will eventually
be flushed when the PTE is cleared or in flush_cache_page_if_present. The
_PAGE_ACCESSED bit is not used, so the problem is avoided.
The flush method can be selected using the CONFIG_FLUSH_PAGE_ACCESSED
define in cache.c. The default is 0. I didn't see a large difference
in performance.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Helge Deller <deller@gmx.de>
2024-06-10 18:47:07 +00:00
|
|
|
void flush_cache_vunmap(unsigned long start, unsigned long end);
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2023-08-02 16:13:48 +01:00
|
|
|
void flush_dcache_folio(struct folio *folio);
|
|
|
|
|
#define flush_dcache_folio flush_dcache_folio
|
2009-11-26 09:16:19 +01:00
|
|
|
#define ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE 1
|
2023-08-02 16:13:48 +01:00
|
|
|
static inline void flush_dcache_page(struct page *page)
|
|
|
|
|
{
|
|
|
|
|
flush_dcache_folio(page_folio(page));
|
|
|
|
|
}
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2018-04-10 16:36:56 -07:00
|
|
|
#define flush_dcache_mmap_lock(mapping) xa_lock_irq(&mapping->i_pages)
|
|
|
|
|
#define flush_dcache_mmap_unlock(mapping) xa_unlock_irq(&mapping->i_pages)
|
2023-05-24 17:07:07 +02:00
|
|
|
#define flush_dcache_mmap_lock_irqsave(mapping, flags) \
|
|
|
|
|
xa_lock_irqsave(&mapping->i_pages, flags)
|
|
|
|
|
#define flush_dcache_mmap_unlock_irqrestore(mapping, flags) \
|
|
|
|
|
xa_unlock_irqrestore(&mapping->i_pages, flags)
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2023-08-02 16:13:48 +01:00
|
|
|
void flush_icache_pages(struct vm_area_struct *vma, struct page *page,
|
|
|
|
|
unsigned int nr);
|
2023-08-02 16:13:59 +01:00
|
|
|
#define flush_icache_pages flush_icache_pages
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-12-12 05:51:54 -08:00
|
|
|
#define flush_icache_range(s,e) do { \
|
|
|
|
|
flush_kernel_dcache_range_asm(s,e); \
|
|
|
|
|
flush_kernel_icache_range_asm(s,e); \
|
|
|
|
|
} while (0)
|
2005-04-16 15:20:36 -07:00
|
|
|
|
parisc: Rewrite cache flush code for PA8800/PA8900
Originally, I was convinced that we needed to use tmpalias flushes
everwhere, for both user and kernel flushes. However, when I modified
flush_kernel_dcache_page_addr, to use a tmpalias flush, my c8000
would crash quite early when booting.
The PDC returns alias values of 0 for the icache and dcache. This
indicates that either the alias boundary is greater than 16MB or
equivalent aliasing doesn't work. I modified the tmpalias code to
make it easy to try alternate boundaries. I tried boundaries up to
128MB but still kernel tmpalias flushes didn't work on c8000.
This led me to conclude that tmpalias flushes don't work on PA8800
and PA8900 machines, and that we needed to flush directly using the
virtual address of user and kernel pages. This is likely the major
cause of instability on the c8000 and rp34xx machines.
Flushing user pages requires doing a temporary context switch as we
have to flush pages that don't belong to the current context. Further,
we have to deal with pages that aren't present. If a page isn't
present, the flush instructions fault on every line.
Other code has been rearranged and simplified based on testing. For
example, I introduced a flush_cache_dup_mm routine. flush_cache_mm
and flush_cache_dup_mm differ in that flush_cache_mm calls
purge_cache_pages and flush_cache_dup_mm calls flush_cache_pages.
In some implementations, pdc is more efficient than fdc. Based on
my testing, I don't believe there's any performance benefit on the
c8000.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
2022-05-16 15:14:47 +00:00
|
|
|
void copy_to_user_page(struct vm_area_struct *vma, struct page *page,
|
|
|
|
|
unsigned long user_vaddr, void *dst, void *src, int len);
|
|
|
|
|
void copy_from_user_page(struct vm_area_struct *vma, struct page *page,
|
|
|
|
|
unsigned long user_vaddr, void *dst, void *src, int len);
|
|
|
|
|
void flush_cache_page(struct vm_area_struct *vma, unsigned long vmaddr,
|
|
|
|
|
unsigned long pfn);
|
2006-12-12 05:51:54 -08:00
|
|
|
void flush_cache_range(struct vm_area_struct *vma,
|
|
|
|
|
unsigned long start, unsigned long end);
|
2006-01-13 13:21:06 -07:00
|
|
|
|
2006-12-12 05:51:54 -08:00
|
|
|
#define ARCH_HAS_FLUSH_ANON_PAGE
|
parisc: Rewrite cache flush code for PA8800/PA8900
Originally, I was convinced that we needed to use tmpalias flushes
everwhere, for both user and kernel flushes. However, when I modified
flush_kernel_dcache_page_addr, to use a tmpalias flush, my c8000
would crash quite early when booting.
The PDC returns alias values of 0 for the icache and dcache. This
indicates that either the alias boundary is greater than 16MB or
equivalent aliasing doesn't work. I modified the tmpalias code to
make it easy to try alternate boundaries. I tried boundaries up to
128MB but still kernel tmpalias flushes didn't work on c8000.
This led me to conclude that tmpalias flushes don't work on PA8800
and PA8900 machines, and that we needed to flush directly using the
virtual address of user and kernel pages. This is likely the major
cause of instability on the c8000 and rp34xx machines.
Flushing user pages requires doing a temporary context switch as we
have to flush pages that don't belong to the current context. Further,
we have to deal with pages that aren't present. If a page isn't
present, the flush instructions fault on every line.
Other code has been rearranged and simplified based on testing. For
example, I introduced a flush_cache_dup_mm routine. flush_cache_mm
and flush_cache_dup_mm differ in that flush_cache_mm calls
purge_cache_pages and flush_cache_dup_mm calls flush_cache_pages.
In some implementations, pdc is more efficient than fdc. Based on
my testing, I don't believe there's any performance benefit on the
c8000.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
2022-05-16 15:14:47 +00:00
|
|
|
void flush_anon_page(struct vm_area_struct *vma, struct page *page, unsigned long vmaddr);
|
2006-03-22 08:28:59 -07:00
|
|
|
|
2020-06-04 16:48:10 -07:00
|
|
|
#define ARCH_HAS_FLUSH_ON_KUNMAP
|
parisc: Try to fix random segmentation faults in package builds
PA-RISC systems with PA8800 and PA8900 processors have had problems
with random segmentation faults for many years. Systems with earlier
processors are much more stable.
Systems with PA8800 and PA8900 processors have a large L2 cache which
needs per page flushing for decent performance when a large range is
flushed. The combined cache in these systems is also more sensitive to
non-equivalent aliases than the caches in earlier systems.
The majority of random segmentation faults that I have looked at
appear to be memory corruption in memory allocated using mmap and
malloc.
My first attempt at fixing the random faults didn't work. On
reviewing the cache code, I realized that there were two issues
which the existing code didn't handle correctly. Both relate
to cache move-in. Another issue is that the present bit in PTEs
is racy.
1) PA-RISC caches have a mind of their own and they can speculatively
load data and instructions for a page as long as there is a entry in
the TLB for the page which allows move-in. TLBs are local to each
CPU. Thus, the TLB entry for a page must be purged before flushing
the page. This is particularly important on SMP systems.
In some of the flush routines, the flush routine would be called
and then the TLB entry would be purged. This was because the flush
routine needed the TLB entry to do the flush.
2) My initial approach to trying the fix the random faults was to
try and use flush_cache_page_if_present for all flush operations.
This actually made things worse and led to a couple of hardware
lockups. It finally dawned on me that some lines weren't being
flushed because the pte check code was racy. This resulted in
random inequivalent mappings to physical pages.
The __flush_cache_page tmpalias flush sets up its own TLB entry
and it doesn't need the existing TLB entry. As long as we can find
the pte pointer for the vm page, we can get the pfn and physical
address of the page. We can also purge the TLB entry for the page
before doing the flush. Further, __flush_cache_page uses a special
TLB entry that inhibits cache move-in.
When switching page mappings, we need to ensure that lines are
removed from the cache. It is not sufficient to just flush the
lines to memory as they may come back.
This made it clear that we needed to implement all the required
flush operations using tmpalias routines. This includes flushes
for user and kernel pages.
After modifying the code to use tmpalias flushes, it became clear
that the random segmentation faults were not fully resolved. The
frequency of faults was worse on systems with a 64 MB L2 (PA8900)
and systems with more CPUs (rp4440).
The warning that I added to flush_cache_page_if_present to detect
pages that couldn't be flushed triggered frequently on some systems.
Helge and I looked at the pages that couldn't be flushed and found
that the PTE was either cleared or for a swap page. Ignoring pages
that were swapped out seemed okay but pages with cleared PTEs seemed
problematic.
I looked at routines related to pte_clear and noticed ptep_clear_flush.
The default implementation just flushes the TLB entry. However, it was
obvious that on parisc we need to flush the cache page as well. If
we don't flush the cache page, stale lines will be left in the cache
and cause random corruption. Once a PTE is cleared, there is no way
to find the physical address associated with the PTE and flush the
associated page at a later time.
I implemented an updated change with a parisc specific version of
ptep_clear_flush. It fixed the random data corruption on Helge's rp4440
and rp3440, as well as on my c8000.
At this point, I realized that I could restore the code where we only
flush in flush_cache_page_if_present if the page has been accessed.
However, for this, we also need to flush the cache when the accessed
bit is cleared in ptep_clear_flush_young to keep things synchronized.
The default implementation only flushes the TLB entry.
Other changes in this version are:
1) Implement parisc specific version of ptep_get. It's identical to
default but needed in arch/parisc/include/asm/pgtable.h.
2) Revise parisc implementation of ptep_test_and_clear_young to use
ptep_get (READ_ONCE).
3) Drop parisc implementation of ptep_get_and_clear. We can use default.
4) Revise flush_kernel_vmap_range and invalidate_kernel_vmap_range to
use full data cache flush.
5) Move flush_cache_vmap and flush_cache_vunmap to cache.c. Handle
VM_IOREMAP case in flush_cache_vmap.
At this time, I don't know whether it is better to always flush when
the PTE present bit is set or when both the accessed and present bits
are set. The later saves flushing pages that haven't been accessed,
but we need to flush in ptep_clear_flush_young. It also needs a page
table lookup to find the PTE pointer. The lpa instruction only needs
a page table lookup when the PTE entry isn't in the TLB.
We don't atomically handle setting and clearing the _PAGE_ACCESSED bit.
If we miss an update, we may miss a flush and the cache may get corrupted.
Whether the current code is effectively atomic depends on process control.
When CONFIG_FLUSH_PAGE_ACCESSED is set to zero, the page will eventually
be flushed when the PTE is cleared or in flush_cache_page_if_present. The
_PAGE_ACCESSED bit is not used, so the problem is avoided.
The flush method can be selected using the CONFIG_FLUSH_PAGE_ACCESSED
define in cache.c. The default is 0. I didn't see a large difference
in performance.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Helge Deller <deller@gmx.de>
2024-06-10 18:47:07 +00:00
|
|
|
void kunmap_flush_on_unmap(const void *addr);
|
2006-08-23 09:00:04 -07:00
|
|
|
|
2006-01-13 13:21:06 -07:00
|
|
|
#endif /* _PARISC_CACHEFLUSH_H */
|
|
|
|
|
|